Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM1440E _58 Vehicle Interior _056157 LIGHTING (INT) _0274081 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  ACC Signal Circuit  


DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU.

WIRING DIAGRAM

E199769E40
5.208,2.823 6.896,3.198 1.688,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 5.229,2.656 5.406,2.813 0.177,0.156 10 false A 5.313,0.948 5.521,1.115 0.208,0.167 10 false 29 5.604,1.052 5.958,1.219 0.354,0.167 10 false ACC 4.563,1.188 4.938,1.354 0.375,0.167 10 false ACC 3.521,1.823 3.865,1.99 0.344,0.167 10 false ACC 2.469,1.052 2.688,1.208 0.219,0.156 10 false 2E 2.521,0.875 2.656,1.042 0.135,0.167 10 false 1 2.479,2.083 2.698,2.24 0.219,0.156 10 false 2B 2.521,1.885 2.656,2.052 0.135,0.167 10 false 4 2.469,1.531 2.688,1.688 0.219,0.156 10 false 2C 2.479,1.354 2.677,1.521 0.198,0.167 10 false 48 2.823,2.448 5.156,2.625 2.333,0.177 10 false Driver Side Junction Block Assembly 0.698,1.531 1.969,1.729 1.271,0.198 10 false from Ignition Switch 1.146,1.063 1.969,1.26 0.823,0.198 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IGNITION SWITCH)
a.

Using the intelligent tester, read the Data List (See page Vehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC SW Ignition switch ACC signal / ON or OFF ON: Ignition switch ACC
OFF: Ignition switch off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU)
2.CHECK HARNESS AND CONNECTOR (BATTERY - MAIN BODY ECU)
a.
U150528E01
0.162,0.098 0.366,0.275 0.205,0.177 10 *a 1.666,0.53 1.811,0.686 0.145,0.156 10 A 2.324,1.389 2.667,1.558 0.343,0.170 10 ACC 2.886,1.109 2.789,1.47 2.789,1.47 2.72,1.47 false

Remove the main body ECU (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A-29 (ACC) - Body ground Ignition switch ACC 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR