Home › Drivetrain › VF4BM TRANSFER / 4WD / AWD › TRANSFER SYSTEM
RM1440E _52 Drivetrain _056135 VF4BM TRANSFER / 4WD / AWD _0273959 TRANSFER SYSTEM G

VF4BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  INSPECTION  


PROCEDURE

Hide 1.INSPECT INDICATOR LIGHT

a.

4LO Indicator Light:

i.

Turn the ignition switch to ON.


ii.

Move the shift lever to N (vehicle is stopped).


iii.

Change the transfer position switch from H4L to L4L.


iv.

Check the 4LO indicator light.

OK:

4LO indicator light comes on or 4LO indicator light comes on after blinking.


If the result is not as specified, inspect the switch, four wheel drive control ECU and transfer shift actuator assembly. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM). Then check the combination meter (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>PROBLEM SYMPTOMS TABLE).



b.

Center Differential Lock Indicator Light:

i.

Turn the ignition switch to ON.


ii.

Change the transfer position switch from H4F to H4L.


iii.

Check the center differential lock indicator light.

OK:

Center differential lock indicator light comes on or Center differential lock indicator light comes on after blinking


If the result is not as specified, inspect the switches, four wheel drive control ECU, transfer and shift actuator. If the system is normal, there may be a malfunction in the CAN communication system or combination meter. In this case, first check the CAN communication system (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM). Then check the combination meter (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>PROBLEM SYMPTOMS TABLE).



Hide 89533A 2.INSPECT 4 WHEEL DRIVE CONTROL ECU NO.2 (POWER SUPPLY)

a.
U150289E02
2.281,0.927 2.146,0.438 2.146,0.438 2.052,0.438 false 2.146,1 2.031,1.719 false 0.094,0.052 0.281,0.219 0.188,0.167 10 false *a 2.344,0.323 2.688,0.5 0.344,0.177 10 false F46 1.833,1.74 2.24,1.948 0.406,0.208 10 false GND 1.813,0.365 2.063,0.531 0.25,0.167 10 false IG

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
F46-3 (IG) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(Four Wheel Drive Control ECU)

If the result is not as specified, inspect the harness, fuse or connector. If the harness or connector is malfunctioning, repair or replace the harness or connector. If the harness or connector is normal, replace the four wheel drive control ECU (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
F46-4 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.


Hide 89533A 3.INSPECT 4 WHEEL DRIVE CONTROL ECU NO.2 (TRANSFER POSITION SWITCH)

a.
U150290E02
1.24,1.031 1.938,1.635 false 1.083,1.021 0.406,1.635 false 0.094,0.052 0.469,0.323 0.375,0.271 10 false *a 1.146,0.313 1.51,0.49 0.365,0.177 10 false F47 1.833,1.656 2.177,1.833 0.344,0.177 10 false 2-4 0.271,1.656 0.521,1.823 0.25,0.167 10 false LO

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
F47-11 (2-4) - Body ground Ignition switch ON
Transfer position switch H4F
Below 1.5 V
Ignition switch ON
Transfer position switch H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
10.5 to 14 V
F47-13 (LO) - Body ground Ignition switch ON
Transfer position switch H4F
10.5 to 14 V
Ignition switch ON
Transfer position switch H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
Below 1.5 V


Text in Illustration
*a Component with harness connected
(Four Wheel Drive Control ECU)

If the result is not as specified, check the power supply. If the power supply is normal, inspect the transfer position switch (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL SWITCH>ON-VEHICLE INSPECTION).


Hide 36410J 4.INSPECT MULTI MODE TRANSFER SHIFT ACTUATOR

a.

Check the harness and connector between four wheel drive control ECU and transfer shift actuator assembly (multi mode transfer shift actuator).

i.

Disconnect the B47 actuator connector.


ii.

Disconnect the F47 and F46 ECU connectors.


iii.

Measure the resistance according to the value(s) in the table below.

U150298E01
0.506,0.079 0.690,0.292 0.184,0.213 10 *a 5.017,0.079 5.205,0.275 0.188,0.196 10 *b 1.444,0.297 1.780,0.489 0.336,0.193 10 F47 3.517,0.269 3.853,0.461 0.336,0.193 10 F46 5.679,0.184 6.016,0.377 0.336,0.193 10 B47 3.844,1.412 4.142,1.565 0.298,0.152 10 TM1 3.245,1.416 3.557,1.590 0.312,0.174 10 TM2 0.827,1.462 1.180,1.622 0.353,0.161 10 TL2 1.358,1.462 1.641,1.622 0.283,0.161 10 TL3 2.039,1.418 2.228,1.588 0.189,0.169 10 P1 3.769,1.095 3.972,1.408 false 3.534,1.11 3.402,1.39 false 5.198,1.425 5.501,1.588 0.303,0.163 10 TM1 5.594,1.425 5.902,1.576 0.308,0.151 10 CDL 4.76,1.425 5.081,1.585 0.320,0.159 10 TM2 6.521,0.413 6.787,0.552 0.265,0.139 10 TL3 6.549,0.623 6.884,0.784 0.335,0.161 10 GND 6.38,0.189 6.647,0.358 0.266,0.169 10 TL2 1.2,0.924 0.999,1.44 false 1.34,0.94 1.47,1.44 false 1.973,0.924 2.101,1.383 false 5.246,0.899 4.909,1.397 false 5.445,0.928 5.343,1.397 false 5.662,1.103 5.711,1.425 false 6.051,0.803 6.492,0.494 false 5.858,0.795 6.334,0.273 false 6.25,0.858 6.509,0.697 false

Standard resistance:
Tester Connection Condition Specified Condition
F47-7 (TL2) - B47-4 (TL2) Always Below 1 Ω
F47-7 (TL2) - Body ground Always 100 kΩ or higher
F47-8 (TL3) - B47-5 (TL3) Always Below 1 Ω
F47-8 (TL3) - Body ground Always 100 kΩ or higher
F47-14 (P1) - B47-9 (CDL) Always Below 1 Ω
F47-14 (P1) - Body ground Always 100 kΩ or higher
F46-7 (TM2) - B47-1 (TM2) Always Below 1 Ω
F46-7 (TM2) - Body ground Always 100 kΩ or higher
F46-8 (TM1) - B47-2 (TM1) Always Below 1 Ω
F46-8 (TM1) - Body ground Always 100 kΩ or higher
B47-6 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Four Wheel Drive Control ECU)
*b Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

If the result is not as specified, repair or replace the harness or connector. If the harness or connector is normal, check the ECU output voltage.



b.

Check the four wheel drive control ECU (multi mode transfer shift actuator circuit).

i.

Connect the F47 and F46 ECU connectors.


ii.

Connect the B47 actuator connector.


iii.
U150291E01
0.097,0.062 0.281,0.225 0.184,0.163 10 *a 1.14,0.281 1.449,0.437 0.309,0.156 10 F47 2.309,0.281 2.618,0.437 0.309,0.156 10 F46 1.512,1.67 1.784,1.821 0.272,0.151 10 TL2 2.017,1.67 2.361,1.821 0.344,0.151 10 GND 2.635,1.67 2.956,1.821 0.321,0.151 10 TM1 3.082,1.67 3.399,1.821 0.316,0.151 10 TM2 0.198,1.67 0.409,1.834 0.211,0.165 10 P1 0.619,1.67 0.886,1.834 0.267,0.165 10 TL3 1.437,1.041 0.809,1.652 false 1.007,1.036 0.344,1.649 false 1.518,1.044 1.656,1.655 false 2.443,1.146 2.782,1.604 false 2.179,0.989 2.197,1.602 false 2.605,1.125 3.246,1.636 false

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
F46-8 (TM1) - F46-4 (GND) Ignition switch ON
Transfer position switch H4F → H4L (During operation of multi mode transfer shift actuator motor from FREE to LOCK)
10 to 14 V
Ignition switch ON
Transfer position switch H4F → H4L (Multi mode transfer shift actuator motor stopped)
Below 1.5 V
F46-7 (TM2) - F46-4 (GND) Ignition switch ON
Transfer position switch H4L → H4F (During operation of multi mode transfer shift actuator motor from LOCK to FREE)
10 to 14 V
Ignition switch ON
Transfer position switch H4L → H4F (Multi mode transfer shift actuator motor stopped)
Below 1.5 V
F47-7 (TL2) - F46-4 (GND) Ignition switch ON
Transfer position switch H4L or L4L
Below 1.5 V
Ignition switch ON
Transfer position switch H4F
10.5 to 14 V
F47-8 (TL3) - F46-4 (GND) Ignition switch ON
Transfer position switch H4L or L4L
10.5 to 14 V
Ignition switch ON
Transfer position switch H4F
Below 1.5 V
F47-14 (P1) - F46-4 (GND) Ignition switch ON
Transfer position switch H4F
9.5 to 14 V
Ignition switch ON
Transfer position switch H4L or L4L
Below 1.5 V


Text in Illustration
*a Component with harness connected
(Four Wheel Drive Control ECU)

If the result is not as specified, determine if a malfunction is on the ECU side or actuator side by disconnecting the connector of the transfer shift actuator, and then check the ECU output voltage.



c.

Check the four wheel drive control ECU output voltage.

i.

Disconnect the B47 actuator connector.


ii.

Connect the F47 and F46 ECU connectors.


iii.
U150301E02
1.031,0.958 0.531,1.438 true 1.26,1 1.031,1.604 true 1.542,1.229 1.656,1.604 true 1.781,1 2.125,1.615 true 2.01,0.885 2.396,0.375 true 2.25,0.927 2.604,0.719 true 0.094,0 0.302,0.167 0.208,0.167 10 false *a 0.354,0.479 0.635,0.625 0.281,0.146 10 false B47 0.865,1.615 1.229,1.813 0.365,0.198 10 false TM1 0.365,1.458 0.719,1.625 0.354,0.167 10 false TM2 2.042,1.635 2.344,1.823 0.302,0.188 10 false TL2 2.354,0.229 2.677,0.417 0.323,0.188 10 false TL3 2.635,0.615 3.125,0.76 0.49,0.146 10 false GND1 1.531,1.615 1.865,1.781 0.333,0.167 10 false CDL

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
B47-9 (CDL) - B47-6 (GND1) Ignition switch ON 9.5 to 14 V
B47-4 (TL2) - B47-6 (GND1) Ignition switch ON 10.5 to 14 V
B47-5 (TL3) - B47-6 (GND1) Ignition switch ON 10.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

If the result is not as specified, replace the four wheel drive control ECU (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL). If the voltage is normal, inspect the multi mode transfer shift actuator, because the voltage applied to the motor cannot be measured.



d.

Inspect the multi mode transfer shift actuator (transfer shift actuator assembly).

i.

Remove the transfer shift actuator assembly (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY).


ii.

Check the LOCK to FREE switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the LOCK to FREE position.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the stop LP relay.


C218269E07
5.833,1.448 6.031,0.927 false 5.563,1.448 5.344,0.917 false 6.042,2.021 6.594,2.021 false 6.042,2.438 6.594,2.656 false 6.073,1.448 6.51,0.917 false 2.104,2.823 1.76,2.823 false 2.063,3.375 1.563,2.875 false 0.979,3.375 1.24,2.875 false 0.594,3.385 1.083,2.885 false 0.875,2.823 0.563,2.823 false 1.458,3.01 1.677,3.354 false 1.271,3.042 1.323,3.365 false 4.771,0.292 4.979,0.438 0.208,0.146 10 false *1 2.552,1.042 2.76,1.188 0.208,0.146 10 false *1 5.271,0.792 5.458,0.969 0.188,0.177 10 false 1 6.573,0.823 6.74,1.021 0.167,0.198 10 false 2 6.01,0.771 6.26,0.938 0.25,0.167 10 false 4 6.646,1.948 6.813,2.135 0.167,0.188 10 false 5 6.656,2.604 6.823,2.76 0.167,0.156 10 false 3 0.521,2.344 0.708,2.5 0.188,0.156 10 false *a 1.99,3.396 2.365,3.552 0.375,0.156 10 false TM1 2.156,2.75 2.5,2.917 0.344,0.167 10 false TM2 0.427,3.406 0.74,3.573 0.313,0.167 10 false TL3 0.177,2.76 0.594,2.927 0.417,0.167 10 false GND1 1.167,3.375 1.531,3.542 0.365,0.167 10 false GND 0.708,1.073 1.021,1.26 0.313,0.188 10 false *b 0.792,3.406 1.125,3.583 0.333,0.177 10 false TL2 1.573,3.375 1.906,3.552 0.333,0.177 10 false CDL

1.

After the LOCK to FREE switch is complete, inspect the center differential lock detection switch and limit switch.

Standard resistance:
Tester Connection Condition Specified Condition
4 (TL2) - 6 (GND1) After LOCK to FREE switch is complete 0.5 MΩ or higher
5 (TL3) - 6 (GND1) After LOCK to FREE switch is complete Below 12.5 Ω
9 (CDL) - 10 (GND) After LOCK to FREE switch is complete 0.5 MΩ or higher


Text in Illustration
*1 Stop LP Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b LOCK to FREE



iii.

Check the FREE to LOCK switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the FREE to LOCK position.

