Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › FRONT WHEEL ALIGNMENT
RM1440E _53 Suspension _056138 ALIGNMENT / HANDLING DIAGNOSIS _0273981 FRONT WHEEL ALIGNMENT N

ALIGNMENT / HANDLING DIAGNOSIS  FRONT WHEEL ALIGNMENT  ADJUSTMENT  


CAUTION / NOTICE / HINT

NOTICE:

If the wheel alignment has been adjusted, and if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

·

Perform zero point calibration of the yaw rate and acceleration sensor and the test mode inspection.



PROCEDURE

Hide 1.INSPECT TIRES

Hide 2.MEASURE VEHICLE HEIGHT

NOTICE:

Before inspecting the wheel alignment, adjust the vehicle height to the specification.


a.
C361824E01
0.146,0.323 0.49,0.552 0.344,0.229 10 false *a 0.167,2.354 0.51,2.583 0.344,0.229 10 false *b 0.49,1.542 0.833,1.771 0.344,0.229 10 false A 1.167,1.635 1.385,1.854 0.219,0.219 10 false B 0.188,3.667 0.406,3.885 0.219,0.219 10 false D 3.125,3.594 3.292,3.781 0.167,0.188 10 false C

Press down on the vehicle several times to stabilize the suspension, and then measure the vehicle height.

Text in Illustration
*a Front Side
*b Rear Side

Standard Vehicle Height (Unloaded Vehicle):
Vehicle Model Grade Front (A - B) Rear (C - D)
GRN280L-GKAGK SR5 96.5 mm (3.80 in.) 67.9 mm (2.67 in.)
Limited 97.3 mm (3.83 in.) 68.7 mm (2.70 in.)
GRN285L-GKAGK SR5 93.9 mm (3.70 in.) 68.1 mm (2.68 in.)
Limited 94.6 mm (3.72 in.) 68.8 mm (2.71 in.)


Measuring points:
A:

Ground clearance of the center of the front wheel

B:

Ground clearance of the center of the front adjusting cam bolt

C:

Ground clearance of the center of the rear wheel

D:

Ground clearance of the center of the rear lower control arm front side


If the vehicle height is not as specified, adjust the height by pressing down on the vehicle several times to stabilize the suspension.


Hide 3.INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

a.
C132440E16
2.77,0.758 2.956,0.923 0.187,0.165 10 *2 2.403,1.106 2.51,0.827 2.51,0.827 2.738,0.827 false 0.603,0.704 1.036,0.704 1.036,0.704 1.036,1.478 false 0.363,0.621 0.554,0.775 0.191,0.154 10 *1

Install a camber-caster-kingpin gauge or place the front wheels on the center of a wheel alignment tester.

Text in Illustration
*1 Wheel Alignment Tester
*2 Gauge


b.

Inspect the camber, caster and steering axis inclination.

Standard Camber Inclination (Unloaded Vehicle):
Vehicle Model Grade Camber Inclination Right-left Difference
GRN280L-GKAGK SR5 -0°4' +/-45' (-0.07° +/-0.75°) 45' (0.75°) or less
Limited -0°5' +/-45' (-0.08° +/-0.75°) 45' (0.75°) or less
GRN285L-GKAGK SR5 0°1' +/-45' (0.02° +/-0.75°) 45' (0.75°) or less
Limited -0°1' +/-45' (-0.02° +/-0.75°) 45' (0.75°) or less


Standard Caster Inclination (Unloaded Vehicle):
Vehicle Model Grade Caster Inclination Right-left Difference
GRN280L-GKAGK SR5 3°15' +/-45' (3.25° +/-0.75°) 45' (0.75°) or less
Limited 3°16' +/-45' (3.27° +/-0.75°) 45' (0.75°) or less
GRN285L-GKAGK SR5 3°12' +/-45' (3.20° +/-0.75°) 45' (0.75°) or less
Limited 3°14' +/-45' (3.23° +/-0.75°) 45' (0.75°) or less


Standard Steering Axis Inclination (Unloaded Vehicle):
Vehicle Model Grade Steering Axis Inclination
GRN280L-GKAGK SR5 12°13' +/-45' (12.22° +/-0.75°)
Limited 12°14' +/-45' (12.23° +/-0.75°)
GRN285L-GKAGK SR5 12°9' +/-45' (12.15° +/-0.75°)
Limited 12°10' +/-45' (12.17° +/-0.75°)



Hide 4.ADJUST CAMBER AND CASTER

HINT:

After the camber has been adjusted, inspect the toe-in.


a.

