Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2013.08
RM1440E _58 Vehicle Interior _056165 INTERIOR PANELS / TRIM _0274158 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 2.REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

Hide 67920 3.REMOVE DOOR SCUFF PLATE ASSEMBLY LH

a.
B240006E03
1.948,2.688 2.021,3.115 true 2.021,3.115 2.125,3.115 false 2.219,2.688 2.531,3.24 true 2.531,3.24 2.604,3.24 false 2.135,3.031 2.323,3.25 0.188,0.219 10 false *1 2.615,3.156 2.802,3.375 0.188,0.219 10 false *1

Put protective tape around the door scuff plate assembly LH.

Text in Illustration
*1 Protective Tape


b.

Using a screwdriver, detach the 4 clips, 10 claws and 2 guides to remove the door scuff plate assembly LH.

HINT:

Tape the screwdriver tip before use.



Hide 67910 4.REMOVE DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH

a.
B238734

Remove the clip.


b.

Detach the clip and claw to remove the cowl side trim board LH.


Hide 62111C 6.REMOVE COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 7.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B240007

Remove the front door opening trim weatherstrip LH.


Hide 62311B 8.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 74617A 9.REMOVE ASSIST GRIP PLUG

a.
B238813E03
1.813,1.208 2.573,1.667 true 2.573,1.667 2.677,1.667 false 2.698,1.573 2.875,1.938 0.177,0.365 10 false *1

Using a screwdriver, detach the 2 claws to remove the assist grip plug.

Text in Illustration
*1 Protective Tape

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for the other assist grip plug.




Hide 74611F 10.REMOVE NO. 1 ASSIST GRIP

a.
B238814

Remove the 2 bolts.


b.

Detach the 2 claws to remove the No. 1 assist grip.


Hide 62211 11.REMOVE FRONT PILLAR GARNISH RH

a.
B240014

Detach the clip and 3 guides to remove the front pillar garnish RH.


b.
B240016E02
0.927,0.688 1.042,0.688 false 1.042,0.688 1.5,1.219 false 0.51,1.5 0.635,1.5 false 0.635,1.5 1.271,2.615 true 1.979,1.635 2.677,2.302 true 2.677,2.302 2.823,2.302 false 2.823,2.198 3.083,2.438 0.26,0.24 10 false *1 0.771,0.604 1.031,0.844 0.26,0.24 10 false *2 0.333,1.417 0.594,1.656 0.26,0.24 10 false *3

Protect the curtain shield airbag assembly.

i.

Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.

Text in Illustration
*1 Curtain Shield Airbag Assembly
*2 Adhesive Tape
*3 Protective Cover

NOTICE:

Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.




Hide 62212 12.REMOVE FRONT PILLAR GARNISH LH

a.
B353464E02
1.552,1.115 1.875,1.448 false 1.917,1.396 2.167,1.625 0.25,0.229 10 false *1

Using a screwdriver, detach the 2 claws to remove the No. 1 front pillar garnish cover LH.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



b.
B353465

Remove the bolt.


c.

Detach the clip.


d.
B353468

Detach the 2 guides to remove the front pillar garnish LH.


e.
B240015E02
0.604,1.469 0.76,1.469 false 0.76,1.469 1.073,0.969 true 1.875,0.979 2.302,0.625 false 2.302,0.625 2.469,0.625 false 1.865,2.865 2.646,2.052 true 2.646,2.052 2.75,2.052 false 0.448,1.385 0.698,1.677 0.25,0.292 10 false *1 2.458,0.521 2.708,0.813 0.25,0.292 10 false *2 2.802,1.969 3.052,2.26 0.25,0.292 10 false *3

Protect the curtain shield airbag assembly.

i.

Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.

Text in Illustration
*1 Curtain Shield Airbag Assembly
*2 Adhesive Tape
*3 Protective Cover

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.




Hide 58371F 13.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)

a.
B238730E06
1.646,1.26 2.042,1.51 true 2.042,1.51 2.146,1.51 false 2.146,1.417 2.375,1.604 0.229,0.188 10 true *1

Using a screwdriver, detach the 2 claws to remove the rear No. 1 floor step cover.

Text in Illustration
*1 Protective Tape

HINT:
·

Tape the screwdriver tip before use.

·

Use the same procedure for all the rear No. 1 floor step covers.




Hide 67934 14.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)

a.
B238731

Remove the 2 bolts and quarter scuff plate LH.


Hide 67933 15.REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 67918D 16.REMOVE REAR DOOR SCUFF PLATE LH

a.

Put protective tape around the rear door scuff plate LH.


b.
B240011E04
1.677,2.771 1.792,3.104 1.792,3.104 1.917,3.104 false 2.229,2.625 2.344,3.198 2.344,3.198 2.458,3.198 false 2.49,3.104 2.646,3.26 0.156,0.156 10 false *1 1.927,3 2.083,3.177 0.156,0.177 10 false *1

Using a screwdriver, detach the 3 clips, 6 claws and 2 guides to remove the rear door scuff plate LH.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 67917C 17.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62332C 18.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B240009

Remove the rear door opening trim weatherstrip LH.


Hide 62331C 19.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 20.REMOVE OUTER LAP BELT ANCHOR COVER

a.
B238735

Detach the 3 claws to remove the outer lap belt anchor covers.

