Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Tachometer Malfunction  


DESCRIPTION

In this circuit, the meter CPU receives engine speed signals from the ECM using the CAN communication system. The meter CPU displays the engine speed, which is calculated based on the data received from the ECM.

WIRING DIAGRAM

E200122E02
1.549,2.64 1.887,2.811 0.338,0.171 10 ECM 4.535,2.628 6.374,2.798 1.839,0.171 10 Combination Meter Assembly 0.798,3.325 2.516,3.518 1.717,0.193 10 : CAN Communication Line

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication DTC is not output A
CAN communication DTC is output B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TACHO METER OPERATION)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TACHO METER OPERATION)
a.

Use the Active Test to check the operation of the tachometer (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Tacho Meter Operation Tachometer 0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 (rpm) Confirm that the vehicle is stopped with the engine idling.

OK:

Tachometer indication is normal.




OK

3.READ VALUE USING INTELLIGENT TESTER (ENGINE RPM)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (ENGINE RPM)
a.

Use the Data List to check the engine speed (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Rpm Engine speed/Min.: 0 rpm, Max.: 12800 rpm 600 to 700 rpm (When idling) If the data received from the ECM exceeds the range that can be displayed on the meter, the meter continues to display the maximum value.

OK:

Engine speed displayed on the intelligent tester is almost the same as the tachometer indication.



b.

Record the engine speed displayed on the intelligent tester.

HINT:

Check the engine speed when the engine is fully warmed up, and the air conditioning and all electrical accessories are off.




OK

4.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

NG

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Use the Data List to check the engine speed (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Speed Engine speed/Min.: 0 rpm, Max.: 16383 rpm 600 to 700 rpm (When idling) -

OK:

Engine speed displayed on the intelligent tester is almost the same as the previously recorded intelligent tester value (Body Electrical / Combination Meter / Data List / Engine Rpm).




OK

5.REPLACE ECM

NG

5.REPLACE ECM
a.

Replace the ECM with a new or normally functioning one (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>ECM>REMOVAL).

OK:

The operation of the tachometer returns to normal.




OK

END

NG

REPLACE COMBINATION METER ASSEMBLY