Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274151 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1422/22  Compressor Lock Sensor Circuit  


SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the cooler compressor assembly is locked and turns the magnet clutch assembly off.

DTC Code DTC Detection Condition Trouble Area
B1422/22 Open or short in the compressor lock sensor circuit.
·

Cooler compressor assembly (A/C lock sensor)

·

Compressor drive belt

·

Harness or connector

·

Air conditioning amplifier assembly

·

CAN communication system



WIRING DIAGRAM

E193114E23
1.74,0.615 2.104,0.813 0.365,0.198 10 false ECM 5.396,1.781 5.844,1.938 0.448,0.156 10 false LOCK 5.406,2.792 5.802,2.958 0.396,0.167 10 false SG-2 3.073,1.688 3.25,1.865 0.177,0.177 10 false 1 1.74,1.688 1.917,1.865 0.177,0.177 10 false 2 1.688,2.313 4.792,2.51 3.104,0.198 10 false Cooler Compressor Assembly (A/C Lock Sensor) 4.896,3.417 7.135,3.625 2.24,0.208 10 false Air Conditioning Amplifier Assembly 5.156,1.677 5.313,1.823 0.156,0.146 10 false 8 5.094,2.677 5.281,2.854 0.188,0.177 10 false 13 1.688,2.125 2.094,2.313 0.406,0.188 10 false B41 4.917,3.25 5.229,3.406 0.313,0.156 10 false F42 0.844,3.469 2.521,3.667 1.677,0.198 10 false CAN Communication Line

CAUTION / NOTICE / HINT

HINT:

As DTC B1422/22 is also output when the compressor drive belt is damaged or loose, inspect the belt before performing troubleshooting.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output B



A

2.INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

B

2.INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)
a.
E193115

Remove the cooler compressor assembly (A/C lock sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 160 to 320 Ω




OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C LOCK SENSOR)

NG

REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C LOCK SENSOR)
a.

Disconnect the F42 amplifier connector.


b.

Disconnect the B41 sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F42-8 (LOCK) - B41-1 Always Below 1 Ω
F42-13 (SG-2) - B41-2 Always Below 1 Ω
F42-8 (LOCK) - Body ground Always 10 kΩ or higher
F42-13 (SG-2) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR