Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM1440E _57 Power Source / Network _056154 NETWORKING _0274052 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2322  Front Passenger Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2322 No communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Front power window regulator motor assembly RH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

C361639E03
1.469,0.406 1.813,0.583 0.344,0.177 10 false LIN2 1.979,0.26 2.198,0.448 0.219,0.188 10 false 16 5.146,0.24 5.26,0.417 0.115,0.177 10 false 9 5.146,0.667 5.281,0.854 0.135,0.188 10 false 2 5.146,1.125 5.281,1.313 0.135,0.188 10 false 1 0.667,1 0.865,1.177 0.198,0.177 10 false A 0.656,1.188 2.313,1.542 1.656,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 3.115,0.813 3.927,1.01 0.813,0.198 10 false from Battery 4.51,0.969 5.052,1.156 0.542,0.188 10 false DOOR P 5.417,0.385 5.719,0.563 0.302,0.177 10 false LIN 5.417,0.823 5.573,1 0.156,0.177 10 false B 5.417,1.26 5.792,1.448 0.375,0.188 10 false GND 4.563,1.875 4.729,2.052 0.167,0.177 10 false H2 4.583,2.083 6.552,2.479 1.969,0.396 10 false Front Power Window Regulator Motor Assembly RH

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2322 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR RH)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT POWER WINDOW REGULATOR MOTOR RH)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the H2 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - H2-9 (LIN) Always Below 1 Ω
A-16 (LIN2) or H2-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR RH - BATTERY AND BODY GROUND)
a.
U150223E03
1.531,0.99 1.313,0.708 1.313,0.708 1.177,0.708 true 1.896,1 2.125,0.719 2.125,0.719 2.26,0.719 true 0.042,0 0.219,0.198 0.177,0.198 10 false *a 2.344,0.625 2.49,0.802 0.146,0.177 10 false B 0.833,0.646 1.167,0.823 0.333,0.177 10 false GND 0.823,1.104 1.063,1.281 0.24,0.177 10 false H2

Disconnect the H2 front power window regulator motor assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H2-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H2-2 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly RH)


OK

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Temporarily replace the front power window regulator motor assembly RH with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2322 is not output.




OK

END (FRONT POWER WINDOW REGULATOR MOTOR RH IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)