Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2013.08
RM1440E _57 Power Source / Network _056154 NETWORKING _0274053 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

·

The main body ECU (multiplex network body ECU) stores this DTC when no signals can be received from the ECUs that are memorized as those connected to the CAN MS bus.

·

When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that are memorized as those connected to the CAN MS bus, the main body ECU (multiplex network body ECU) determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module.
·

MS bus circuit

·

Front power seat switch LH branch wire or connector

·

Main body ECU (multiplex network body ECU) main wire or connector

·

Combination meter assembly main wire or connector

·

Front power seat switch LH

·

Main body ECU (multiplex network body ECU)

·

Combination meter assembly

·

No. 2 junction connector



HINT:

For vehicles with seat position memory only.



WIRING DIAGRAM

C290754E04
2.771,0.573 2.969,0.75 0.198,0.177 10 false 12 2.76,0.208 2.906,0.385 0.146,0.177 10 false 1 6,0.198 6.438,0.354 0.438,0.156 10 false CANP 6,0.813 6.417,0.99 0.417,0.177 10 false CANN 4.823,1.302 5.302,1.479 0.479,0.177 10 false ECU-B 3.458,1.135 4.24,1.344 0.781,0.208 10 false from Battery 3.25,2.708 4.25,2.917 1,0.208 10 false from ACC Relay 2.958,2.167 4.24,2.385 1.281,0.219 10 false from IG1 No. 1 Relay 4.75,1.802 5.427,1.979 0.677,0.177 10 false D/L NO. 2 4.563,2.344 5.51,2.521 0.948,0.177 10 false ECU-IG NO. 2 4.896,2.885 5.25,3.063 0.354,0.177 10 false ACC 5.938,1.146 6.344,1.323 0.406,0.177 10 false BECU 5.938,1.635 6.292,1.813 0.354,0.177 10 false ALTB 5.969,2.167 6.198,2.344 0.229,0.177 10 false IG 5.948,2.708 6.281,2.885 0.333,0.177 10 false ACC 5.365,4.146 7.063,4.531 1.698,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.719,0.115 5.865,0.292 0.146,0.177 10 false 9 5.677,0.51 5.865,0.656 0.188,0.146 10 false 10 5.677,0.969 5.854,1.146 0.177,0.177 10 false 30 5.677,1.49 5.865,1.667 0.188,0.177 10 false 31 5.667,2 5.865,2.156 0.198,0.156 10 false 32 5.646,2.552 5.875,2.729 0.229,0.177 10 false 29 5.656,3.083 5.885,3.26 0.229,0.177 10 false 11 0.729,0.302 1.146,0.479 0.417,0.177 10 false CANP 0.719,0.688 1.146,0.865 0.427,0.177 10 false CANN 1.948,0.583 2.115,0.75 0.167,0.167 10 false 14 2.021,0.198 2.135,0.375 0.115,0.177 10 false 3 0.115,1.302 1.229,1.729 1.115,0.427 10 false Front Power Seat Switch LH 0.146,3.573 0.427,3.771 0.281,0.198 10 false F14 5.635,0.313 5.885,0.469 0.25,0.156 10 false F10 5.635,0.688 5.906,0.854 0.271,0.167 10 false F10 5.625,3.677 5.896,3.854 0.271,0.177 10 false F10 5.708,1.135 5.854,1.302 0.146,0.167 10 false A 5.698,1.646 5.833,1.813 0.135,0.167 10 false A 5.698,2.188 5.854,2.354 0.156,0.167 10 false A 5.688,2.719 5.844,2.875 0.156,0.156 10 false A 5.958,3.26 6.396,3.438 0.438,0.177 10 false GND1 5.948,3.677 6.385,3.854 0.438,0.177 10 false GND2 5.688,3.26 5.833,3.417 0.146,0.156 10 false A 5.698,3.49 5.802,3.667 0.104,0.177 10 false 3 0.104,1.083 0.406,1.26 0.302,0.177 10 false b19 1.677,3.458 1.979,3.635 0.302,0.177 10 false F82 1.198,0.563 1.333,0.74 0.135,0.177 10 false 7 1.198,0.198 1.344,0.375 0.146,0.177 10 false 8 1.938,3.052 2.156,3.229 0.219,0.177 10 false 13 1.99,2.646 2.125,2.833 0.135,0.188 10 false 2 1.667,3.667 3.26,3.875 1.594,0.208 10 false No. 2 Junction Connector 1.198,3.052 1.385,3.229 0.188,0.177 10 false 24 1.188,2.656 1.396,2.833 0.208,0.177 10 false 23 0.646,2.677 1.073,2.844 0.427,0.167 10 false MSCH 0.677,3.271 1.083,3.448 0.406,0.177 10 false MSCL 0.125,3.802 1.333,4.25 1.208,0.448 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
2.CHECK FOR CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)
a.
U150382E03
1.625,2.51 1.5,2.188 1.5,2.188 1.417,2.188 true 2.219,2.958 2.427,3.125 2.427,3.125 2.51,3.125 true 1.813,1.24 2.594,1.76 2.594,1.76 2.677,1.76 true 1.885,1.188 2.594,0.458 2.594,0.458 2.677,0.458 true 2.74,0.385 3.167,0.563 0.427,0.177 10 false CANP 2.729,1.688 3.229,1.865 0.5,0.177 10 false CANN 1.542,0.198 1.844,0.375 0.302,0.177 10 false F10 0.458,2.667 0.781,2.844 0.323,0.177 10 false F13 0.073,0.042 0.281,0.219 0.208,0.177 10 false *a 0.073,2.031 0.281,2.208 0.208,0.177 10 false *b 1.135,2.104 1.375,2.281 0.24,0.177 10 false CG 2.563,3.031 3,3.208 0.438,0.177 10 false BAT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
F10-9 (CANP) - F10-10 (CANN) Ignition switch off 54 to 69 Ω Below 54 Ω: Short in line
Higher than 69 Ω: Open in CAN main bus line
F10-9 (CANP) - F13-16 (BAT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
F10-10 (CANN) - F13-16 (BAT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
F10-9 (CANP) - F13-4 (CG) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
F10-10 (CANN) - F13-4 (CG) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))
*b Front view of DLC3

