Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The master cylinder solenoid (skid control ECU) inputs stop light switch signals and the brake operation condition.

The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open circuit in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).

DTC Code DTC Detection Condition Trouble Area
C1425 When the IG1 terminal voltage is between 9.5 and 17.4 V and the skid control ECU STPO terminal output is off, an open in the stop light switch circuit continues for 3 seconds or more.
·

STOP fuse

·

Stop light switch

·

Stop light switch circuit

·

Master cylinder solenoid (skid control ECU)



CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK STOP LIGHT SWITCH OPERATION
a.

Check that the stop light comes on when the brake pedal is depressed and goes off when the brake pedal is released.

OK:

Stop light switch function is normal.




OK

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)

NG

GO TO LIGHTING SYSTEM (PROBLEM SYMPTOMS TABLE)

2.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.


HINT:

While checking the Data List, if the display changes when the wire harness or connector is jiggled, vibrated, etc., there may be a connection problem with the connector or an intermittent open circuit.




OK

NG

3.CHECK TERMINAL VOLTAGE (STP)
3.CHECK TERMINAL VOLTAGE (STP)
a.

Disconnect the A6 skid control ECU connector.


b.
U180898E02
1.667,1.135 2.438,0.677 true 0.135,0.052 0.427,0.271 0.292,0.219 10 false *a 2.521,0.552 2.917,0.813 0.396,0.26 10 false STP 0.177,1.042 0.469,1.26 0.292,0.219 10 false A6

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

B

REPLACE MASTER CYLINDER SOLENOID