Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2009.08–2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1254  Pressure Sensor or Switch  


DESCRIPTION

The accumulator pressure sensor is connected to the skid control ECU in the master cylinder solenoid.

C173281E21
2.719,3.167 4.406,3.458 1.688,0.292 10 false Master Cylinder Solenoid 0.094,3.552 3.875,3.813 3.781,0.26 10 false VACC: Accumulator Pressure Sensor Power Supply Output 0.083,3.906 3.865,4.167 3.781,0.26 10 false PACC: Accumulator Pressure Sensor Signal Input 0.083,4.271 3.865,4.531 3.781,0.26 10 false ACCGND: Accumulator Pressure Sensor Ground 1.844,0.854 2.219,1.104 0.375,0.25 10 false IG1 1.844,1.917 2.219,2.167 0.375,0.25 10 false GND 2.781,0.854 3.24,1.104 0.458,0.25 10 false VACC 2.76,1.375 3.219,1.625 0.458,0.25 10 false PACC 2.573,1.896 3.25,2.146 0.677,0.25 10 false ACCGND 4.302,0.844 4.76,1.094 0.458,0.25 10 false VACC 4.313,1.365 4.771,1.615 0.458,0.25 10 false PACC 4.292,1.896 4.969,2.146 0.677,0.25 10 false ACCGND 1.906,2.292 3.167,2.542 1.26,0.25 10 false Skid Control ECU 4.25,2.26 5.427,2.708 1.177,0.448 10 false Accumulator Pressure Sensor

DTC Code DTC Detection Condition Trouble Area
C1254 There is an accumulator pressure sensor malfunction (the fluid pressure does not change when the pump operates or when the brake is applied). Master cylinder solenoid (Accumulator pressure sensor)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCUMULATOR SENSOR)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Depress the brake pedal more than 40 times.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V 3.58 to 5 V If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.


g.

Check the accumulator output value.

Result
Result Proceed to
Output value is within "Normal Condition" range A
Output value is out of "Normal Condition" range B
Output value is constant regardless of pump operation



A

2.RECONFIRM DTC

B

REPLACE MASTER CYLINDER SOLENOID

2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Depress the brake pedal more than 40 times.


d.

Turn the ignition switch to ON.


e.

Wait until the pump motor stops.


f.

Wait for 15 minutes.


g.

Depress the brake pedal and release it.


h.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE MASTER CYLINDER SOLENOID

B