Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056156 THEFT DETERRENT / KEYLESS ENTRY _0274066 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Circuit  


DESCRIPTION

When the engine immobiliser system is set, the security indicator light blinks continuously, but does not illuminate if the engine immobiliser system is not set.


WIRING DIAGRAM

B242452E03
0.99,1.984 3.095,2.150 2.105,0.166 10 Telltale Light Assembly 1.252,1.137 2.715,1.300 1.463,0.163 10 Security Indicator Light 3.229,1.433 3.385,1.619 0.156,0.186 10 E 3.152,0.891 3.427,1.077 0.275,0.186 10 LP 3.427,1.383 3.789,1.569 0.362,0.186 10 1 3.426,0.841 3.732,1.027 0.306,0.186 10 2 4.721,0.857 4.840,1.042 0.119,0.186 10 8 4.615,2.055 4.889,2.241 0.275,0.186 10 F34 0.993,1.817 1.293,2.003 0.300,0.186 10 F32 4.935,0.97 5.259,1.156 0.324,0.186 10 IND 4.615,2.205 6.695,2.394 2.081,0.189 10 Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the transponder key ECU assembly, refer to the Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Check that the security indicator light illuminates when operating it with the Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DATA LIST / ACTIVE TEST).

Immobiliser
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF The test is possible when the following conditions are met:

The key is in the ignition key cylinder.



OK:

Security indicator light can be turned on and off using the intelligent tester.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT TELLTALE LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT)
2.INSPECT TELLTALE LIGHT ASSEMBLY (SECURITY INDICATOR LIGHT)
a.
B216769E06
2.375,1.188 2.594,1.552 false 2.063,1.188 1.844,1.552 false 2.583,1.563 2.708,1.771 0.125,0.208 10 false E 1.74,1.552 1.938,1.76 0.198,0.208 10 false LP

Remove the telltale light assembly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL).


b.

Apply battery voltage between the terminals of the telltale light assembly and check that the security indicator light illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (LP)
Battery negative (-) → 1 (E)
Security indicator light illuminates




OK

3.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT - TRANSPONDER KEY ECU AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (TELLTALE LIGHT - TRANSPONDER KEY ECU AND BODY GROUND)
a.

Disconnect the F32 light connector.


b.

Disconnect the F34 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-2 (LP) - F34-8 (IND) Always Below 1 Ω
F32-1 (E) - Body ground Always Below 1 Ω
F32-2 (LP) or F34-8 (IND) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR