Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2009.08–2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1437  Lost Communication with ECM  


DESCRIPTION

The skid control ECU receives signals from the ECM via the CAN communication system.

DTC Code DTC Detection Condition Trouble Area
C1437 When the IG1 terminal voltage is 10 V or higher and the vehicle speed is 15 km/h (9 mph) or more, data cannot be sent from the ECM for 2 seconds or more.
·

Engine control system

·

CAN communication system

·

Master cylinder solenoid (Skid control ECU)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
EFI Communication Open EFI communication open detection/ Error or Normal Normal -

OK:

Normal (there are no momentary interruptions).


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.RECONFIRM DTC

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - ECM)
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.


e.

Check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1437 is not output A
DTC C1437 is output B
CAN communication system DTC is output C



A

B

GO TO ENGINE CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - ECM)
a.

Turn the ignition switch off.


b.

Repair or replace the harness or connector.


c.

Check for any momentary interruption between the skid control ECU and ECM (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).


d.

Check that there is no momentary interruption.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 15 km/h (9 mph) or more for 10 seconds or more.


e.

Check that no CAN communication system DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1437 is not output A
DTC C1437 is output B
CAN communication system DTC is output C



A

END

B

REPLACE MASTER CYLINDER SOLENOID

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)