Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU
RM1440E _57 Power Source / Network _056153 POWER DISTRIBUTION _0274051 MAIN BODY ECU A

POWER DISTRIBUTION  MAIN BODY ECU  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 89221 1.INSTALL MULTIPLEX NETWORK BODY ECU

NOTICE:
·

Make sure that no foreign objects contact the connecting surfaces.

·

Do not touch the ECU connector.



a.
B195951E14
2.854,1.49 2.521,1.927 false 2.354,2.042 2.885,2.677 true 0.26,1.313 0.635,1.51 0.375,0.198 10 false 20° 2.875,1.354 3.083,1.531 0.208,0.177 10 false *1 2.938,2.656 3.146,2.833 0.208,0.177 10 false *2

Insert the multiplex network body ECU until it contacts the housing sidewall of the guide part as shown in the illustration.

Text in Illustration
*1 Housing Sidewall
*2 Guide Part

HINT:

Be sure to maintain an angle of 20° or more as shown in the illustration.



b.
B197889E12
2.635,2.521 2.844,2.698 true 2.615,1.969 2.854,1.75 false 2.354,1.948 2.688,1.333 true 2.885,1.615 3.135,1.802 0.25,0.188 10 false *1 2.729,1.167 2.979,1.354 0.25,0.188 10 false *2 2.938,2.677 3.188,2.865 0.25,0.188 10 false *3

Slide the guide of the multiplex network body ECU along the housing sidewall toward the junction block fuses as shown in the illustration.

Text in Illustration
*1 Housing Sidewall
*2 Guide Part
*3 Junction Block Fuse


c.
B195952E10
2.521,1.094 2.854,0.719 true 2.885,0.604 3.146,0.781 0.26,0.177 10 false *1

Slide the multiplex network body ECU so that it contacts side A as shown in the illustration.

Text in Illustration
*1 Side A

NOTICE:

Do not apply excessive force to the multiplex network body ECU.



d.
B195954E08
2.813,1.25 3.094,0.948 false 3.125,0.792 3.313,0.948 0.188,0.156 10 false *1

With the multiplex network body ECU contacting side A of the junction block (point of rotation), rotate it downward as shown in the illustration.

Text in Illustration
*1 Side A Contact Portion


e.
E183108E02
2.042,1.208 2.635,2.042 true 2.583,2.073 2.781,2.24 0.198,0.167 10 false *1

Press the pushing area until the claw attaches to install the multiplex network body ECU.

Text in Illustration
*1 Pushing Area

NOTICE:
·

Make sure to press only the pushing area.

·

Confirm the engagement of the multiplex network body ECU and junction block by listening for a lock sound.

·

Do not apply excessive force to the multiplex network body ECU.



HINT:

If a lock sound cannot be heard, visually check the engagement of the lock part. The engagement can also be confirmed if the multiplex network body ECU and junction block are flush.



Hide 2.INSTALL DRIVER SIDE JUNCTION BLOCK ASSEMBLY

a.
E178382

Attach the claw to install the connector as shown in the illustration.

NOTICE:

Be sure to connect each connector securely.



b.
E178380

Attach the 2 claws to lock the connector lock as shown in the illustration.


c.
E178378

Attach the claw to connect the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



d.

Install the driver side junction block assembly with the bolt and 2 nuts.

Torque:
for bolt : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for nut : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
E353211E01
2.313,0.875 2.521,1.083 0.208,0.208 10 true (1) 2.375,1.49 2.583,1.698 0.208,0.208 10 true (1) 2.792,2.406 3,2.615 0.208,0.208 10 true (2)

Connect the connector labeled (2).

NOTICE:

Be sure to connect each connector securely.



f.

Connect the 2 connectors labeled (1) as shown in the illustration.

NOTICE:

Be sure to connect each connector securely.



g.

Connect the 3 connectors.

NOTICE:

Be sure to connect each connector securely.



Hide 55045 3.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55474C 4.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

Hide 67920 6.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 8.CHECK SRS WARNING LIGHT