Loosen the front adjusting cam bolt and rear adjusting cam nut.


b.

Turn the front adjusting cam and rear adjusting cam in both directions, and adjust the camber and caster to the center value.

HINT:
·

The camber and caster should be as close as possible to the center value.

·

Adjust the camber and caster within +/- 30'.



C361826E01
2.75,0.833 3.063,1.031 0.313,0.198 10 false *1 4.188,0.833 4.5,1.031 0.313,0.198 10 false *2 2.792,2.302 3.104,2.5 0.313,0.198 10 false *3 4.208,2.302 4.521,2.5 0.313,0.198 10 false *4

Text in Illustration
*1 Front Adjusting Cam LH *2 Front Adjusting Cam RH
*3 Rear Adjusting Cam LH *4 Rear Adjusting Cam RH
V100135

Front - -


c.
C361827E01
2.635,1.99 2.635,1.833 2.635,1.833 2.802,1.833 false 2.635,2.292 2.958,2.292 2.958,2.292 2.958,2.531 false 2.604,3.021 2.927,3.021 2.927,3.021 2.927,3.24 false 2.646,3.875 2.896,3.875 2.896,3.875 2.896,4.031 false 1.01,0.76 1.323,0.958 0.313,0.198 10 false *1 1.031,1.021 1.354,1.219 0.323,0.198 10 false *2 0.698,1.25 1.01,1.448 0.313,0.198 10 false *a 0.698,1.49 1.01,1.688 0.313,0.198 10 false *b 0.375,3.052 0.688,3.25 0.313,0.198 10 false *3 0.229,2.49 0.542,2.688 0.313,0.198 10 false (+) 0.25,3.667 0.563,3.865 0.313,0.198 10 false (-) 1.563,4.177 1.875,4.375 0.313,0.198 10 false *4 2.74,4.042 3.052,4.24 0.313,0.198 10 false 0°00' 2.729,4.208 3.146,4.406 0.417,0.198 10 false (+/-0°) 2.771,3.25 3.177,3.458 0.406,0.208 10 false -0°20' 2.74,3.427 3.281,3.635 0.542,0.208 10 false (-0.33°) 2.813,2.573 3.219,2.781 0.406,0.208 10 false 3°30' 2.781,2.75 3.188,2.958 0.406,0.208 10 false (3.50°) 2.854,1.75 3.26,1.958 0.406,0.208 10 false 3°20' 2.813,1.938 3.219,2.146 0.406,0.208 10 false (3.33°) 2.156,4.271 2.469,4.469 0.313,0.198 10 false (+) 1.021,4.302 1.333,4.5 0.313,0.198 10 false (-)

Read the adjustment chart (example).

Text in Illustration
*1 Caster
*2 Camber
*3 Front Adjusting Cam
*4 Rear Adjusting Cam
*a Measured Value
*b Standard Value

i.

Find the wheel alignment standard value applicable for the particular model.


ii.

Mark the selected standard value on the adjustment chart.

Standard Value (Reference)
Camber Caster
0°00' (0.00°) 3°30' (3.50°)


iii.

Mark the alignment value measured when the vehicle is unloaded on the adjustment chart.

Measured Value (Reference)
Camber Caster
-0°20' (-0.33°) 3°20' (3.33°)


iv.

As shown in the chart, read the distance from the marked point to 0, and adjust the front and/ or rear adjusting cams accordingly.

