Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2009.08–2013.08
RM1440E _58 Vehicle Interior _056162 SEAT BELT _0274120 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter detects the state of the front seat inner belt RH when the front passenger seat is occupied with the ignition switch ON. If the front passenger seat belt is not fastened, the front passenger side seat belt warning light of the telltale light blinks. If the seat belt is fastened, the warning light goes off.

WIRING DIAGRAM

C217625E01
0.497,1.33 1.503,1.514 1.006,0.184 10 from IG2 Relay 4.099,0.912 4.243,1.079 0.144,0.167 10 6 5.548,1.061 6.287,1.245 0.739,0.184 10 P/SB 5.548,2.968 6.287,3.152 0.739,0.184 10 PBKL 3.355,1.344 3.737,1.527 0.382,0.184 10 LAPB 3.653,1.046 4.035,1.230 0.382,0.184 10 LAPL 4.556,3.571 4.700,3.739 0.144,0.167 10 2 3.297,3.591 3.442,3.759 0.144,0.167 10 3 3.297,2.836 3.442,3.004 0.144,0.167 10 1 4.56,2.836 4.704,3.004 0.144,0.167 10 3 3.157,4.329 3.491,4.529 0.334,0.200 10 N3 3.157,4.531 4.747,4.702 1.590,0.171 10 Front Seat Inner Belt RH 3.27,1.86 3.604,2.060 0.334,0.200 10 F35 3.27,2.062 4.210,2.233 0.940,0.171 10 Telltale Light 5.419,3.665 5.753,3.865 0.334,0.200 10 F14 5.419,3.867 6.697,4.038 1.279,0.171 10 Combination Meter 3.137,1.222 3.265,1.395 0.128,0.173 10 7 5.239,0.933 5.440,1.092 0.201,0.159 10 35 5.259,2.859 5.449,3.018 0.189,0.159 10 34 3.689,3.15 4.222,3.467 0.532,0.317 10 Buckle Switch 1.549,4.531 2.857,4.885 1.308,0.354 10 Occupant Detection Sensor 2.272,1.533 2.965,1.722 0.693,0.188 10 IGN 4.352,2.843 4.528,2.995 0.175,0.152 10 + 4.352,3.578 4.528,3.730 0.175,0.152 10 E

CAUTION / NOTICE / HINT

HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Check the Data List for proper functioning of the front passenger side seat belt buckle switch (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger side seat belt buckle signal / ON or OFF ON: Front passenger side seat belt fastened
OFF: Front passenger side seat belt unfastened
-

OK:

The display is as specified in the normal condition column.




OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT)

NG

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT PASSENGER SIDE SEAT BELT WARNING LIGHT)
a.

Operate the intelligent tester according to the display and select Active Test (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>DATA LIST / ACTIVE TEST).

Combination Meter
Item Test Part Control Range Diagnostic Note
Front passenger side seat belt Front passenger side seat belt warning light ON/OFF Confirm that the vehicle is stopped and the engine is idling.

Result
Result Proceed to
Front passenger side seat belt warning light condition cannot be switched by Active Test A
Front passenger side seat belt warning light condition can be switched by Active Test B



A

3.INSPECT TELLTALE LIGHT ASSEMBLY

B

REPLACE COMBINATION METER ASSEMBLY

3.INSPECT TELLTALE LIGHT ASSEMBLY
a.
C197122E07
1.375,1.177 1.667,1.604 true 1.208,1.167 1.063,1.604 true 0.833,1.604 1.219,1.771 0.385,0.167 10 false LAPB 1.5,1.604 1.885,1.771 0.385,0.167 10 false LAPL

Remove the telltale light (See page Vehicle Interior>SEAT BELT>FRONT PASSENGER SEAT BELT WARNING LIGHT>REMOVAL).


b.

Apply battery voltage to the telltale light.


c.

Check that the front passenger side seat belt warning light comes on.

OK
Measurement Condition Specified Condition
Battery positive (+) → Terminal 7 (LAPB)
Battery negative (-) → Terminal 6 (LAPL)
Front passenger side seat belt warning light comes on



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - TELLTALE LIGHT, BATTERY AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - TELLTALE LIGHT, BATTERY AND BODY GROUND)
a.

Disconnect the F14 meter connector.


b.

Disconnect the F35 telltale light connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-35 (P/SB) - F35-6 (LAPL) Always Below 1 Ω
F14-35 (P/SB) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F35-7 (LAPB) - Body ground Ignition switch ON 11 to 14 V




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)
a.
C213678

Remove the front seat assembly (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 More than 147 N (15 kgf, 33.0 lbf) applied to occupant detection sensor Below 100 Ω




OK

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION PAD (OCCUPANT DETECTION SENSOR)

6.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
a.
C213676E12
1.698,1.198 1.604,1.656 true 1.885,1.198 2,1.719 true 1.531,1.677 1.74,1.875 0.208,0.198 10 false + 1.969,1.74 2.177,1.938 0.208,0.198 10 false E

Remove the front seat inner belt assembly RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (E) - 3 Always Below 1 Ω
3 (+) - 1 Front passenger side seat belt unfastened
3 (+) - 1 Front passenger side seat belt fastened 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT RH AND BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - FRONT SEAT INNER BELT RH AND BODY GROUND)
a.

Disconnect the F14 meter connector.


b.

Disconnect the N3 inner belt connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-34 (PBKL) - N3-3 (+) Always Below 1 Ω
N3-2 (E) - Body ground
F14-34 (PBKL) - Body ground Always 10 kΩ or higher




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR