Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2009.08–2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1453  Reservoir Level Switch Disconnected  C1454  Reservoir Level Low  


DESCRIPTION

The brake fluid level warning switch sends the appropriate signal to the skid control ECU when the brake fluid level drops.

DTC Code DTC Detection Condition Trouble Area
C1453 With the ECU terminal IG1 voltage at 10 to 14 V, an open in the brake fluid level warning switch circuit continues for 2 seconds or more.
·

Brake fluid level

·

Brake fluid level warning switch (Brake master cylinder reservoir assembly)

·

Harness or connector

·

Master cylinder solenoid (Skid control ECU)


C1454 The fluid level of the reservoir is LOW for 40 seconds after the ignition switch is turned to ON, or for 7 seconds during pump motor operation.

WIRING DIAGRAM

C361644E01
1.26,0.625 1.417,0.823 0.156,0.198 10 false 1 3.396,0.635 3.552,0.833 0.156,0.198 10 false 2 4.385,0.635 4.542,0.833 0.156,0.198 10 false 41 4.573,1.396 4.927,1.625 0.354,0.229 10 false A6 4.667,0.771 5.104,1 0.438,0.229 10 false LBL 1.417,1.448 1.771,1.677 0.354,0.229 10 false A8 1.406,1.625 3.458,2.167 2.052,0.542 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir assembly) 4.563,1.573 6.167,1.948 1.604,0.375 10 false Master Cylinder Solenoid (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK BRAKE FLUID LEVEL
a.

Turn the ignition switch off.


b.

Depress the brake pedal 40 times or more (until the pedal reaction feels light and pedal stroke becomes longer).


c.

Check the amount of fluid in the brake reservoir.

HINT:

When the ignition switch is turned to ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 5 mm (0.196 in.) from the level when the ignition switch is off (normal).


OK:

Brake fluid level is normal.




OK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

CHECK AND REPAIR BRAKE FLUID LEAK

2.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.

Disconnect the A8 brake fluid level warning switch connector.


b.
C217215E05
0.12,0.111 0.297,0.288 0.177,0.177 10 *a

Measure the resistance according to the value(s) in the table below.

HINT:

A float is placed inside the reservoir. Its position can be changed by increasing/decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Float UP (Switch off) 1.9 to 2.1 kΩ
Float DOWN (Switch on) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch)

HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.




OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the A6 skid control ECU connector.


b.

Disconnect the A8 brake fluid level warning switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-41 (LBL) - A8-2 Always Below 1 Ω
A6-41 (LBL) - Body ground Always 10 kΩ or higher
A8-1 - Body ground Always Below 1 Ω




OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine and idle it for approximately 40 seconds.


d.

Check if the same DTCs are output.

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE MASTER CYLINDER SOLENOID

B