Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Steering angle sensor signals are sent to the skid control ECU via the CAN communication system. When there is a malfunction in the CAN communication system, it is detected by the steering angle sensor zero point malfunction diagnostic function.

DTC Code DTC Detection Condition Trouble Area
C1432 A steering angle sensor power supply malfunction signal is received from the steering angle sensor.
·

ECU-B fuse

·

ECU-IG NO. 1 fuse

·

Steering angle sensor power supply

·

Steering angle sensor (Spiral cable sub-assembly)



WIRING DIAGRAM

C200080E35
3.938,0.813 4.875,1.146 0.938,0.333 10 false from Battery 3.938,1.458 4.979,1.719 1.042,0.26 10 false from IG Circuit 0.875,0.823 1.26,1.031 0.385,0.208 10 false BAT 1,1.448 1.323,1.667 0.323,0.219 10 false IG 0.854,1.792 1.219,1.979 0.365,0.188 10 false ESS 1.302,0.677 1.542,0.875 0.24,0.198 10 false 6 1.302,1.365 1.521,1.563 0.219,0.198 10 false 5 1.323,1.646 1.5,1.802 0.177,0.156 10 false 2 0.198,2.563 3.542,2.885 3.344,0.323 10 false Steering Angle Sensor (Spiral Cable Sub-assembly) 0.813,3.469 2.75,3.667 1.938,0.198 10 false : CAN Communication System 5.479,2.281 7.063,2.677 1.583,0.396 10 false Master Cylinder Solenoid (Skid Control ECU) 5.49,2.125 5.698,2.323 0.208,0.198 10 false A6 0.208,2.365 0.688,2.625 0.479,0.26 10 false F19 2.073,1.615 3.083,1.865 1.01,0.25 10 false ECU-IG NO. 1 2.26,0.969 2.823,1.229 0.563,0.26 10 false ECU-B

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering angle sensor from the spiral cable sub-assembly.

·

When replacing the spiral cable sub-assembly, confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When DTC U0073, U0123, U0124 and/or U0126 is output together with DTC C1432, inspect and repair the trouble areas indicated by DTC U0073, U0123, U0124 and/or U0126 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073).

·

When the speed sensor or the yaw rate and acceleration sensor has trouble, DTCs for the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (IG, BAT)
a.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


b.

Disconnect the F19 steering angle sensor connector.


c.
U149966E03
2.031,1.385 1.677,1.885 1.677,1.885 1.469,1.885 false 2.281,1.198 2.646,0.344 2.646,0.344 2.75,0.344 false 0.125,0.115 0.344,0.333 0.219,0.219 10 false *a 2.823,0.26 3.167,0.469 0.344,0.208 10 false BAT 1.26,1.802 1.635,2.01 0.375,0.208 10 false IG 0.333,1.063 0.667,1.271 0.333,0.208 10 false F19

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F19-5 (IG) - Body ground Ignition switch ON 11 to 14 V
F19-6 (BAT) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Steering Angle Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the F19 steering angle sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F19-2 (ESS) - Body ground Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)