C218270E06
6.042,2.021 6.594,2.021 false 6.042,2.438 6.594,2.656 false 6.083,1.458 6.521,0.927 false 5.823,1.448 6.021,0.927 false 5.563,1.458 5.354,0.927 false 2.115,2.844 1.771,2.844 true 2.073,3.406 1.563,2.906 true 0.969,3.333 1.26,2.875 true 0.719,3.323 1.073,2.906 true 0.906,2.833 0.563,2.833 true 1.448,3.031 1.635,3.385 true 1.271,3.063 1.313,3.365 true 5.052,0.354 5.24,0.552 0.188,0.198 10 false *1 2.594,1.031 2.781,1.229 0.188,0.198 10 false *1 5.26,0.823 5.448,1 0.188,0.177 10 false 1 6.563,0.823 6.729,1.021 0.167,0.198 10 false 2 6.042,0.823 6.292,0.99 0.25,0.167 10 false 4 6.646,1.927 6.813,2.115 0.167,0.188 10 false 5 6.635,2.563 6.802,2.719 0.167,0.156 10 false 3 0.458,2.146 0.635,2.344 0.177,0.198 10 false *a 1.979,3.406 2.354,3.563 0.375,0.156 10 false TM1 2.146,2.771 2.49,2.938 0.344,0.167 10 false TM2 0.469,3.313 0.781,3.479 0.313,0.167 10 false TL3 0.156,2.75 0.604,2.917 0.448,0.167 10 false GND1 1.167,3.375 1.51,3.542 0.344,0.167 10 false GND 0.854,0.979 1.146,1.167 0.292,0.188 10 false *b 0.802,3.354 1.135,3.531 0.333,0.177 10 false TL2 1.573,3.427 1.906,3.604 0.333,0.177 10 false CDL

1.

After the FREE to LOCK switch is complete, inspect the center differential lock detection switch and limit switch.

Standard resistance:
Tester Connection Condition Specified Condition
4 (TL2) - 6 (GND1) After FREE to LOCK switch is complete Below 12.5 Ω
5 (TL3) - 6 (GND1) After FREE to LOCK switch is complete 0.5 MΩ or higher
9 (CDL) - 10 (GND) After FREE to LOCK switch is complete Below 12.5 Ω


Text in Illustration
*1 Stop LP Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b FREE to LOCK

If the result is not as specified, replace the transfer shift actuator assembly (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY). If the transfer shift actuator assembly is normal, replace the four wheel drive control ECU (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL).




Hide 36410J 5.INSPECT HIGH-LOW TRANSFER SHIFT ACTUATOR

a.

Check the harness and connector between four wheel drive control ECU and transfer shift actuator (high-low transfer shift actuator).

i.

Disconnect the B47 actuator connector.


ii.

Disconnect the F47 and F46 ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

U150299E01
0.506,0.079 0.690,0.292 0.184,0.213 10 *a 5.017,0.079 5.205,0.275 0.188,0.196 10 *b 1.443,0.296 1.780,0.489 0.336,0.193 10 F47 3.517,0.268 3.853,0.461 0.336,0.193 10 F46 5.679,0.184 6.016,0.377 0.336,0.193 10 B47 3.245,1.416 3.557,1.590 0.312,0.174 10 HM2 3.914,1.416 4.226,1.590 0.312,0.174 10 HM1 0.203,1.462 0.556,1.622 0.353,0.161 10 HL1 0.751,1.462 1.034,1.622 0.283,0.161 10 HL2 3.448,0.897 4.057,1.39 false 5.198,1.425 5.529,1.588 0.331,0.163 10 HM1 4.76,1.425 5.081,1.585 0.320,0.159 10 HM2 6.6,0.826 6.886,0.965 0.286,0.139 10 HL1 5.744,1.422 6.079,1.582 0.335,0.161 10 GND 6.564,1.319 6.872,1.488 0.308,0.169 10 HL2 0.577,0.924 0.375,1.439 false 0.728,0.93 0.863,1.439 false 5.256,1.083 4.909,1.397 false 5.48,1.096 5.343,1.397 false 5.844,1.103 5.893,1.425 false 6.25,0.979 6.57,0.907 false 6.019,1.098 6.518,1.382 false 3.402,1.116 3.402,1.387 false

Standard resistance:
Tester Connection Condition Specified Condition
F47-1 (HL1) - B47-12 (HL1) Always Below 1 Ω
F47-1 (HL1) - Body ground Always 100 kΩ or higher
F47-2 (HL2) - B47-11 (HL2) Always Below 1 Ω
F47-2 (HL2) - Body ground Always 100 kΩ or higher
F46-2 (HM1) - B47-8 (HM1) Always Below 1 Ω
F46-2 (HM1) - Body ground Always 100 kΩ or higher
F46-6 (HM2) - B47-7 (HM2) Always Below 1 Ω
F46-6 (HM2) - Body ground Always 100 kΩ or higher
B47-10 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Four Wheel Drive Control ECU)
*b Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

If the result is not as specified, repair or replace the harness or connector. If the harness or connector is normal, check the ECU output voltage.



b.