Result
Result Proceed to
NG
- Open in CAN main bus line
A
NG
- Short in line
- +B short
- Ground short
B
OK C



A

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

B

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH)

C

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - BATTERY AND GROUND)
3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U180932E02
2.208,0.948 2.604,0.531 2.604,0.531 2.688,0.531 true 2.208,1.177 2.604,1.563 2.604,1.563 2.688,1.563 true 2.75,0.469 3.188,0.646 0.438,0.177 10 false MSCH 0.531,0.875 0.823,1.052 0.292,0.177 10 false F82 0.063,0.063 0.271,0.24 0.208,0.177 10 false *a 2.74,1.49 3.177,1.667 0.438,0.177 10 false MSCL

Disconnect the F82 No. 2 junction connector connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F82-2 (MSCH) - F82-13 (MSCL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.
U180933E02
2.323,0.958 2.719,0.521 2.719,0.521 2.802,0.521 true 2.323,1.177 2.719,1.563 2.719,1.563 2.802,1.563 true 2.854,0.438 3.292,0.615 0.438,0.177 10 false CANP 0.521,0.865 0.813,1.042 0.292,0.177 10 false F82 0.063,0.01 0.271,0.188 0.208,0.177 10 false *a 2.865,1.469 3.302,1.646 0.438,0.177 10 false CANN

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F82-1 (CANP) - F82-12 (CANN) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR

NG

7.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the F82 No. 2 junction connector connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
a.
U149938E01
0.205,0.575 0.535,0.758 0.330,0.183 10 F14 1.724,0.475 2.271,0.657 0.547,0.183 10 MSCL 1.474,0.203 1.907,0.359 0.433,0.156 10 MSCH 0.084,0.063 0.413,0.245 0.330,0.183 10 *a 0.94,1.375 1.623,0.564 1.623,0.564 1.717,0.564 false 0.816,1.369 1.333,0.277 1.333,0.277 1.425,0.277 false

Disconnect the F14 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F14-23 (MSCH) - F14-24 (MSCL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

7.CONNECT CONNECTOR
a.

