Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1440E _58 Vehicle Interior _056160 SUPPLEMENTAL RESTRAINT SYSTEMS _0274089 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1810/53  Short in Driver Side Squib 2nd Step Circuit  B1811/53  Open in Driver Side Squib 2nd Step Circuit  B1812/53  Short to GND in Driver Side Squib 2nd Step Circuit  B1813/53  Short to B+ in Driver Side Squib 2nd Step Circuit  


DESCRIPTION

The driver side squib 2nd step circuit consists of the center airbag sensor, spiral cable and steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.

DTC Code DTC Detection Condition Trouble Area
B1810/53 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the driver side squib 2nd step circuit during the primary check.

·

A driver side squib 2nd step malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1811/53 One of the following conditions is met:
·

The center airbag sensor detects an open circuit signal in the driver side squib 2nd step circuit for 2 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1812/53 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly


B1813/53 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds.

·

A driver side squib 2nd step malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib 2nd step)

·

Center airbag sensor assembly



WIRING DIAGRAM

U149912E03
0.646,3.198 2.396,3.375 1.75,0.177 10 false Driver Side Squib 2nd Step 2.51,3.021 2.802,3.167 0.292,0.146 10 false F24 0.667,3.021 0.958,3.167 0.292,0.146 10 false z13 2.51,3.177 3.292,3.385 0.781,0.208 10 false Spiral Cable 2.896,1.594 3.177,1.781 0.281,0.188 10 false D2+ 4.833,1.656 5.115,1.844 0.281,0.188 10 false D2+ 2.896,2.417 3.177,2.604 0.281,0.188 10 false D2- 4.844,2.51 5.125,2.698 0.281,0.188 10 false D2- 3.25,1.594 3.396,1.76 0.146,0.167 10 false 4 3.25,2.406 3.406,2.563 0.156,0.156 10 false 3 4.583,1.531 4.698,1.698 0.115,0.167 10 false 8 4.583,2.375 4.708,2.542 0.125,0.167 10 false 7 4.76,4.146 5.135,4.333 0.375,0.188 10 false F33 4.75,4.313 6.198,4.521 1.448,0.208 10 false Center Airbag Sensor 2.5,1.583 2.729,1.771 0.229,0.188 10 false 2 2.5,2.417 2.677,2.604 0.177,0.188 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral cable and steering wheel, be sure to adjust the spiral cable as it may break if the steering wheel is turned before adjusting the spiral cable (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP)
a.
U150082E03
2.052,2.292 2.427,2.51 false 0.198,0.823 0.198,1.219 false 1.823,2.771 2.198,3.135 false 0.135,1.219 0.323,1.396 0.188,0.177 10 false *1 0.76,1.208 0.938,1.385 0.177,0.177 10 false *2 1.573,1.51 1.76,1.688 0.188,0.177 10 false *a 2.177,1.26 2.354,1.438 0.177,0.177 10 false *3 2.49,2.438 2.667,2.615 0.177,0.177 10 false *5 2.26,3.063 2.448,3.24 0.188,0.177 10 false *b 2.635,1.979 2.813,2.156 0.177,0.177 10 false *4 2.344,0.677 2.469,0.854 0.125,0.177 10 false A 1.792,0.917 1.917,1.094 0.125,0.177 10 false C 1.667,0.917 1.792,1.094 0.125,0.177 10 false D 0.521,0.896 0.646,1.073 0.125,0.177 10 false E 0.323,0.906 0.448,1.083 0.125,0.177 10 false F 0.688,2.271 0.938,2.427 0.25,0.156 10 false z13

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the steering pad.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1810, B1811, B1812 or B1813 is not output.


HINT:

Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Driver Side Squib 2nd Step
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector E
*5 SST
*a Front view of wire harness connector
(to Driver Side Squib 2nd Step)
*b Color: Black



OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.
C214772E01
0.6,1.234 0.775,1.427 0.174,0.193 10 F 0.808,1.234 1.029,1.492 0.221,0.258 10 E 1.833,1.234 2.026,1.474 0.193,0.239 10 D 0.413,0.801 0.606,0.968 0.193,0.167 10 *1 1.035,1.561 1.228,1.729 0.193,0.167 10 *2 2.285,1.561 2.478,1.729 0.193,0.167 10 *3 1.946,1.234 2.157,1.455 0.211,0.221 10 C 2.456,0.976 2.649,1.159 0.193,0.184 10 A

Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Driver Side Squib 2nd Step
*2 Spiral Cable
*3 Center Airbag Sensor



