Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter receives vehicle speed signals from the skid control ECU via the CAN communication line. The wheel speed sensors output voltages that vary according to the vehicle speed. The skid control ECU supplies power to the wheel speed sensors. The skid control ECU calculates the vehicle speed based on the pulses of the voltage.

WIRING DIAGRAM

E200122E01
0.992,2.644 2.592,2.970 1.599,0.326 10 Master Cylinder Solenoid (Skid Control ECU) 0.816,3.346 2.633,3.524 1.817,0.178 10 : CAN Communication Line 4.542,2.644 6.391,2.816 1.849,0.172 10 Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).


HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication DTC is not output A
CAN communication DTC is output B



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)
a.

Use the Active Test to check the operation of the speedometer (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Speed Meter Operation Speedometer 0, 40, 80, 120, 160, 200 km/h Confirm that the vehicle is stopped with the engine idling.

OK:

Speedometer indication is normal.




OK

3.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED METER)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED METER)
a.

Use the Data List to check if the speedometer is operating properly (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed/Min.: 0 mph (0 km/h), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed measured using a speedometer tester -

OK:

Vehicle speed displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).




OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.READ VALUE USING INTELLIGENT TESTER (FR/FL/RR/RL WHEEL SPEED)
4.READ VALUE USING INTELLIGENT TESTER (FR/FL/RR/RL WHEEL SPEED)
a.

Use the Data List to check the wheel speed (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRAC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Vehicle speed/Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph) Almost the same as actual vehicle speed measured using a speedometer tester -
FL Wheel Speed Vehicle speed/Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph) Almost the same as actual vehicle speed measured using a speedometer tester -
RR Wheel Speed Vehicle speed/Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph) Almost the same as actual vehicle speed measured using a speedometer tester -
RL Wheel Speed Vehicle speed/Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph) Almost the same as actual vehicle speed measured using a speedometer tester -

OK:

Vehicle speed displayed on the intelligent tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).




OK

5.REPLACE MASTER CYLINDER SOLENOID

NG

5.REPLACE MASTER CYLINDER SOLENOID
a.

Replace the skid control ECU with a new or normally functioning one (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER>DISASSEMBLY).

OK:

The operation of the speedometer returns to normal.




OK

END

NG

REPLACE COMBINATION METER ASSEMBLY