Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › from 2013.08
RM1440E _58 Vehicle Interior _056155 DOOR LOCK _0274054 POWER DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U149717E06
1.604,1.531 1.844,1.281 1.844,1.281 1.927,1.281 true 1.604,1.854 1.844,1.615 1.844,1.615 1.927,1.615 true 1.615,2.208 1.854,1.969 1.854,1.969 1.938,1.969 true 0.906,1.583 1.094,1.75 0.188,0.167 10 false 2F 1.083,3.875 1.365,4.031 0.281,0.156 10 false F10 0.906,2.167 1.094,2.323 0.188,0.156 10 false 2D 5.854,1.542 6.063,1.698 0.208,0.156 10 false 2B 5.844,2.188 6.052,2.344 0.208,0.156 10 false 2C 1.063,2.76 1.271,2.917 0.208,0.156 10 false 2E 3.75,1.365 3.865,1.51 0.115,0.146 10 false A 1.99,1.219 2.26,1.365 0.271,0.146 10 false F8 1.969,1.563 2.24,1.708 0.271,0.146 10 false F9 1.979,1.896 2.25,2.042 0.271,0.146 10 false F10 3.625,3.865 3.823,4.021 0.198,0.156 10 false F9 1.135,5.177 1.354,5.333 0.219,0.156 10 false 2F 1.865,6.406 2.083,6.563 0.219,0.156 10 false 2B 4.938,6.417 5.156,6.573 0.219,0.156 10 false 2C 3.49,7.677 3.625,7.833 0.135,0.156 10 false A 3.938,5.188 4.135,5.344 0.198,0.156 10 false 2D 5.875,5.177 6.073,5.333 0.198,0.156 10 false 2E 5.927,3.865 6.125,4.021 0.198,0.156 10 false F8

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
F10-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU (multiplex network body ECU).


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2F-27 (FLCY) - Body ground R - Body ground Front door LH courtesy light switch input Front door LH open Below 1 V
2F-27 (FLCY) - Body ground R - Body ground Front door LH courtesy light switch input Front door LH closed 11 to 14 V
2B-15 (FRCY) - Body ground B - Body ground Front door RH courtesy light switch input Front door RH open Below 1 V
2B-15 (FRCY) - Body ground B - Body ground Front door RH courtesy light switch input Front door RH closed 11 to 14 V
F8-3 (LCTY) - Body ground V - Body ground Rear door LH courtesy light switch input Rear door LH open Below 1 V
F8-3 (LCTY) - Body ground V - Body ground Rear door LH courtesy light switch input Rear door LH closed 11 to 14 V
F10-27 (RCTY) - Body ground R - Body ground Rear door RH courtesy light switch input Rear door RH open Below 1 V
F10-27 (RCTY) - Body ground R - Body ground Rear door RH courtesy light switch input Rear door RH closed 11 to 14 V
F9-9 (L1) - Body ground B - Body ground Door control switch lock input Door control switch on Below 1 V
F9-9 (L1) - Body ground B - Body ground Door control switch lock input Door control switch off Pulse generation (See waveform 1 or 2)
F9-10 (UL1) - Body ground W - Body ground Door control switch unlock input Door control switch on Below 1 V
F9-10 (UL1) - Body ground W - Body ground Door control switch unlock input Door control switch off Pulse generation (See waveform 3 or 4)
F9-11 (L2) - Body ground LG - Body ground Driver side door key-linked lock input Driver side door key cylinder in lock position Below 1 V
F9-11 (L2) - Body ground LG - Body ground Driver side door key-linked lock input Ignition switch off, all doors closed and driver side door key cylinder in neutral position Pulse generation (See waveform 5 or 6)
F9-24 (UL3) - Body ground GR - Body ground Driver side door key-linked unlock input Driver side door key cylinder in unlock position Below 1 V
F9-24 (UL3) - Body ground GR - Body ground Driver side door key-linked unlock input Ignition switch off, all doors closed and driver side door key cylinder in neutral position Pulse generation (See waveform 7 or 8)
2B-3 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (except rear LH and back door) Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position Below 1 V
2B-3 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (except rear LH and back door) Lock side of driver or passenger side door control switch pushed, or driver side door key cylinder in lock position 11 to 14 V
2F-8 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (for rear LH) Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position Below 1 V
2F-8 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (for rear LH) Lock side of driver or passenger side door control switch pushed, or driver side door key cylinder in lock position 11 to 14 V
2B-1 (ACTD) - Body ground W - Body ground Driver side door lock motor unlock drive output Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position Below 1 V
2B-1 (ACTD) - Body ground W - Body ground Driver side door lock motor unlock drive output Unlock side of driver or passenger side door control switch pushed, or driver side door key cylinder in unlock position 11 to 14 V
2B-2 (ACT-) - Body ground W - Body ground Door lock motor unlock drive output (for front RH and rear RH) Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position Below 1 V
2B-2 (ACT-) - Body ground W - Body ground Door lock motor unlock drive output (for front RH and rear RH) Unlock side of driver or passenger side door control switch pushed, or driver side door key cylinder in unlock position 11 to 14 V
2F-10 (ACT-) - Body ground W - Body ground Door lock motor unlock drive output (for rear LH) Driver or passenger side door control switch not pushed and driver side door key cylinder in neutral position Below 1 V
2F-10 (ACT-) - Body ground W - Body ground Door lock motor unlock drive output (for rear LH) Unlock side of driver or passenger side door control switch pushed, or driver side door key cylinder in unlock position 11 to 14 V
2F-9 (TR+) - Body ground R - Body ground Back door unlock motor output Back door opener switch pushed Below 1 V
2F-9 (TR+) - Body ground R - Body ground Back door unlock motor output Back door opener switch free 11 to 14 V
F9-7 (LSFL) - Body ground G - Body ground Front door LH lock position switch input Front door LH unlocked Below 1 V
F9-7 (LSFL) - Body ground G - Body ground Front door LH lock position switch input Ignition switch off, all doors closed and front door LH locked Pulse generation (See waveform 9 or 10)
F9-18 (LSFR) - Body ground G - Body ground Front door RH lock position switch input Front door RH unlocked Below 1 V
F9-18 (LSFR) - Body ground G - Body ground Front door RH lock position switch input Ignition switch off, all doors closed and front door RH locked Pulse generation (See waveform 11 or 12)
2F-25 (LSWL) - Body ground V - Body ground Rear door LH lock position switch input Rear door LH unlocked Below 1 V
2F-25 (LSWL) - Body ground V - Body ground Rear door LH lock position switch input Ignition switch off, all doors closed and rear door LH locked Pulse generation (See waveform 13 or 14)
F10-2 (LSWR) - Body ground V - Body ground Rear door RH lock position switch input Rear door RH unlocked Below 1 V
F10-2 (LSWR) - Body ground V - Body ground Rear door RH lock position switch input Ignition switch off, all doors closed and rear door RH locked Pulse generation (See waveform 15 or 16)

If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.


e.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 1

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) F9-9 (L1) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Door control switch off


f.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) F9-9 (L1) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Door control switch off


g.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) F9-10 (UL1) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Door control switch off


h.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) F9-10 (UL1) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Door control switch off


i.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 5.

Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) F9-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door key cylinder in neutral position


j.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 6.

Waveform 6 (Reference)
Item Content
Terminal No. (Symbol) F9-11 (L2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door key cylinder in neutral position


k.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 7.

Waveform 7 (Reference)
Item Content
Terminal No. (Symbol) F9-24 (UL3) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and driver side door key cylinder in neutral position


l.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 8.

Waveform 8 (Reference)
Item Content
Terminal No. (Symbol) F9-24 (UL3) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and driver side door key cylinder in neutral position


m.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 9.

Waveform 9 (Reference)
Item Content
Terminal No. (Symbol) F9-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door LH locked


n.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 10.

