Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
73370C
1.INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
Align the claws with the seat belt positioning holes and install the retractor of the seat belt with the bolt as shown in the illustration.
First install bolt A, and then install bolt B.
Install the rear No. 1 seat outer belt shoulder anchor with the bolt.
72602B
2.INSTALL REAR NO. 2 SEATBACK LOCK STRIKER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat)
62560C
3.INSTALL REAR WINDOW SIDE GARNISH ASSEMBLY LH
62580F
4.INSTALL REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH
64740C
5.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
w/o Rear No. 2 Seat:
Pass the rear seatback lock control lever base through the deck trim side panel.
Attach the 4 claws and 2 guides to install the rear seatback lock control lever base to the deck trim side panel.
Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.
Install the 3 bolts and 2 screws.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
w/ Rear No. 2 Seat:
Attach the 7 clips, 5 claws and 2 guides to install the deck trim side panel.
Install the 3 bolts and 2 screws.
Install the rear No. 1 seat outer belt floor anchor with the bolt.
for LH Side:
Install the rear No. 2 seat outer belt floor anchor with the bolt.
Do not allow the anchor part of the anchor plate sub-assembly to overlap the protruding parts of the vehicle body.
| *a | Protruding Part |
for RH Side:
Install the rear No. 2 seat outer belt floor anchor with the bolt.
Do not allow the anchor part of the anchor plate sub-assembly to overlap the protruding parts of the vehicle body.
| *a | Protruding Part |
64721B
6.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER
64713F
7.INSTALL FRONT DECK SIDE TRIM COVER LH
64725J
8.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
73233A
9.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
58570C
10.INSTALL REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)
58574A
11.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
58306A
12.INSTALL INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)
58410R
13.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)
58704A
14.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)
58703A
15.INSTALL LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)
58480B
16.INSTALL REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)
58408D
17.INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)
64722B
18.INSTALL NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board, w/o Rear No. 2 Seat)
Use the same procedure for all No. 2 luggage compartment trim covers.
Install the luggage hold belt striker and No. 2 luggage compartment trim cover with the bolt.
Attach the 2 claws to close the cover.
58401A
19.INSTALL NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)
64721B
20.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)
62332C
21.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
67918D
22.INSTALL REAR DOOR SCUFF PLATE LH
67934
23.INSTALL QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)