Check the four wheel drive control ECU (high-low transfer shift actuator circuit).

i.

Connect the F47 and F46 ECU connectors.


ii.

Connect the B47 actuator connector.


iii.
U150292E01
0.097,0.079 0.281,0.242 0.184,0.163 10 *a 1.14,0.298 1.449,0.453 0.309,0.156 10 F47 2.309,0.298 2.618,0.453 0.309,0.156 10 F46 1.792,1.906 2.091,2.057 0.299,0.151 10 HL1 2.017,1.687 2.361,1.837 0.344,0.151 10 GND 2.824,1.687 3.146,1.837 0.321,0.151 10 HM2 3.082,0.42 3.399,0.571 0.316,0.151 10 HM1 1.504,1.69 1.789,1.854 0.286,0.165 10 HL2 1.875,1.046 1.694,1.672 false 1.966,1.06 1.935,1.891 false 2.717,1.163 2.971,1.621 false 2.197,1.006 2.197,1.618 false 2.735,0.924 3.042,0.517 false

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
F46-6 (HM2) - F46-4 (GND) Ignition switch ON
Transfer position switch L4L → H4L (During operation of high-low transfer shift actuator motor from LOW to HIGH)
10 to 14 V
Ignition switch ON
Transfer position switch L4L → H4L (High-low transfer shift actuator motor stopped)
Below 1.5 V
F46-2 (HM1) - F46-4 (GND) Ignition switch ON
Transfer position switch H4L → L4L (During operation of high-low transfer shift actuator motor from HIGH to LOW)
10 to 14 V
Ignition switch ON
Transfer position switch H4L → L4L (High-low transfer shift actuator motor stopped)
Below 1.5 V
F47-1 (HL1) - F46-4 (GND) Ignition switch ON
Transfer position switch H4F or H4L
10.5 to 14 V
Ignition switch ON
Transfer position switch L4L
Below 1.5 V
F47-2 (HL2) - F46-4 (GND) Ignition switch ON
Transfer position switch H4F or H4L
Below 1.5 V
Ignition switch ON
Transfer position switch L4L
10.5 to 14 V


Text in Illustration
*a Component with harness connected
(Four Wheel Drive Control ECU)

If the result is not as specified, determine if the malfunction is on the ECU side or actuator side by disconnecting the connector of the high-low transfer shift actuator, and then checking the ECU output voltage.



c.

Check the four wheel drive control ECU output voltage.

i.

Connect the F47 and F46 ECU connectors.


ii.

Disconnect the B47 actuator connector.


iii.
U150300E02
1.031,1.167 0.542,1.396 false 1.302,1.229 1.177,1.75 false 1.75,1.24 1.896,1.76 false 1.979,1.24 2.583,1.708 false 2.25,1.188 2.667,1.292 false 0.094,0 0.302,0.167 0.208,0.167 10 false *a 0.344,0.49 0.625,0.635 0.281,0.146 10 false B47 1,1.76 1.365,1.958 0.365,0.198 10 false HM1 0.24,1.344 0.594,1.51 0.354,0.167 10 false HM2 2.448,1.729 2.75,1.917 0.302,0.188 10 false HL2 2.677,1.24 3,1.427 0.323,0.188 10 false HL1 1.74,1.75 2.073,1.917 0.333,0.167 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
B47-11 (HL2) - B47-10 (GND) Ignition switch ON 10.5 to 14 V
B47-12 (HL1) - B47-10 (GND) Ignition switch ON 10.5 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)

If the result is not as specified, replace the four wheel drive control ECU (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL). If the voltage is normal, inspect the high-low transfer shift actuator, because the voltage applied to the motor cannot be measured.



d.

Inspect the high-low transfer shift actuator transfer shift actuator assembly.

i.

Remove the transfer shift actuator assembly (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY).


ii.

Check the HIGH to LOW switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the HIGH to LOW position.

NOTICE:
·

Perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the stop LP relay.


C218271E05
5.958,2.385 6.51,2.385 false 5.958,2.781 6.51,3 false 6.01,1.802 6.448,1.281 false 5.74,1.802 5.938,1.292 false 5.479,1.813 5.26,1.292 false 0.833,2.271 0.49,2.271 true 1.063,2.219 0.542,1.771 true 1.198,2.219 0.927,1.542 true 1.521,2.219 1.625,1.594 true 1.719,2.25 1.948,1.833 true 4.677,0.563 4.854,0.729 0.177,0.167 10 false *1 2.677,1.49 2.854,1.656 0.177,0.167 10 false *1 5.167,1.198 5.354,1.375 0.188,0.177 10 false 1 6.5,1.198 6.667,1.396 0.167,0.198 10 false 2 6,1.198 6.25,1.365 0.25,0.167 10 false 4 6.583,2.281 6.75,2.469 0.167,0.188 10 false 5 6.583,2.927 6.75,3.083 0.167,0.156 10 false 3 0.344,1.229 0.542,1.396 0.198,0.167 10 false *a 1.698,1.49 2.073,1.646 0.375,0.156 10 false HM1 2,1.729 2.344,1.896 0.344,0.167 10 false HM2 0.188,2.198 0.5,2.365 0.313,0.167 10 false HL1 0.604,1.458 0.979,1.625 0.375,0.167 10 false GND 0.646,0.948 0.844,1.104 0.198,0.156 10 false *b 0.24,1.698 0.573,1.875 0.333,0.177 10 false HL2

1.

After the HIGH to LOW switch is complete, inspect the limit switch.

Standard resistance:
Tester Connection Condition Specified Condition
12 (HL1) - 10 (GND) After HIGH to LOW switch is complete Below 12.5 Ω
11 (HL2) - 10 (GND) After HIGH to LOW switch is complete 0.5 MΩ or higher


Text in Illustration
*1 Stop LP Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b HIGH to LOW



iii.

Check the LOW to HIGH switch.

Connect lines via a relay as shown in the illustration, then check that the actuator fork moves from the LOW to HIGH position.

C218272E05
5.948,2.375 6.5,2.375 false 5.958,2.792 6.51,3.01 false 6,1.802 6.438,1.271 false 5.74,1.813 5.927,1.292 false 5.479,1.802 5.26,1.271 false 0.865,2.26 0.521,2.26 true 1.073,2.219 0.563,1.781 true 1.24,2.219 0.969,1.531 true 1.573,2.208 1.677,1.573 true 1.729,2.219 1.948,1.792 true 4.906,0.552 5.073,0.75 0.167,0.198 10 false *1 2.615,1.521 2.781,1.719 0.167,0.198 10 false *1 5.156,1.198 5.344,1.375 0.188,0.177 10 false 1 6.458,1.177 6.625,1.375 0.167,0.198 10 false 2 5.917,1.146 6.167,1.313 0.25,0.167 10 false 4 6.542,2.292 6.708,2.479 0.167,0.188 10 false 5 6.542,2.948 6.708,3.104 0.167,0.156 10 false 3 0.323,1.167 0.531,1.323 0.208,0.156 10 false *a 2.01,1.698 2.385,1.854 0.375,0.156 10 false HM2 1.719,1.458 2.063,1.625 0.344,0.167 10 false HM1 0.25,2.198 0.563,2.365 0.313,0.167 10 false HL1 0.635,1.458 1.01,1.625 0.375,0.167 10 false GND 0.948,0.917 1.167,1.083 0.219,0.167 10 false *b 0.281,1.688 0.615,1.865 0.333,0.177 10 false HL2

1.

After the LOW to HIGH switch is complete, inspect the limit switch.

Standard resistance:
Tester Connection Condition Specified Condition
12 (HL1) - 10 (GND) After LOW to HIGH switch is complete 0.5 MΩ or higher
11 (HL2) - 10 (GND) After LOW to HIGH switch is complete Below 12.5 Ω


Text in Illustration
*1 Stop LP Relay - -
*a Component without harness connected
(Transfer Shift Actuator Assembly)
*b LOW to HIGH

If the result is not as specified, replace the transfer shift actuator assembly (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>TRANSFER ASSEMBLY>DISASSEMBLY). If the transfer shift actuator assembly is normal, replace the four wheel drive control ECU (See page Drivetrain>VF4BM TRANSFER / 4WD / AWD>4WD CONTROL ECU>REMOVAL).