Amount to Turn Adjusting Cams (by Gradation)
Front Adjusting Cam Rear Adjusting Cam
+3 +2

C213231E12
3.083,4.406 3.198,4.594 0.115,0.188 10 true 0 3.229,4.521 3.344,4.708 0.115,0.188 10 true 0 3.073,4.188 3.188,4.375 0.115,0.188 10 true 1 3.073,3.969 3.188,4.156 0.115,0.188 10 true 2 3.073,3.729 3.188,3.917 0.115,0.188 10 true 3 3.063,3.5 3.177,3.688 0.115,0.188 10 true 4 3.052,3.271 3.167,3.458 0.115,0.188 10 true 5 3.052,3.042 3.167,3.229 0.115,0.188 10 true 6 3.042,2.823 3.156,3.01 0.115,0.188 10 true 7 3.052,2.573 3.167,2.76 0.115,0.188 10 true 8 3.042,2.344 3.156,2.531 0.115,0.188 10 true 9 3.385,4.521 3.5,4.708 0.115,0.188 10 true 1 3.615,4.51 3.729,4.698 0.115,0.188 10 true 2 3.833,4.5 3.948,4.688 0.115,0.188 10 true 3 4.073,4.51 4.188,4.698 0.115,0.188 10 true 4 4.323,4.521 4.438,4.708 0.115,0.188 10 true 5 4.542,4.521 4.656,4.708 0.115,0.188 10 true 6 4.781,4.51 4.896,4.698 0.115,0.188 10 true 7 5.01,4.51 5.125,4.698 0.115,0.188 10 true 8 5.219,4.51 5.354,4.708 0.135,0.198 10 true 9 2.896,4.521 3.052,4.708 0.156,0.188 10 true -1 2.646,4.51 2.802,4.698 0.156,0.188 10 true -2 2.417,4.521 2.573,4.708 0.156,0.188 10 true -3 2.188,4.521 2.344,4.708 0.156,0.188 10 true -4 1.969,4.521 2.125,4.708 0.156,0.188 10 true -5 1.74,4.51 1.896,4.698 0.156,0.188 10 true -6 1.51,4.51 1.667,4.698 0.156,0.188 10 true -7 1.281,4.521 1.438,4.708 0.156,0.188 10 true -8 1.031,4.51 1.188,4.698 0.156,0.188 10 true -9 3.031,4.885 3.188,5.073 0.156,0.188 10 true -2 3.031,5.115 3.188,5.302 0.156,0.188 10 true -3 3.031,5.344 3.188,5.531 0.156,0.188 10 true -4 3.031,5.573 3.188,5.76 0.156,0.188 10 true -5 3.031,5.792 3.188,5.979 0.156,0.188 10 true -6 3.042,6.031 3.198,6.219 0.156,0.188 10 true -7 3.031,6.26 3.188,6.448 0.156,0.188 10 true -8 5.698,5.656 6.323,5.844 0.625,0.188 10 false 0°00' 5.698,6.75 6.323,6.938 0.625,0.188 10 false 0°30' 5.698,4.427 6.323,4.615 0.625,0.188 10 false -0°30' 5.604,3.271 6.229,3.458 0.625,0.188 10 false -1°00' 5.563,2.833 5.99,3.021 0.427,0.188 10 false 3°40' 5.552,2.531 5.979,2.719 0.427,0.188 10 false 3°30' 5.365,2.021 5.792,2.208 0.427,0.188 10 false 3°20' 4.958,1.729 5.385,1.917 0.427,0.188 10 false 3°00' 4,2.01 4.427,2.198 0.427,0.188 10 false 2°40' 3.583,1.75 4.01,1.938 0.427,0.188 10 false 2°20' 2.667,2 3.094,2.188 0.427,0.188 10 false 2°00' 2.271,1.729 2.698,1.917 0.427,0.188 10 false 1°40' 0.427,4.958 0.854,5.146 0.427,0.188 10 false 0°40' 0.438,5.729 0.865,5.917 0.427,0.188 10 false 1°00' 1.448,6.948 1.875,7.135 0.427,0.188 10 false 4°00' 1.823,7.208 2.25,7.396 0.427,0.188 10 false 4°20' 2.74,6.948 3.167,7.135 0.427,0.188 10 false 4°40' 3.156,7.208 3.583,7.396 0.427,0.188 10 false 5°00' 4.063,6.958 4.49,7.146 0.427,0.188 10 false 5°20' 6.646,4.708 6.906,4.917 0.26,0.208 10 false (+) 0.458,4.688 0.719,4.896 0.26,0.208 10 false (-) 3.135,8.021 3.448,8.302 0.313,0.281 10 false (-) 3.115,1 3.375,1.208 0.26,0.208 10 false (+) 1.052,0.656 1.333,0.885 0.281,0.229 10 false *1 1.063,0.917 1.344,1.146 0.281,0.229 10 false *2 3.115,0.781 3.396,1.01 0.281,0.229 10 false *3 0.51,4.146 0.792,4.375 0.281,0.229 10 false *4 3.031,4.635 3.198,4.833 0.167,0.198 10 true -1 3.031,6.479 3.177,6.656 0.146,0.177 10 true -9

