Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › from 2013.08
RM1440E _56 Audio / Visual / Telematics _056150 AUDIO / VIDEO _0274026 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code DTC Detection Condition Trouble Area
B1579 Telephone microphone signal is lost.
·

Map light assembly (Telephone microphone assembly)

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E353049E01
1.646,0.708 2.042,0.917 0.396,0.208 10 false SNS2 1.667,1.49 2.063,1.698 0.396,0.208 10 false MCO- 0.688,2 0.875,2.219 0.188,0.219 10 false U2 2.125,1.375 2.313,1.594 0.188,0.219 10 false 12 5.083,0.677 5.479,0.885 0.396,0.208 10 false SNS2 5.083,1.479 5.479,1.688 0.396,0.208 10 false MIN- 4.854,0.594 5.042,0.813 0.188,0.219 10 false 6 4.823,1.396 5.01,1.615 0.188,0.219 10 false 19 0.688,2.188 2.708,2.552 2.021,0.365 10 false Map Light Assembly (Telephone Microphone Assembly) 4.302,2.031 4.573,2.24 0.271,0.208 10 false G29 4.333,2.208 6.698,2.417 2.365,0.208 10 false Radio and Display Receiver Assembly 2.125,0.573 2.313,0.792 0.188,0.219 10 false 15

PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
U181080E02
2.073,1.99 2.563,2.771 true 2.531,2.802 2.896,2.979 0.365,0.177 10 false MIN- 1.583,0.594 1.917,0.75 0.333,0.156 10 false G29 0.229,0.135 0.5,0.375 0.271,0.24 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G29-19 (MIN-) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the G29 radio and display receiver assembly connector.


b.

Disconnect the U2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G29-6 (SNS2) - U2-15 (SNS2) Always Below 1 Ω
G29-19 (MIN-) - U2-12 (MCO-) Always Below 1 Ω
G29-6 (SNS2) - Body ground Always 10 kΩ or higher
G29-19 (MIN-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.
U150464E04
1.781,1.396 1.406,1.667 true 2.104,1.385 2.479,1.677 true 1.615,0.365 1.896,0.542 0.281,0.177 10 false U2 0.156,0.063 0.354,0.26 0.198,0.198 10 false *a 1.177,1.708 1.594,1.906 0.417,0.198 10 false SNS2 2.396,1.708 2.823,1.906 0.427,0.198 10 false MCO-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U2-15 (SNS2) - U2-12 (MCO-) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
4.REPLACE TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL).



c.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)