Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2009.08–2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the skid control ECU, the relay contact turns on and the stop light comes on.

DTC Code DTC Detection Condition Trouble Area
C1380 Either condition is met:
·

When the voltage at the IG1 terminal is between 10 V and 14 V, the stop light driving output (STPO) is on, and a signal has not been input to the STP terminal for 5 seconds or more.

·

When the voltage at the IG1 terminal is between 10 V and 14 V, the stop light driving output (STPO) is off, and the input signal at the STP terminal is different from the input signal at the STP2 terminal for 5 seconds or more.


·

STOP fuse

·

Harness or connector

·

Stop light control relay (STOP LP)

·

Master cylinder solenoid (Skid control ECU)



WIRING DIAGRAM

C212552E08
1.083,0.542 1.615,0.74 0.531,0.198 10 false STOP 5.958,1.354 6.469,1.573 0.51,0.219 10 false STP2 5.948,3.865 6.354,4.063 0.406,0.198 10 false STPO 2.594,1.865 3.792,2.063 1.198,0.198 10 false Stop Light Switch 2.479,0.396 3.5,0.646 1.021,0.25 10 false from Battery 2.5,2.5 3.5,2.719 1,0.219 10 false from IG Circuit 2.823,4.208 3.51,4.417 0.688,0.208 10 false STOP LP 2.271,5.26 3.25,5.469 0.979,0.208 10 false to Stop Lights 5.958,4.875 6.271,5.135 0.313,0.26 10 false STP 5.698,4.688 5.865,4.885 0.167,0.198 10 false 7 5.615,3.719 5.927,3.906 0.313,0.188 10 false 16 5.656,1.24 5.917,1.458 0.26,0.219 10 false 45 5.313,5.51 6.917,5.875 1.604,0.365 10 false Master Cylinder Solenoid (Skid Control ECU) 3.719,3.094 3.865,3.292 0.146,0.198 10 false 4 2.542,3.271 2.719,3.49 0.177,0.219 10 false 3 3.719,3.406 3.865,3.604 0.146,0.198 10 false 5 3.729,3.729 3.885,3.958 0.156,0.229 10 false 2 2.542,3.74 2.688,3.958 0.146,0.219 10 false 1 3.698,1.229 3.875,1.438 0.177,0.208 10 false 1 2.542,1.229 2.677,1.427 0.135,0.198 10 false 2 5.323,5.344 5.573,5.542 0.25,0.198 10 false A6 2.594,1.688 2.802,1.854 0.208,0.167 10 false A4

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425).


PROCEDURE

1.CHECK STOP LIGHT SWITCH OPERATION
a.

Check that the stop light comes on when the brake pedal is depressed and goes off when the brake pedal is released.

OK:

Stop light switch function is normal.




OK

2.CHECK TERMINAL VOLTAGE (STP)

NG

10.INSPECT STOP LP RELAY
2.CHECK TERMINAL VOLTAGE (STP)
a.

Disconnect the A6 skid control ECU connector.


b.
U180898E02
1.667,1.135 2.438,0.677 true 0.135,0.052 0.427,0.271 0.292,0.219 10 false *a 2.521,0.552 2.917,0.813 0.396,0.26 10 false STP 0.177,1.042 0.469,1.26 0.292,0.219 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

3.CHECK TERMINAL VOLTAGE (STP2)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TERMINAL VOLTAGE (STP2)
a.

Disconnect the A6 skid control ECU connector.


b.
U180899E02
2.531,1.542 2.531,1.875 true 0.125,0.052 0.406,0.271 0.281,0.219 10 false *a 2.385,1.896 2.792,2.063 0.406,0.167 10 false STP2 0.188,0.958 0.396,1.125 0.208,0.167 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-45 (STP2) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (STOP LIGHT RELAY)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light control (STOP LP) relay Relay ON/OFF Observe the stop light (does not come on for 2 to 5 seconds).


f.

Check the operation of the stop light when operating it with the intelligent tester.


OK:

The stop light turns on or off in accordance with the intelligent tester.



OK

5.RECONFIRM DTC

NG

6.CHECK TERMINAL VOLTAGE (STOP LP RELAY POWER SOURCE TERMINAL)
5.RECONFIRM DTC

b.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE MASTER CYLINDER SOLENOID

B

6.CHECK TERMINAL VOLTAGE (STOP LP RELAY POWER SOURCE TERMINAL)
a.

Remove the STOP LP relay from the engine room relay block.


b.
C215181E02
1.899,0 2.082,0.211 0.184,0.211 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1 - Body ground Ignition switch ON 8 to 14 V
5 - Body ground Always 11 to 14 V


Text in Illustration
*a Component without STOP LP Relay
(Engine Room Relay Block)



OK

7.INSPECT STOP LP RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT STOP LP RELAY
a.

Remove the STOP LP relay from the engine room relay block.


b.
C173370E02
0.068,0 0.335,0.269 0.267,0.269 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 10 kΩ or higher
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 Below 1 Ω
3 - 5 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 Below 1 Ω
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 10 kΩ or higher


Text in Illustration
*1 STOP LP relay



OK

8.CHECK TERMINAL VOLTAGE (STPO)

NG

REPLACE STOP LP RELAY

8.CHECK TERMINAL VOLTAGE (STPO)
a.

Disconnect the A6 skid control ECU connector.


b.
U180900E01
0.128,0.038 0.336,0.231 0.208,0.193 10 *a 2.896,0.651 3.322,0.828 0.427,0.177 10 STPO 2.655,1.15 2.861,0.78 false 0.223,0.793 0.439,0.986 0.216,0.193 10 A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A6-16 (STPO) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

9.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE MASTER CYLINDER SOLENOID

B

10.INSPECT STOP LP RELAY
a.

Remove the STOP LP relay from the engine room relay block.


b.
C173370E02
0.068,0 0.335,0.269 0.267,0.269 10 *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 4 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 10 kΩ or higher
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 Below 1 Ω
3 - 5 Battery positive voltage is applied to terminal 1 and battery negative voltage is applied to terminal 2 Below 1 Ω
Battery positive voltage is not applied to terminal 1 and battery negative voltage is not applied to terminal 2 10 kΩ or higher


Text in Illustration
*1 STOP LP relay



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

NG

REPLACE STOP LP RELAY