Waveform 10 (Reference)
Item Content
Terminal No. (Symbol) F9-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door LH locked


o.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 11.

Waveform 11 (Reference)
Item Content
Terminal No. (Symbol) F9-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door RH locked


p.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 12.

Waveform 12 (Reference)
Item Content
Terminal No. (Symbol) F9-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door RH locked


q.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 13.

Waveform 13 (Reference)
Item Content
Terminal No. (Symbol) 2F-25 (LSWL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door LH locked


r.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 14.

Waveform 14 (Reference)
Item Content
Terminal No. (Symbol) 2F-25 (LSWL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door LH locked


s.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 15.

Waveform 15 (Reference)
Item Content
Terminal No. (Symbol) F10-2 (LSWR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door RH locked


t.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 16.

Waveform 16 (Reference)
Item Content
Terminal No. (Symbol) F10-2 (LSWR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door RH locked



CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


U149777E05
4.115,0.406 4.417,0.563 0.302,0.156 10 false W10 2.833,0.396 3.031,0.552 0.198,0.156 10 false V2

a.

Disconnect the V2 and W10 multiplex network door ECU (back door P/W) connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-1 (BDR) - Body ground B - Body ground Battery power supply Always 11 to 14 V
V2-7 (BECU) - Body ground L - Body ground Battery power supply Always 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the V2 and W10 multiplex network door ECU (back door P/W) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W10-10 (BDCY) - W10-18 (CTYE) P - G Back door courtesy switch input Back door closed Pulse generation (See waveform 1 or 2)
W10-10 (BDCY) - W10-18 (CTYE) P - G Back door courtesy switch input Back door open Below 1 V
W10-16 (BKL) - W10-8 (KEYE) P - V Tail gate control switch lock input Back door lock key cylinder in neutral position Pulse generation (See waveform 3 or 4)
W10-16 (BKL) - W10-8 (KEYE) P - V Tail gate control switch lock input Back door lock key cylinder in lock position Below 1 V
W10-15 (BKUL) - W10-8 (KEYE) R - V Tail gate control switch unlock input Back door lock key cylinder in neutral position Pulse generation (See waveform 3 or 4)
W10-15 (BKUL) - W10-8 (KEYE) R - V Tail gate control switch unlock input Back door lock key cylinder in unlock position Below 1 V
W10-24 (HSW+) - W10-7 (HSW-) GR - LG Back door opener switch input Back door opener switch off Pulse generation (See waveform 5 or 6)
W10-24 (HSW+) - W10-7 (HSW-) GR - LG Back door opener switch input Back door opener switch on Below 1 V

If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.


e.
B242623E02
0.103,0.985 0.440,1.141 0.336,0.156 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) W10-10 (BDCY) - W10-18 (CTYE)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door closed


f.
B242624E01
0.095,0.987 0.441,1.138 0.346,0.151 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) W10-10 (BDCY) - W10-18 (CTYE)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door closed


g.
B242623E02
0.103,0.985 0.440,1.141 0.336,0.156 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol)

W10-16 (BKL) - W10-8 (KEYE)

W10-15 (BKUL) - W10-8 (KEYE)


Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door lock key cylinder in neutral position


h.
B242624E01
0.095,0.987 0.441,1.138 0.346,0.151 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol)

W10-16 (BKL) - W10-8 (KEYE)

W10-15 (BKUL) - W10-8 (KEYE)


Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door lock key cylinder in neutral position


i.
B242623E02
0.103,0.985 0.440,1.141 0.336,0.156 10 GND

Using an oscilloscope, check waveform 5.

Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) W10-24 (HSW+) - W10-7 (HSW-)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door opener switch off


j.
B242624E01
0.095,0.987 0.441,1.138 0.346,0.151 10 GND

Using an oscilloscope, check waveform 6.

Waveform 6 (Reference)
Item Content
Terminal No. (Symbol) W10-24 (HSW+) - W10-7 (HSW-)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door opener switch off



CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>TERMINALS OF ECU)