Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2009.08–2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1253  Pump Motor Relay  


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.

DTC Code DTC Detection Condition Trouble Area
C1253 There is a motor system circuit (motor input circuit) malfunction.
·

ABS NO. 1 fuse

·

Motor relay circuit

·

Master cylinder solenoid (Skid control ECU)



WIRING DIAGRAM

C173280E29
4.135,5.365 6.51,5.74 2.375,0.375 10 false Hydraulic Brake Booster Assembly 4.833,4.885 5.719,5.104 0.885,0.219 10 false Pump Motor 5.198,1.635 6.052,1.854 0.854,0.219 10 false Motor Relay 4.969,0.792 6.156,1.01 1.188,0.219 10 false Skid Control ECU 3.177,1.677 3.458,1.865 0.281,0.188 10 false A6 3.24,1.479 3.417,1.635 0.177,0.156 10 false 2 3.542,1.583 4.052,1.833 0.51,0.25 10 false +BM1 3.177,2.198 3.49,2.427 0.313,0.229 10 false A7 3.24,1.99 3.417,2.146 0.177,0.156 10 false 2 3.542,2.104 4.021,2.26 0.479,0.156 10 false +BM2 3.177,2.677 3.5,2.875 0.323,0.198 10 false A6 3.229,2.479 3.406,2.635 0.177,0.156 10 false 1 3.531,2.583 4.031,2.802 0.5,0.219 10 false GND1 3.177,3.188 3.5,3.365 0.323,0.177 10 false A6 3.208,2.979 3.438,3.208 0.229,0.229 10 false 32 3.531,3.083 4.052,3.354 0.521,0.271 10 false GND2 3.177,3.75 3.49,3.979 0.313,0.229 10 false A7 0.24,4.208 1.177,4.49 0.938,0.281 10 false from Battery 0.906,2.385 1.708,2.635 0.802,0.25 10 false ABS NO. 1 3.219,3.531 3.396,3.688 0.177,0.156 10 false 4 3.531,3.635 4.021,3.844 0.49,0.208 10 false GND3 4.552,0.25 6.167,0.469 1.615,0.219 10 false Master Cylinder Solenoid 4.906,3.917 5.365,4.135 0.458,0.219 10 false M+1 6.083,3.917 6.542,4.135 0.458,0.219 10 false M+2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MOTOR RELAY)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Start the engine.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay Motor relay Relay ON/OFF An operating sound of the motor can be heard.


g.

Check the operating sound of the motor individually when operating it with the intelligent tester.

OK:

An operating sound of the motor can be heard.




OK

2.RECONFIRM DTC

NG

3.CHECK TERMINAL VOLTAGE (+BM1, +BM2)
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Depress the brake pedal more than 40 times.


d.

Turn the ignition switch to ON.


e.

Wait until the pump motor stops.


f.

Depress the brake pedal several times until the pump motor turns on. (Procedure A)


g.

Wait until the pump stops. (Procedure B)


h.

Repeat the above steps (procedure A and B) 3 more times.


i.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE MASTER CYLINDER SOLENOID

B

3.CHECK TERMINAL VOLTAGE (+BM1, +BM2)
a.

Disconnect the A6 and A7 skid control ECU connectors.


b.
U180809E01
0.151,2.405 0.715,2.625 0.563,0.221 10 +BM1 2.62,3.43 3.184,3.651 0.563,0.221 10 +BM2 0.895,1.419 0.382,2.395 false 1.861,3.844 2.583,3.552 false 0.044,0.086 0.273,0.398 0.228,0.312 10 *a 1.624,0.591 1.897,0.754 0.274,0.163 10 A6 1.612,3.129 1.886,3.292 0.274,0.163 10 A7

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-2 (+BM1) - Body ground Always 11 to 14 V
A7-2 (+BM2) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

4.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Depress the brake pedal more than 40 times.


d.

Turn the ignition switch to ON.


e.

Wait until the pump motor stops.


f.

Depress the brake pedal several times until the pump motor turns on. (Procedure A)


g.

Wait until the pump stops. (Procedure B)


h.

Repeat the above steps (procedure A and B) 3 more times.


i.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE MASTER CYLINDER SOLENOID

B