Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2009.08–2016.12
RM1440E _57 Power Source / Network _056154 NETWORKING _0274052 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1273  Sliding Roof ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1273 No communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Sliding roof drive gear sub-assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

C217632E48
5.406,0.354 5.844,0.521 0.438,0.167 10 false MPX1 5.229,0.271 5.354,0.438 0.125,0.167 10 false 4 1.542,0.385 1.854,0.552 0.313,0.167 10 false LIN2 1.958,0.271 2.156,0.438 0.198,0.167 10 false 16 0.729,0.708 1.021,0.875 0.292,0.167 10 false A 0.719,0.875 2.385,1.292 1.667,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 5.417,0.781 5.667,0.948 0.25,0.167 10 false B 5.229,0.698 5.354,0.865 0.125,0.167 10 false 1 4.521,0.938 5.094,1.104 0.573,0.167 10 false S/ROOF 4.313,1.385 5.271,1.552 0.958,0.167 10 false ECU-IG NO. 2 3.188,0.781 3.979,0.948 0.792,0.167 10 false from Battery 2.604,1.219 3.979,1.385 1.375,0.167 10 false from IG1 No. 1 Relay 5.406,1.229 5.76,1.396 0.354,0.167 10 false IG 4.958,1.948 5.313,2.115 0.354,0.167 10 false S8 4.969,2.104 6.448,2.469 1.479,0.365 10 false Sliding Roof Drive Gear Sub-assembly 5.229,1.146 5.354,1.313 0.125,0.167 10 false 5 5.406,1.604 5.76,1.771 0.354,0.167 10 false E 5.229,1.521 5.354,1.688 0.125,0.167 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the sliding roof drive gear sub-assembly and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1273 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF DRIVE GEAR)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF DRIVE GEAR)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the S8 sliding roof drive gear sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - S8-4 (MPX1) Always Below 1 Ω
A-16 (LIN2) or S8-4 (MPX1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - BATTERY AND BODY GROUND)
a.
U150221E03
1.198,0.99 1.031,0.74 1.031,0.74 0.896,0.74 true 1.177,1.354 1.01,1.604 1.01,1.604 0.875,1.604 true 1.385,0.99 1.292,0.563 1.292,0.563 1.156,0.563 true 0.063,0.094 0.24,0.292 0.177,0.198 10 false *a 0.729,0.688 0.854,0.865 0.125,0.177 10 false B 0.667,1.531 0.854,1.708 0.188,0.177 10 false IG 2.708,1.083 2.948,1.26 0.24,0.177 10 false S8 0.99,0.5 1.115,0.656 0.125,0.156 10 false E

Disconnect the S8 sliding roof drive gear sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S8-2 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S8-1 (B) - Body ground Always 11 to 14 V
S8-5 (B) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Sliding Roof Drive Gear Sub-assembly)


OK

5.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
a.

Temporarily replace the sliding roof drive gear sub-assembly with a new or normally functioning one (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING>DISASSEMBLY).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1273 is not output.




OK

END (SLIDING ROOF DRIVE GEAR IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)