Text in Illustration
*1 Camber *2 Caster
*3 Front Cam Graduation *4 Rear Cam Graduation



Hide 5.INSPECT TOE-IN

a.
U116701E05
0.302,0.073 0.531,0.313 0.229,0.24 10 false A 1.688,0.115 1.823,0.26 0.135,0.146 10 false D 3.083,0.052 3.219,0.198 0.135,0.146 10 false B 1.729,1.906 1.885,2.094 0.156,0.188 10 false C

Bounce the vehicle up and down at the corners to stabilize the suspension and inspect the toe-in.

Text in Illustration
V100135

Front

Standard Toe-in (Unloaded Vehicle):
Vehicle Model Grade Toe-in
GRN280L-GKAGK SR5 A + B: 0°8' +/-0°9' (0.14° +/-0.15°)
C - D: 1.86 +/-2 mm (0.073 +/-0.08 in.)
Limited A + B: 0°8' +/-0°9' (0.14° +/-0.15°)
C - D: 1.68 +/-2 mm (0.066 +/-0.08 in.)
GRN285L-GKAGK SR5 A + B: 0°12' +/-0°9' (0.20° +/-0.15°)
C - D: 2.46 +/-2 mm (0.097 +/-0.08 in.)
Limited A + B: 0°12' +/-0°9' (0.20° +/-0.15°)
C - D: 2.30 +/-2 mm (0.091 +/-0.08 in.)


If the toe-in is not within the specified range, adjust it at the rack ends.


Hide 6.ADJUST TOE-IN

a.

Detach the rack boot set clips.


b.

Loosen the tie rod end lock nuts.


c.

Turn the right and left rack ends by an equal amount to adjust the toe-in to the center value.


d.
G020168E07
1.531,1.083 1.771,1.333 0.24,0.25 10 true *a

Check that the lengths of the right and left rack ends are approximately the same.

Text in Illustration
*a Length
V100135

Lock Nut

Standard difference:

0 +/-1 mm (0 +/-0.0394 in.) or less



e.

Tighten the tie rod end lock nuts.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)


f.

Place the boots on the seats and install the clips.

HINT:

Make sure that the boots are not twisted.



Hide 7.INSPECT WHEEL ANGLE

a.
F046953E27
1.531,0.417 1.688,0.677 0.156,0.26 10 false A 2.646,0.417 2.781,0.615 0.135,0.198 10 false A 1.75,0.417 1.917,0.667 0.167,0.25 10 false B 2.417,0.417 2.552,0.656 0.135,0.24 10 false B 2,1.281 2.448,1.5 0.448,0.219 10 false A: *a 2.01,1.583 2.49,1.792 0.479,0.208 10 false B: *b

Turn the steering wheel to the left and right full lock positions, and measure the turning angle.

Text in Illustration
*a Inside
*b Outside
V100135

Front

Standard Wheel Turning Angle (Unloaded Vehicle):
Vehicle Model Grade Inside Wheel Angle Outside Wheel Angle: Reference
GRN280L-GKAGK SR5 33°54' to 36°54'
(33.90° to 36.90°)
32°24'
(32.40°)
Limited 33°54' to 36°54'
(33.90° to 36.90°)
32°23'
(32.38°)
GRN285L-GKAGK SR5 33°57' to 36°57'
(33.95° to 36.95°)
32°28'
(32.47°)
Limited 33°56' to 36°56'
(33.93° to 36.93°)
32°27'
(32.45°)


If the right and left inside wheel angles differ from the specified range, check the right and left rack end lengths.


Hide 8.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 9.PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION

HINT:

Perform the yaw rate sensor zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


Hide 10.PERFORM INITIALIZATION

HINT:

Some systems need to be initialized after the wheel alignment is adjusted (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).