Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The fuel sender gauge has a variable resistance mechanism. The resistance decreases when the fuel amount increases, and the resistance increases when the fuel amount decreases. The fuel receiver gauge changes based on the resistance of the fuel sender gauge.


NOTICE:

When the combination meter is removed or replaced, its connector is disconnected or fuel is added, the fuel receiver gauge display will return to normal within a maximum of 16 minutes after the ignition switch is turned to ON or when vehicle speed is input.


WIRING DIAGRAM

E200742E02
4.005,0.578 4.190,0.725 0.185,0.148 10 40 4.011,0.98 4.196,1.127 0.185,0.148 10 19 4.289,0.578 4.393,0.725 0.104,0.148 10 L 4.289,0.98 4.480,1.127 0.191,0.148 10 E3 3.682,0.578 3.786,0.725 0.104,0.148 10 2 3.682,0.98 3.786,1.127 0.104,0.148 10 3 3.382,0.578 3.580,0.725 0.197,0.148 10 FS 3.36,0.98 3.557,1.127 0.197,0.148 10 FE 1.824,3.573 2.158,3.720 0.334,0.148 10 ECM 1.47,1.475 3.382,1.656 1.913,0.181 10 Fuel Sender Gauge Assembly 0.748,1.988 0.989,2.135 0.241,0.148 10 Q5 0.744,2.167 3.979,2.356 3.234,0.190 10 Fuel Suction with Pump and Gauge Tube Assembly 4.209,4.136 6.054,4.284 1.846,0.148 10 Combination Meter Assembly 4.217,3.965 4.495,4.113 0.278,0.148 10 F14 0.749,4.288 2.598,4.435 1.849,0.148 10 : CAN Communication Line 4.916,1.407 5.278,1.554 0.362,0.148 10 CPU 5.504,1.737 5.899,1.885 0.394,0.148 10 FUEL 2.918,0.989 3.022,1.137 0.104,0.148 10 3 1.828,0.989 1.932,1.137 0.104,0.148 10 2

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).


Result
Result Proceed to
CAN communication DTC is not output A
CAN communication DTC is output B


A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL METER OPERATION)
a.

Use the Active Test to check the operation of the fuel receiver gauge (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge Empty, 1/2, Full Confirm that the vehicle is stopped with the engine idling.

OK:

Fuel receiver gauge indication is normal.




OK

3.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)

NG

REPLACE COMBINATION METER ASSEMBLY

3.READ VALUE USING INTELLIGENT TESTER (FUEL INPUT)
a.

Use the Data List to check if the fuel receiver gauge is operating properly (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input signal/Min.: 0, Max.: 127.5 Current fuel level displayed Unit: Liters

OK:

Fuel level signal displayed on the intelligent tester is almost the same as fuel receiver gauge indication.




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND BODY GROUND)

NG

REPLACE COMBINATION METER ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SUCTION WITH PUMP AND BODY GROUND)
a.

Disconnect the F14 meter connector.


b.

Disconnect the Q5 gauge connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-40 (L) - Q5-2 (FS) Always Below 1 Ω
F14-19 (E3) - Q5-3 (FE) Always Below 1 Ω
F14-40 (L) - Body ground Always 10 kΩ or higher
F14-19 (E3) - Body ground Always 10 kΩ or higher




OK

5.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
E180164E06
0.037,0 0.207,0.165 0.170,0.165 10 *a 1.641,0.274 1.818,0.419 0.177,0.144 10 *c 0.037,2.202 0.231,2.364 0.194,0.162 10 *b 1.641,2.807 1.818,2.972 0.177,0.165 10 *d 1.346,1.28 0.607,1.28 false 0.344,1.2 0.555,1.356 0.211,0.156 10 FE 2.28,0.438 2.492,0.594 0.211,0.156 10 FS 1.736,1.188 2.229,0.524 false

a.

Remove the fuel suction with pump and gauge tube assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 Always Below 1 Ω
A-3 (FE) - B-3



Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)
*b Lower Side (to Fuel Sender Gauge Assembly)
*c Connector A
*d Connector B


OK

6.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

6.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
A223150E02
0.532,2.522 0.698,2.669 0.166,0.147 10 *b 1.854,2.607 0.743,2.607 false 0.53,4.33 0.700,4.477 0.170,0.147 10 *c 1.699,4.415 0.743,4.415 false 0.695,0.7 0.885,0.847 0.190,0.147 10 *a

Remove the fuel sender gauge assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3 Float level F (upper) 12 to 18 Ω
Float level E (lower) 405 to 415 Ω



Text in Illustration
*a Front view of wire harness connector
(to Fuel Sender Gauge Assembly)
*b Float level F (upper)
*c Float level E (lower)


OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY