Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056155 DOOR LOCK _0274064 WIRELESS DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U149717E06
1.604,1.531 1.844,1.281 1.844,1.281 1.927,1.281 true 1.604,1.854 1.844,1.615 1.844,1.615 1.927,1.615 true 1.615,2.208 1.854,1.969 1.854,1.969 1.938,1.969 true 0.906,1.583 1.094,1.75 0.188,0.167 10 false 2F 1.083,3.875 1.365,4.031 0.281,0.156 10 false F10 0.906,2.167 1.094,2.323 0.188,0.156 10 false 2D 5.854,1.542 6.063,1.698 0.208,0.156 10 false 2B 5.844,2.188 6.052,2.344 0.208,0.156 10 false 2C 1.063,2.76 1.271,2.917 0.208,0.156 10 false 2E 3.75,1.365 3.865,1.51 0.115,0.146 10 false A 1.99,1.219 2.26,1.365 0.271,0.146 10 false F8 1.969,1.563 2.24,1.708 0.271,0.146 10 false F9 1.979,1.896 2.25,2.042 0.271,0.146 10 false F10 3.625,3.865 3.823,4.021 0.198,0.156 10 false F9 1.135,5.177 1.354,5.333 0.219,0.156 10 false 2F 1.865,6.406 2.083,6.563 0.219,0.156 10 false 2B 4.938,6.417 5.156,6.573 0.219,0.156 10 false 2C 3.49,7.677 3.625,7.833 0.135,0.156 10 false A 3.938,5.188 4.135,5.344 0.198,0.156 10 false 2D 5.875,5.177 6.073,5.333 0.198,0.156 10 false 2E 5.927,3.865 6.125,4.021 0.198,0.156 10 false F8

a.

b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Auxiliary battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Auxiliary battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
F10-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.



d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
2F-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH open Below 1 V
2F-27 (FLCY) - Body ground R - Body ground Front door LH courtesy switch input Front door LH closed 11 to 14 V
2B-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH open Below 1 V
2B-15 (FRCY) - Body ground B - Body ground Front door RH courtesy switch input Front door RH closed 11 to 14 V
F8-3 (LCTY) - Body ground V - Body ground Rear door LH courtesy light switch input Rear door LH open Below 1 V
F8-3 (LCTY) - Body ground V - Body ground Rear door LH courtesy light switch input Rear door LH closed 11 to 14 V
F9-6 (RCTY) - Body ground R - Body ground Rear door RH courtesy light switch input Rear door RH open Below 1 V
F9-6 (RCTY) - Body ground R - Body ground Rear door RH courtesy light switch input Rear door RH closed 11 to 14 V
F9-7 (LSFL) - Body ground G - Body ground Front door LH lock position switch input Front door LH unlocked Below 1 V
F9-7 (LSFL) - Body ground G - Body ground Front door LH lock position switch input Ignition switch off, all doors closed and front door LH locked Pulse generation (see waveform 1 or 2)
F9-18 (LSFR) - Body ground G - Body ground Front door RH lock position switch input Front door RH unlocked Below 1 V
F9-18 (LSFR) - Body ground G - Body ground Front door RH lock position switch input Ignition switch off, all doors closed and front door RH locked Pulse generation (see waveform 3 or 4)
2F-25 (LSWL) - Body ground V - Body ground Rear door LH lock position switch input Rear door LH unlocked Below 1 V
2F-25 (LSWL) - Body ground V - Body ground Rear door LH lock position switch input Ignition switch off, all doors closed and rear door LH locked Pulse generation (see waveform 5 or 6)
F10-2 (LSWR) - Body ground V - Body ground Rear door RH lock position switch input Rear door RH unlocked Below 1 V
F10-2 (LSWR) - Body ground V - Body ground Rear door RH lock position switch input Ignition switch off, all doors closed and rear door RH locked Pulse generation (see waveform 7 or 8)
F9-25 (PRG) - Body ground LG - Body ground Door control receiver output Key in ignition key cylinder → No key in ignition key cylinder Pulse generation
F9-26 (RDA) - Body ground P - Body ground Door control receiver input No key in ignition key cylinder, all doors closed and transmitter switch off → on Pulse generation
2D-13 (BZR) - Body ground GR - Body ground Wireless door lock buzzer signal Wireless door lock buzzer off Below 1 V
2D-13 (BZR) - Body ground GR - Body ground Wireless door lock buzzer signal Wireless door lock buzzer on 11 to 14 V
F9-3 (HAZ) - Body ground W - Body ground Hazard warning signal light signal output Hazard warning signal switch off Below 1 V
F9-3 (HAZ) - Body ground W - Body ground Hazard warning signal light signal output Hazard warning signal switch on 11 to 14 V
F9-17 (KSW) - Body ground B - Body ground Unlock warning switch input No key in ignition key cylinder 10 kΩ or higher
F9-17 (KSW) - Body ground B - Body ground Unlock warning switch input Key in ignition key cylinder Below 1 Ω

If the result is not as specified, the main body ECU or driver side junction block assembly may have a malfunction.


e.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) F9-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door LH locked


f.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) F9-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door LH locked


g.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) F9-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door RH locked


h.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) F9-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and front door RH locked


i.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 5.

Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) 2F-25 (LSWL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door LH locked


j.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 6.

Waveform 6 (Reference)
Item Content
Terminal No. (Symbol) 2F-25 (LSWL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door LH locked


k.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 7.

Waveform 7 (Reference)
Item Content
Terminal No. (Symbol) F10-2 (LSWR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door RH locked


l.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 8.

Waveform 8 (Reference)
Item Content
Terminal No. (Symbol) F10-2 (LSWR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and rear door RH locked



CHECK MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)


U149777E05
4.115,0.406 4.417,0.563 0.302,0.156 10 false W10 2.833,0.396 3.031,0.552 0.198,0.156 10 false V2

a.

Disconnect the V2 multiplex network door ECU (back door P/W) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V2-1 (BDR) - Body ground B - Body ground Battery power supply Always 11 to 14 V
V2-7 (BECU) - Body ground L - Body ground Battery power supply Always 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
V2-8 (SIG) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
V2-6 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the V2 multiplex network door ECU (back door P/W) connector.


d.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
W10-10 (BDCY) - W10-18 (CTYE) P - G Back door courtesy switch input Back door closed Pulse generation (see waveform 1 or 2)
W10-10 (BDCY) - W10-18 (CTYE) P - G Back door courtesy switch input Back door open Below 1 V

If the result is not as specified, the multiplex network door ECU (back door P/W) may have a malfunction.


e.
B245381E01
0.178,0.926 0.517,1.093 0.339,0.166 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) W10-10 (BDCY) - W10-18 (CTYE)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door closed


f.
B245382E01
0.179,0.927 0.518,1.094 0.339,0.166 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) W10-10 (BDCY) - W10-18 (CTYE)
Tool Setting 5 V/DIV., 10 ms/DIV.
Condition Back door closed