Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM1440E _58 Vehicle Interior _056155 DOOR LOCK _0274064 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. The main body ECU then controls all the doors by sending lock/unlock signals to each door.

WIRING DIAGRAM

B242194E01
0.699,2.952 2.132,3.128 1.434,0.177 10 Door Control Receiver 0.699,2.767 1.019,2.943 0.320,0.177 10 O11 2.055,0.712 2.376,0.889 0.320,0.177 10 3 1.601,0.805 1.957,0.982 0.356,0.177 10 PRG 2.055,1.212 2.376,1.388 0.320,0.177 10 2 5.012,2.178 5.332,2.355 0.320,0.177 10 F9 1.605,1.305 1.945,1.481 0.341,0.177 10 RDA 2.055,1.704 2.376,1.880 0.320,0.177 10 5 1.73,1.796 1.946,1.973 0.217,0.177 10 +B 2.055,2.15 2.376,2.326 0.320,0.177 10 1 1.611,2.243 1.945,2.419 0.334,0.177 10 GND 5.22,0.805 5.637,0.982 0.417,0.177 10 PRG 5.22,1.293 5.622,1.470 0.402,0.177 10 RDA 4.967,0.709 5.385,0.885 0.417,0.177 10 25 4.967,1.211 5.385,1.387 0.417,0.177 10 26 5.012,2.362 6.725,2.709 1.713,0.347 10 Main Body ECU (Multiplex Network Body ECU) 3.179,2.281 4.052,2.461 0.872,0.181 10 from Battery 2.464,1.922 2.941,2.103 0.477,0.181 10 ECU-B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the door control receiver, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>REGISTRATION).



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Each door locks and unlocks normally.




OK

2.CHECK KEY REMINDER WARNING OPERATION

NG

2.CHECK KEY REMINDER WARNING OPERATION
a.

Check the key reminder buzzer operation (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK).

HINT:

If the key reminder buzzer is functioning normally, it can be assumed that the unlock warning switch is also functioning normally.


OK:

Key reminder buzzer operates normally.




OK

3.CHECK WIRELESS DOOR CONTROL TRANSMITTER

NG

3.CHECK WIRELESS DOOR CONTROL TRANSMITTER
a.

Check whether the wireless door lock control functions operate normally with another registered transmitter.

OK:

Wireless door lock control functions operate normally.




OK

4.CHECK TRANSMITTER BATTERY

NG

5.CHECK FOR ELECTRICAL NOISE
4.CHECK TRANSMITTER BATTERY
a.

Remove the battery from the inoperative wireless door control transmitter (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Battery positive (+) - Battery negative (-) Always 2.5 to 3.2 V




OK

REPLACE DOOR CONTROL TRANSMITTER

NG

REPLACE TRANSMITTER BATTERY

5.CHECK FOR ELECTRICAL NOISE
a.

Move the transmitter in the vicinity of the door control receiver.

HINT:

Refer to Parts Location for the location of the door control receiver (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>PARTS LOCATION).



b.

Press and hold either the lock or unlock transmitter switch for 1 second, and check that the doors are locked or unlocked accordingly.

OK:

Wireless door lock control functions operate normally.


HINT:
·

Check if electrical noise is the cause by moving the door control transmitter closer to the door control receiver. Moving closer will decrease the effects of electrical noise.

·

If the operation check can be performed normally, there is a high probability that electrical noise or a decrease in output from the door control transmitter is the cause of the malfunction. There is a high probability that electrical noise is the cause if the problem occurs only in a certain location or only during a certain time of day. Also, custom components may be causing electrical noise. If custom components are installed in the vehicle, remove them and perform the operation check again.





OK

FIND CAUSE OF ELECTRICAL NOISE AND REMOVE IT

NG

6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU)
6.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU)
a.

Disconnect the O11 receiver connector.


b.

Disconnect the F9 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-2 (RDA) - F9-26 (RDA) Always Below 1 Ω
O11-3 (PRG) - F9-25 (PRG)
O11-2 (RDA) or F9-26 (RDA) - Body ground Always 10 kΩ or higher
O11-3 (PRG) or F9-25 (PRG) - Body ground




OK

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
U149701E03
1.229,1.417 0.979,1.813 true 2.188,1.417 2.344,1.823 true 0.719,1.844 1.073,2.031 0.354,0.188 10 false GND 2.313,1.844 2.531,2.031 0.219,0.188 10 false +B 0.146,0.063 0.344,0.25 0.198,0.188 10 false *a 0.469,1.104 0.823,1.292 0.354,0.188 10 false O11

Disconnect the O11 receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O11-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
O11-5 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)



OK

8.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.

Using an oscilloscope, check the waveform.

E353058E01
0.792,1.635 1.125,1.854 0.333,0.219 2.271,2.427 1.844,2.073 true 0.531,0.073 2.771,0.438 2.24,0.365 10 false Component with harness connected: (Door Control Receiver) 3.635,0.104 5.188,0.292 1.552,0.188 10 false RDA Output (Reference): 2.333,2.344 2.688,2.521 0.354,0.177 10 false RDA 0.823,1.667 1.104,1.844 0.281,0.177 10 false O11 4.906,1.042 6.365,1.219 1.458,0.177 10 false Transmitter Switch On 3.76,1.375 4.115,1.542 0.354,0.167 10 false 10 V 3.792,1.969 4.448,2.135 0.656,0.167 10 false Below 1 V 5.021,2.177 5.573,2.365 0.552,0.188 10 false 50 μsec.

Measurement Condition
Item Content
Tester Connection O11-2 (RDA) - Body ground
Tool Setting 10 V/DIV., 50 μs/DIV.
Condition No key in ignition key cylinder, all doors closed and transmitter switch off → on

OK:

Waveform is output normally (refer to illustration).




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE DOOR CONTROL RECEIVER