Reconnect the F82 No. 2 junction connector connector.



NEXT

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 2 JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 2 JUNCTION CONNECTOR)
a.
U150157E03
2.302,0.208 2.219,0.208 2.219,0.208 1.823,1.25 true 2.615,0.531 2.531,0.531 2.531,0.531 1.896,1.26 true 0.188,0.094 0.385,0.323 0.198,0.229 10 false *a 2.688,0.458 3.115,0.625 0.427,0.167 10 false CANP 0.521,1.135 0.833,1.302 0.313,0.167 10 false F10 2.385,0.125 2.813,0.292 0.427,0.167 10 false CANN

Disconnect the F10 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F10-9 (CANP) - F10-10 (CANN) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - NO. 2 JUNCTION CONNECTOR)

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - FRONT POWER SEAT SWITCH LH)
a.
U180989E02
2.083,1.156 2.521,0.438 2.521,0.438 2.604,0.438 true 2.063,1.365 2.5,1.927 2.5,1.927 2.583,1.927 true 2.219,2.958 2.427,3.125 2.427,3.125 2.51,3.125 true 1.635,2.51 1.208,2.156 1.208,2.156 1.125,2.156 true 2.708,0.365 3.146,0.542 0.438,0.177 10 false CANP 2.667,1.854 3.104,2.031 0.438,0.177 10 false CANN 0.51,1.115 0.833,1.292 0.323,0.177 10 false F82 0.479,2.667 0.802,2.844 0.323,0.177 10 false F13 0.125,2.271 0.333,2.448 0.208,0.177 10 false *b 2.552,3.052 2.99,3.229 0.438,0.177 10 false BAT 0.135,0.094 0.344,0.271 0.208,0.177 10 false *a 0.844,2.094 1.073,2.271 0.229,0.177 10 false CG

Disconnect the F82 No. 2 junction connector connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F82-3 (CANP) - F82-14 (CANN) Ignition switch off 200 Ω or higher
F82-3 (CANP) - F13-4 (CG) Ignition switch off 200 Ω or higher
F82-14 (CANN) - F13-4 (CG) Ignition switch off 200 Ω or higher
F82-3 (CANP) - F13-16 (BAT) Ignition switch off 6 kΩ or higher
F82-14 (CANN) - F13-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

12.CONNECT CONNECTOR
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U180990E02
2.177,1.156 2.521,0.438 2.521,0.438 2.604,0.438 true 2.177,1.385 2.521,1.948 2.521,1.948 2.604,1.948 true 2.229,2.958 2.438,3.125 2.438,3.125 2.521,3.125 true 1.625,2.51 1.198,2.156 1.198,2.156 1.115,2.156 true 2.698,0.365 3.135,0.542 0.438,0.177 10 false MSCH 2.667,1.875 3.104,2.052 0.438,0.177 10 false MSCL 0.521,1.115 0.844,1.292 0.323,0.177 10 false F82 0.479,2.656 0.802,2.833 0.323,0.177 10 false F13 0.125,2.271 0.333,2.448 0.208,0.177 10 false *b 2.583,3.042 2.917,3.24 0.333,0.198 10 false BAT 0.125,0.104 0.333,0.281 0.208,0.177 10 false *a 0.823,2.094 1.052,2.271 0.229,0.177 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F82-2 (MSCH) - F82-13 (MSCL) Ignition switch off 108 to 132 Ω
F82-2 (MSCH) - F13-4 (CG) Ignition switch off 200 Ω or higher
F82-13 (MSCL) - F13-4 (CG) Ignition switch off 200 Ω or higher
F82-2 (MSCH) - F13-16 (BAT) Ignition switch off 6 kΩ or higher
F82-13 (MSCL) - F13-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

