Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274152 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  Air Conditioning Compressor Magnetic Clutch Circuit  


DESCRIPTION

When the air conditioning amplifier assembly is turned on, a magnet clutch assembly ON signal is sent from the MGC terminal of the air conditioning amplifier assembly. Then, the A/C COMP relay turns on to operate the magnet clutch assembly.

WIRING DIAGRAM

E198320E24
6.052,1.604 6.438,1.76 0.385,0.156 10 false MGC 5.458,5.146 7.104,5.531 1.646,0.385 10 false Air Conditioning Amplifier Assembly 4.375,3.813 4.542,4 0.167,0.188 10 false 3 3.271,3.802 3.375,4 0.104,0.198 10 false 1 1.604,4.594 2.75,4.927 1.146,0.333 10 false Magnet Clutch Assembly 3.26,4.604 4.563,5.01 1.302,0.406 10 false Cooler Compressor Assembly 2.208,1.5 2.354,1.667 0.146,0.167 10 false 1 3.115,1.51 3.219,1.708 0.104,0.198 10 false 2 3.094,1.021 3.219,1.177 0.125,0.156 10 false 3 2.219,1.01 2.344,1.177 0.125,0.167 10 false 5 2.344,1.99 3.25,2.135 0.906,0.146 10 false A/C COMP 2.281,3.083 3.313,3.25 1.031,0.167 10 false from Battery 2.271,2.667 3.802,2.833 1.531,0.167 10 false from IG1 NO. 1 Relay 5.74,1.51 5.938,1.656 0.198,0.146 10 false 20 5.469,4.948 5.771,5.125 0.302,0.177 10 false F42 1.615,4.385 1.823,4.531 0.208,0.146 10 false A 3.25,4.396 3.563,4.542 0.313,0.146 10 false B41 3.969,3.813 4.333,3.969 0.365,0.156 10 false MG+ 1.323,1.781 1.604,1.948 0.281,0.167 10 false IG1 1.125,1.271 2.031,1.417 0.906,0.146 10 false A/C COMP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT MAGNET CLUTCH RELAY (A/C COMP)
a.
E145138

Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

2.INSPECT COOLER COMPRESSOR ASSEMBLY

NG

REPLACE MAGNET CLUTCH RELAY (A/C COMP)

2.INSPECT COOLER COMPRESSOR ASSEMBLY
a.
U116491E02
1.708,1.146 1.917,1.583 1.917,1.583 2.167,1.583 true 0.656,2.438 0.906,2.604 0.25,0.167 10 false A 2.188,1.5 2.563,1.667 0.375,0.167 10 false MG+

Remove the cooler compressor assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL).


b.

Disconnect the A magnet clutch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MG+) - A-1 Always Below 1 Ω
3 (MG+) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAGNETIC CLUTCH ASSEMBLY

NG

REPLACE COOLER COMPRESSOR ASSEMBLY

3.INSPECT MAGNETIC CLUTCH ASSEMBLY
a.
E198322E02
1.302,1.802 1.646,1.396 true 1.083,1.833 1.448,2.01 0.365,0.177 10 false MG+

Reconnect the A magnet clutch connector.


b.

Apply battery voltage to the magnet clutch assembly and check the operation of the magnet clutch assembly.

OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 3 (MG+)
Battery negative (-) → Body ground
Magnet clutch assembly operating sound can be heard, and magnetic clutch hub and rotor lock.




OK

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)

NG

4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - BATTERY)
a.
E200501E01
0.083,0.042 0.336,0.211 0.253,0.170 10 *a 1.802,1.801 2.055,1.970 0.253,0.170 10 *1

Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A/C COMP relay terminal 1 - Body ground Ignition switch ON 11 to 14 V
A/C COMP relay terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 A/C COMP Relay
*a Component without relay installed
(Engine Room No. 1 Relay Block, Junction Block)



OK

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - BATTERY)
a.
U181018E02
2.802,2.417 2.51,3.031 true 0.125,0.042 0.385,0.26 0.26,0.219 10 false *a 0.625,1.281 0.927,1.479 0.302,0.198 10 false F42 2.323,3.063 2.677,3.26 0.354,0.198 10 false MGC

Disconnect the F42 amplifier connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F42-20 (MGC) - Body ground Ignition switch off Below 1 V
F42-20 (MGC) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - COOLER COMPRESSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 1 RELAY BLOCK, JUNCTION BLOCK - COOLER COMPRESSOR)
a.

Remove the A/C COMP relay from the engine room No. 1 relay block, junction block.


b.

Disconnect the B41 compressor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/C COMP relay terminal 3 - B41-3 (MG+) Always Below 1 Ω
B41-3 (MG+) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR