Power is supplied to the radio receiver assembly and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
Check if the illumination for the radio receiver assembly, steering pad switch, glove box or other parts (hazard switch, transmission control switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.
| Result | Proceed to |
|---|---|
| Illumination comes on for all components except steering pad switch. | A |
| Illumination comes on for all components except radio receiver assembly. | B |
| No illumination comes on (radio receiver, hazard switch, glove box, etc.). | C |
| Illumination comes on for all components except steering pad switch and radio receiver assembly. | D |
A
B
C
D
Disconnect the F23 spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F23-12 (IL+2) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
OK
NG
Remove the steering pad switch assembly connector (See page Steering>STEERING COLUMN>STEERING WHEEL>REMOVAL).
Connect the positive (+) lead of the battery to terminal 5 (IL+2) and the negative (-) lead of the battery to terminal 8 (EAU) of the steering pad switch assembly connector.
Check if the illumination for the steering pad switch assembly comes on.
Illumination for the steering pad switch assembly comes on.
OK
NG
Remove the spiral cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 8 (EAU) - 4 (EAU) | Spiral cable is turned 2.5 rotations counterclockwise | Below 1 Ω |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise | ||
| 5 (IL+2) - 12 (IL+2) | Spiral cable is turned 2.5 rotations counterclockwise | |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise |
| *a | Steering Pad Switch Assembly Side |
| *b | Vehicle Side |
The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read Precaution in the SRS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).
OK
NG
Disconnect the G9 radio receiver assembly connector.
Disconnect the F23 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G9-6 (SWG) - F23-4 (EAU) | Always | Below 1 Ω |
| G9-6 (SWG) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the G6 radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G6-10 (ILL+) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
| *a | Front view of wire harness connector
(to Radio Receiver Assembly) |
OK
NG
Disconnect the G5 radio receiver assembly connector.
Disconnect the F14 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G5-5 (ILL-) - F14-11 (ILL-) | Always | Below 1 Ω |
| G5-5 (ILL-) - Body ground | Always | 10 kΩ or higher |
OK
NG