OK

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT
U150084E03
0.198,0.823 0.198,1.219 false 1.844,2.75 2.219,3.115 false 1.635,2.125 1.177,2.604 false 1.74,2.125 2.167,2.604 false 0.146,1.208 0.333,1.385 0.188,0.177 10 false *1 0.76,1.208 0.938,1.385 0.177,0.177 10 false *2 1.573,1.51 1.76,1.688 0.188,0.177 10 false *a 2.417,1.25 2.594,1.427 0.177,0.177 10 false *3 2.26,3.031 2.448,3.208 0.188,0.177 10 false *b 2.635,1.979 2.813,2.156 0.177,0.177 10 false *4 0.448,2.25 0.708,2.417 0.26,0.167 10 false z13 2.552,0.656 2.677,0.833 0.125,0.177 10 false A 1.792,0.906 1.917,1.083 0.125,0.177 10 false C 2.198,0.906 2.323,1.083 0.125,0.177 10 false B 1.667,0.906 1.792,1.083 0.125,0.177 10 false D 0.542,0.906 0.667,1.083 0.125,0.177 10 false E 0.313,0.906 0.438,1.083 0.125,0.177 10 false F 0.885,2.531 1.135,2.677 0.25,0.146 10 false D2- 2.198,2.51 2.49,2.656 0.292,0.146 10 false D2+

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z13-2 (D2+) - Body ground Ignition switch ON Below 1 V
z13-1 (D2-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z13-2 (D2+) - z13-1 (D2-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z13-2 (D2+) - z13-1 (D2-) Always 1 MΩ or higher
z13-2 (D2+) - Body ground Always 1 MΩ or higher
z13-1 (D2-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Driver Side Squib 2nd Step
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector E
*a Front view of wire harness connector
(to Driver Side Squib 2nd Step)
*b Color: Black


OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
4.CHECK CENTER AIRBAG SENSOR
a.
C146246E17
0.323,1.271 0.323,0.75 false 0.417,0.823 0.542,1.021 0.125,0.198 10 false F 0.542,0.823 0.667,1.021 0.125,0.198 10 false E 1.615,0.833 1.771,1.021 0.156,0.188 10 false D 1.75,0.833 1.917,1.01 0.167,0.177 10 false C 0.771,1.281 0.927,1.458 0.156,0.177 10 false *2 0.208,1.313 0.385,1.479 0.177,0.167 10 false *1 2.135,1.281 2.302,1.438 0.167,0.156 10 false *3

Connect the connectors to the steering pad and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1810, B1811, B1812 or B1813 is not output.


HINT:

Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Driver Side Squib 2nd Step
*2 Spiral Cable
*3 Center Airbag Sensor



OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
a.
U150086E01
1.444,0.1 1.628,0.274 0.184,0.174 10 *1 0.759,1.24 0.934,1.419 0.175,0.179 10 *2 1.576,1.539 1.759,1.714 0.184,0.174 10 *a 2.178,1.24 2.353,1.419 0.175,0.179 10 *3 2.636,2.009 2.810,2.188 0.175,0.179 10 *4 0.424,2.239 0.681,2.409 0.257,0.170 10 F24 2.349,0.655 2.478,0.834 0.130,0.179 10 A 1.664,0.912 1.793,1.091 0.130,0.179 10 C 1.99,0.912 2.120,1.091 0.130,0.179 10 B 1.475,0.912 1.604,1.091 0.130,0.179 10 D 0.442,0.912 0.571,1.091 0.130,0.179 10 E 0.249,0.912 0.379,1.091 0.130,0.179 10 F 1.891,0.683 1.891,0.193 1.891,0.193 1.65,0.193 false 0.888,2.792 1.181,2.941 0.292,0.149 10 D2+ 2.343,2.801 2.597,2.949 0.253,0.149 10 D2- 1.448,2.391 1.244,2.872 false 1.63,2.391 2.312,2.872 false

Restore the released activation prevention mechanism of connector B to its original condition.


b.

Disconnect the instrument panel wire connector from the spiral cable.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F24-4 (D2+) - Body ground Ignition switch ON Below 1 V
F24-3 (D2-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F24-4 (D2+) - F24-3 (D2-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F24-4 (D2+) - F24-3 (D2-) Always 1 MΩ or higher
F24-4 (D2+) - Body ground Always 1 MΩ or higher
F24-3 (D2-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Instrument Panel Wire
*2 Spiral Cable
*3 Center Airbag Sensor
*4 Connector C
*5 SST
*a Rear view of wire harness connector
(to Spiral Cable)


OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE