Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2009.08–2013.08
RM1440E _56 Audio / Visual / Telematics _056150 AUDIO / VIDEO _0274026 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  01-DC  Transmission Error  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
01-DC Transmission to the component shown by the sub-code failed (Detecting this DTC does not always mean actual failure). If the same sub-code is recorded in other components, check harness for power supply and communication system of all components shown by code

HINT:

This code may be stored if the engine is started and idled for 60 seconds and then the ignition switch is turned to the start position again.


NOTICE:
·

Before starting troubleshooting, be sure to clear DTCs to clear codes stored due to the reasons described in Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.

·

The radio receiver assembly is the master unit.

·

Be sure to clear and recheck DTCs after the inspection is completed to confirm that no DTCs are output.



CAUTION / NOTICE / HINT

NOTICE:

Be sure to read Description before performing the following procedures.


PROCEDURE

1.CHECK FOR DTC OF OTHER COMPONENTS
a.

Check if the component shown by the sub-code is displayed in the check result of the other components.

i.

Check if "01-DC" is output for the other components.


ii.

If "01-DC" is output for any other components, check if the same physical address is displayed.

HINT:

For the list of the components shown by sub-codes, refer to the table in the next step.


Result
Result Proceed to
"01-DC" is not output or the same physical address is not displayed A
"01-DC" is output and the same physical address is displayed B




A

2.CLEAR DTC

B

4.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE
2.CLEAR DTC
a.

Clear the DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).

HINT:

If "01-DC" is output for only one component, this may not indicate a malfunction.




NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs and check if the same trouble occurs again.

OK:

Malfunction disappears.




OK

NG

5.CHECK COMPONENT WHICH HAS STORED THIS CODE
4.IDENTIFY COMPONENT WHICH HAS STORED THIS CODE
a.

Enter the diagnostic mode.

E146440E32
1.052,0.813 1.323,1 0.271,0.188 10 false *1 1.052,1.354 1.344,1.542 0.292,0.188 10 false *1 1.052,1.875 1.323,2.063 0.271,0.188 10 false *1 1.042,2.344 1.313,2.531 0.271,0.188 10 false *1 1.052,3.333 1.323,3.521 0.271,0.188 10 false *1 0.448,0.698 0.802,0.885 0.354,0.188 10 false *1 4.104,2.583 4.375,2.771 0.271,0.188 10 false *1 4.115,3.063 4.385,3.25 0.271,0.188 10 false *1 4.104,3.625 4.375,3.813 0.271,0.188 10 false *1 4.104,4.146 4.375,4.333 0.271,0.188 10 false *1 4.115,5.24 4.385,5.427 0.271,0.188 10 false *1 4.104,6.146 4.375,6.333 0.271,0.188 10 false *1 3.115,4.5 3.385,4.688 0.271,0.188 10 false *1 4.823,6.156 5.146,6.344 0.323,0.188 10 false *2 4.823,5.208 5.177,5.396 0.354,0.188 10 false *2 4.802,4.146 5.135,4.333 0.333,0.188 10 false *2 4.792,3.625 5.146,3.813 0.354,0.188 10 false *2 4.802,3.073 5.135,3.26 0.333,0.188 10 false *2 4.802,2.583 5.135,2.771 0.333,0.188 10 false *2 6.26,2.479 6.594,2.667 0.333,0.188 10 false *2 1.771,3.344 2.146,3.531 0.375,0.188 10 false *2 1.771,2.323 2.073,2.51 0.302,0.188 10 false *2 1.76,1.875 2.104,2.063 0.344,0.188 10 false *2 1.771,1.344 2.104,1.531 0.333,0.188 10 false *2 1.771,0.802 2.073,0.99 0.302,0.188 10 false *2 2.427,0.677 2.719,0.865 0.292,0.188 10 false *2 3.302,1.917 3.646,2.104 0.344,0.188 10 false *3 2.948,2.313 3.292,2.5 0.344,0.188 10 false *4 0.115,5.417 1.844,5.594 1.729,0.177 10 false *1: SEEK TRACK DOWN 0.115,5.75 1.677,5.927 1.563,0.177 10 false *2: SEEK TRACK UP 0.115,6.094 2.49,6.26 2.375,0.167 10 false *3: PRESET SWITCH "channel 2" 0.115,6.438 2.49,6.604 2.375,0.167 10 false *4: PRESET SWITCH "channel 3" 5.74,3.635 6.063,3.802 0.323,0.167 10 false DTC 3.406,1.281 5.854,1.49 2.448,0.208 10 false Component which has stored this code 2.021,0.219 3.833,0.396 1.813,0.177 10 false Service Check Mode: 4.938,0.813 6.979,0.99 2.042,0.177 10 false Detailed Information Mode: 3.688,4.479 5.854,4.813 2.167,0.333 10 false Continues to display detailed information of the first code. 3.688,5.448 6.438,5.823 2.75,0.375 10 false Continues to display detailed information when more DTCs are output. 0.396,2.646 2.729,2.958 2.333,0.313 10 false Continues to display check result when more components are installed. 0.073,0.021 0.865,0.198 0.792,0.177 10 false Example:


b.

Press the preset switch "channel 3" to change to "Detailed Information Mode".


c.

Identify the component which has stored this code.

Component Table
Component Physical Address
Radio receiver assembly 190
Multi-media interface ECU 388


HINT:
·

"440 (stereo component amplifier)" is the component which has stored this code in the example shown in the illustration.

·

For details of the DTC display, refer to DTC Check/Clear (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).




NEXT

5.CHECK COMPONENT WHICH HAS STORED THIS CODE
5.CHECK COMPONENT WHICH HAS STORED THIS CODE
a.

Select the component which has stored this code.

Component Table
Component Proceed to
Radio receiver assembly Radio receiver communication error (See page (Click here))
Multi-media interface ECU Multi-media interface ECU communication error (See page (Click here))



NEXT

END