14.CONNECT CONNECTOR
11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.
U180991E02
2.313,1.135 2.531,0.417 2.531,0.417 2.615,0.417 true 2.323,1.354 2.542,1.917 2.542,1.917 2.625,1.917 true 2.229,2.927 2.438,3.094 2.438,3.094 2.521,3.094 true 1.635,2.51 1.208,2.156 1.208,2.156 1.125,2.156 true 2.667,0.354 3.104,0.531 0.438,0.177 10 false CANP 2.708,1.875 3.146,2.052 0.438,0.177 10 false CANN 0.5,1.115 0.823,1.292 0.323,0.177 10 false F82 0.49,2.646 0.813,2.823 0.323,0.177 10 false F13 0.125,2.271 0.333,2.448 0.208,0.177 10 false *b 2.604,3.031 2.969,3.198 0.365,0.167 10 false BAT 0.125,0.104 0.333,0.281 0.208,0.177 10 false *a 0.833,2.104 1.063,2.281 0.229,0.177 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F82-1 (CANP) - F82-12 (CANN) Ignition switch off 108 to 132 Ω
F82-1 (CANP) - F13-4 (CG) Ignition switch off 200 Ω or higher
F82-12 (CANN) - F13-4 (CG) Ignition switch off 200 Ω or higher
F82-1 (CANP) - F13-16 (BAT) Ignition switch off 6 kΩ or higher
F82-12 (CANN) - F13-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR

NG

16.CONNECT CONNECTOR
12.CONNECT CONNECTOR
a.

Reconnect the F82 No. 2 junction connector connector.



NEXT

13.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH LH)
13.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT SWITCH LH)
a.
U150335E03
2.292,1.5 2.75,1.083 2.75,1.083 2.833,1.083 true 2.198,1.51 2.635,1.896 2.635,1.896 2.719,1.896 true 2.354,3.042 2.563,3.208 2.563,3.208 2.646,3.208 true 1.729,2.583 1.302,2.229 1.302,2.229 1.219,2.229 true 2.896,1.042 3.333,1.219 0.438,0.177 10 false CANN 2.792,1.844 3.229,2.021 0.438,0.177 10 false CANP 1.219,1.271 1.542,1.448 0.323,0.177 10 false b19 0.385,2.729 0.708,2.906 0.323,0.177 10 false F13 0.104,2.167 0.313,2.344 0.208,0.177 10 false *b 2.719,3.135 3.156,3.313 0.438,0.177 10 false BAT 0.115,0.094 0.323,0.271 0.208,0.177 10 false *a 0.927,2.125 1.156,2.302 0.229,0.177 10 false CG

Disconnect the b19 front power seat switch LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
b19-8 (CANP) - b19-7 (CANN) Ignition switch off 54 to 69 Ω
b19-8 (CANP) - F13-4 (CG) Ignition switch off 200 Ω or higher
b19-7 (CANN) - F13-4 (CG) Ignition switch off 200 Ω or higher
b19-8 (CANP) - F13-16 (BAT) Ignition switch off 6 kΩ or higher
b19-7 (CANN) - F13-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Switch LH)
*b Front view of DLC3



OK

REPLACE FRONT POWER SEAT SWITCH LH

NG

REPAIR OR REPLACE FRONT POWER SEAT SWITCH LH CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

14.CONNECT CONNECTOR
a.

Reconnect the F82 No. 2 junction connector connector.



NEXT

15.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
15.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U150386E03
1.667,2.49 1.51,2.188 1.51,2.188 1.427,2.188 true 2.229,2.917 2.438,3.083 2.438,3.083 2.521,3.083 true 0.813,1.302 0.958,1.771 0.958,1.771 1.073,1.771 true 0.917,1.24 0.781,0.594 0.781,0.594 0.646,0.594 true 1.135,1.708 1.625,1.885 0.49,0.177 10 false MSCH 0.135,0.521 0.615,0.698 0.479,0.177 10 false MSCL 0.49,2.688 0.813,2.865 0.323,0.177 10 false F13 0.063,0.021 0.271,0.198 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.104 1.375,2.281 0.24,0.177 10 false CG 2.615,2.99 3.052,3.167 0.438,0.177 10 false BAT 1.615,0.229 1.885,0.406 0.271,0.177 10 false F14

Disconnect the F14 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F14-23 (MSCH) - F14-24 (MSCL) Ignition switch off 108 to 132 Ω
F14-23 (MSCH) - F13-4 (CG) Ignition switch off 200 Ω or higher
F14-24 (MSCL) - F13-4 (CG) Ignition switch off 200 Ω or higher
F14-23 (MSCH) - F13-16 (BAT) Ignition switch off 6 kΩ or higher
F14-24 (MSCL) - F13-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE COMBINATION METER ASSEMBLY CAN MAIN WIRE OR CONNECTOR (MSCH, MSCL)

16.CONNECT CONNECTOR
a.

Reconnect the F82 No. 2 junction connector connector.



NEXT

17.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
17.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.
U150385E03
1.625,2.521 1.51,2.188 1.51,2.188 1.427,2.188 true 2.229,2.958 2.438,3.125 2.438,3.125 2.521,3.125 true 1.833,0.958 2.354,0.208 2.354,0.208 2.479,0.208 true 1.771,1.01 2.354,1.74 2.354,1.74 2.469,1.74 true 2.531,0.135 3.021,0.313 0.49,0.177 10 false CANP 2.531,1.667 3.01,1.844 0.479,0.177 10 false CANN 0.479,2.698 0.802,2.875 0.323,0.177 10 false F13 0.073,0.104 0.281,0.281 0.208,0.177 10 false *a 0.063,2 0.271,2.177 0.208,0.177 10 false *b 1.135,2.104 1.375,2.281 0.24,0.177 10 false CG 2.583,3.052 3.021,3.229 0.438,0.177 10 false BAT 0.458,0.854 0.781,1.031 0.323,0.177 10 false F10

Disconnect the F10 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F10-9 (CANP) - F10-10 (CANN) Ignition switch off 108 to 132 Ω
F10-9 (CANP) - F13-4 (CG) Ignition switch off 200 Ω or higher
F10-10 (CANN) - F13-4 (CG) Ignition switch off 200 Ω or higher
F10-9 (CANP) - F13-16 (BAT) Ignition switch off 6 kΩ or higher
F10-10 (CANN) - F13-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) MAIN WIRE OR CONNECTOR (CANP, CANN)

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - BATTERY AND GROUND)
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


U150159E03
5.896,0.5 5.958,0.5 5.958,0.5 6.156,1.156 true 3.813,0.5 3.875,0.5 3.875,0.5 4.083,1.156 true 6.458,0.5 6.396,0.5 6.396,0.5 6.271,1.167 true 6.708,0.823 6.635,0.823 6.635,0.823 6.396,1.156 true 0.604,0.521 0.667,0.521 0.667,0.521 0.854,0.906 true 6.26,1.542 6.333,1.542 6.333,1.542 6.521,1.219 true 3.354,0.438 3.771,0.604 0.417,0.167 10 false GND1 5.531,0.438 5.844,0.604 0.313,0.167 10 false ACC 6.521,0.438 6.958,0.604 0.438,0.167 10 false BECU 6.771,0.76 7.156,0.927 0.385,0.167 10 false ALTB 2.385,0.052 2.583,0.281 0.198,0.229 10 false *b 0.094,0.031 0.292,0.26 0.198,0.229 10 false *a 0.177,0.458 0.604,0.625 0.427,0.167 10 false GND2 0.177,0.927 0.49,1.094 0.313,0.167 10 false F10 2.406,1.083 2.542,1.25 0.135,0.167 10 false A 6.031,1.49 6.208,1.656 0.177,0.167 10 false IG

Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
*b Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F10-3 (GND2) - Body ground Always Below 1 Ω
A-11 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-30 (BECU) - Body ground Always 11 to 14 V
A-31 (ALTB) - Body ground Always 11 to 14 V
A-29 (ACC) - Body ground Ignition switch ACC 11 to 14 V
A-32 (IG) - Body ground Ignition switch ON 11 to 14 V




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR