Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C0226  SFR Solenoid Circuit  C0236  SFL Solenoid Circuit  C0246  SRR Solenoid Circuit  C0256  SRL Solenoid Circuit  C1225  SM Solenoid Circuit  C1226  SA2 Solenoid Circuit  C1227  SA3 Solenoid Circuit  C1228  STR Solenoid Circuit  


DESCRIPTION

The solenoid turns on when signals are received from the skid control ECU and controls the pressure acting on the wheel cylinders, thus controlling braking force.

DTC Code DTC Detection Condition Trouble Area
C0226 An open or short circuit in the SFRH or SFRR circuit continues for 0.05 seconds or more.
·

SFRH or SFRR circuit

·

Master cylinder solenoid


C0236 An open or short circuit in the SFLH or SFLR circuit continues for 0.05 seconds or more.
·

SFLH or SFLR circuit

·

Master cylinder solenoid


C0246 An open or short circuit in the SRRH or SRRR circuit continues for 0.05 seconds or more.
·

SRRH or SRRR circuit

·

Master cylinder solenoid


C0256 An open or short circuit in the SRLH or SRLR circuit continues for 0.05 seconds or more.
·

SRLH or SRLR circuit

·

Master cylinder solenoid


C1225 An open or short circuit in the SMCF circuit continues for 0.05 seconds or more.
·

SMCF circuit

·

Master cylinder solenoid


C1226 An open or short circuit in the SREA circuit continues for 0.05 seconds or more.
·

SREA circuit

·

Master cylinder solenoid


C1227 An open or short circuit in the SREC circuit continues for 0.05 seconds or more.
·

SREC circuit

·

Master cylinder solenoid


C1228 An open or short circuit in the STR circuit continues for 0.05 seconds or more.
·

STR circuit

·

Master cylinder solenoid



WIRING DIAGRAM

C220139E18
0.594,1.427 1.552,1.646 0.958,0.219 10 false ABS NO. 2 1.792,1.01 2.063,1.188 0.271,0.177 10 false 31 1.76,1.208 2.094,1.406 0.333,0.198 10 false A6 3.667,0.531 4.958,0.802 1.292,0.271 10 false Skid Control ECU 3.823,1.167 4.813,1.406 0.99,0.24 10 false Solenoid Relay 5.99,1.615 6.344,1.823 0.354,0.208 10 false STR 5.927,2.167 6.448,2.354 0.521,0.188 10 false SREC 5.917,2.667 6.438,2.854 0.521,0.188 10 false SFRH 5.948,3.167 6.396,3.354 0.448,0.188 10 false SFLH 5.948,3.656 6.396,3.844 0.448,0.188 10 false SRRH 5.938,4.167 6.385,4.354 0.448,0.188 10 false SRLH 5.938,4.667 6.385,4.854 0.448,0.188 10 false SFRR 5.938,5.656 6.385,5.844 0.448,0.188 10 false SRRR 5.938,6.156 6.385,6.344 0.448,0.188 10 false SRLR 5.948,6.646 6.396,6.833 0.448,0.188 10 false SREA 5.948,5.156 6.396,5.344 0.448,0.188 10 false SFLR 5.958,7.146 6.406,7.333 0.448,0.188 10 false SMCF 2.146,1.354 2.563,1.563 0.417,0.208 10 false +BS 1.76,5.083 2.094,5.281 0.333,0.198 10 false A6 1.771,5.865 2.104,6.063 0.333,0.198 10 false A6 1.76,6.656 2.094,6.854 0.333,0.198 10 false A7 1.823,4.865 1.979,5.042 0.156,0.177 10 false 1 1.792,5.667 1.979,5.844 0.188,0.177 10 false 32 1.823,6.448 1.979,6.625 0.156,0.177 10 false 4 0.24,3.292 1.104,3.573 0.865,0.281 10 false from Battery 2.104,5.104 2.646,5.344 0.542,0.24 10 false GND1 2.094,5.875 2.635,6.115 0.542,0.24 10 false GND2 2.104,6.667 2.646,6.906 0.542,0.24 10 false GND3 4.531,8.292 6.219,8.542 1.688,0.25 10 false Master Cylinder Solenoid

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are stored when a problem is detected in the master cylinder solenoid.

The solenoid circuit is in the master cylinder solenoid.

Therefore, solenoid circuit inspections and solenoid unit inspections cannot be performed. Be sure to check if any DTC is output before replacing the master cylinder solenoid.



b.

Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.


c.

Check if the same DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE MASTER CYLINDER SOLENOID

B