HINT:

Use the same procedure for the other outer lap belt anchor cover.



Hide 62414A 21.REMOVE LOWER CENTER PILLAR GARNISH LH

a.
B238736

Remove the bolt to disconnect the front seat outer belt floor anchor.


b.
B238737

Detach the 4 claws and 2 clips to remove the lower center pillar garnish LH.


Hide 62413A 22.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62412 23.REMOVE CENTER PILLAR GARNISH LH

a.
B240017

Move the front shoulder belt anchor adjuster to the lowest position.


b.

Remove the bolt.


c.

Detach the 2 clips and 2 guides.


d.

Pass the front seat outer belt floor anchor through the center pillar garnish LH to remove the center pillar garnish LH.


Hide 62411 24.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 64721B 25.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board)

a.
B240044

Detach the 4 claws to open the covers.


b.
B240045E02
2.083,1.156 2.594,0.948 true 2.594,0.948 2.719,0.948 false 2.729,0.865 2.958,1.021 0.229,0.156 10 false *1

Remove the bolt, luggage hold belt striker and No. 1 luggage compartment trim cover.

Text in Illustration
*1 Luggage Hold Belt Striker

HINT:

Use the same procedure for the other No. 1 luggage compartment trim cover.



Hide 58401A 26.REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board)

a.
B240046

Detach the clip to remove the No. 1 deck board sub-assembly.


Hide 58704A 27.REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board)

a.
B240062E02
2.802,1 3.135,0.219 true 3.135,0.219 2.979,0.219 false 2.813,0.146 3.031,0.438 0.219,0.292 10 false *1

Using a screwdriver, detach the 4 clips and 2 guides to remove the luggage compartment side cover sub-assembly LH.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 58703A 28.REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board)

HINT:

Use the same procedure as for the LH side.


Hide 58410R 29.REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)

a.
B353466

Remove the 6 bolts.


b.

Detach the 2 guides to remove the deck board assembly.


Hide 64722B 30.REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board)

a.
B240048

Detach the 2 claws to open the cover.


b.
B240049E02
2.073,1.021 2.625,0.552 true 2.625,0.552 2.781,0.552 false 2.771,0.427 3,0.625 0.229,0.198 10 false *1

Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.

Text in Illustration
*1 Luggage Hold Belt Striker

HINT:

Use the same procedure for the other No. 2 luggage compartment trim cover.



Hide 58408D 31.REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

a.
B240064

Detach the 2 clips and 2 guides to remove the No. 2 deck board sub-assembly.


Hide 58480B 32.REMOVE REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board)

a.
B240065

Detach the 3 clips to remove the rear No. 2 floor board assembly.


Hide 58306A 33.REMOVE INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board)

a.
B353467

Remove the 4 bolts and inner floor side rail sub-assembly.


Hide 58574A 34.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

a.
B240050

Detach the 5 clips to remove the rear floor mat rear support plate.


Hide 58570C 35.REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board)

a.
B240047

Detach the 4 claws to remove the rear floor carpet assembly.


Hide 73233A 36.REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

a.
B240053

Detach the 3 claws to remove the rear No. 1 seat outer lap belt anchor cover.

HINT:

Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.



Hide 64725J 37.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

a.
B181695

Remove the No. 1 luggage compartment trim hook by turning it clockwise.

HINT:

Use the same procedure for the other No. 1 luggage compartment trim hook.



Hide 64713F 38.REMOVE FRONT DECK SIDE TRIM COVER LH

a.
B240051E03
1.615,1.479 2.167,1.844 false 2.167,1.844 2.333,1.844 false 2.333,1.75 2.615,1.917 0.281,0.167 10 false *1

Using a screwdriver, detach the 2 claws to remove the front deck side trim cover LH.

Text in Illustration
*1 Protective Tape

HINT:

Tape the screwdriver tip before use.



Hide 64712F 39.REMOVE FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 64722B 40.REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)

a.
B240048

Detach the 2 claws to open the cover.


b.
B240049E02
2.073,1.021 2.625,0.552 true 2.625,0.552 2.781,0.552 false 2.771,0.427 3,0.625 0.229,0.198 10 false *1

Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.

Text in Illustration
*1 Luggage Hold Belt Striker

HINT:

Use the same procedure for the other No. 2 luggage compartment trim cover.



Hide 64740C 41.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH

a.

w/o Rear No. 2 Seat:

i.
B240054

Remove the bolt to disconnect the rear No. 1 seat outer belt floor anchor.


ii.

Remove the 3 bolts and 2 screws.


iii.

Detach the 7 clips, 5 claws and 2 guides.

B240058


iv.
B238756

Detach the 6 claws and 2 guides and pass the rear seatback lock control lever base through the deck trim side panel assembly LH to remove the deck trim side panel assembly LH.



b.

w/ Rear No. 2 Seat:

i.
B240054

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.
B240052

Remove the bolt to disconnect the rear No. 2 seat outer belt floor anchor.


iii.

Remove the 3 bolts and 2 screws.


iv.

Detach the 7 clips, 5 claws and 2 guides to remove the deck trim side panel assembly LH.

B240060



Hide 64730B 42.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

a.

w/o Rear No. 2 Seat:

i.
B240057

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.

Remove the 3 bolts and screw.


iii.

Detach the 7 clips, 5 claws and 2 guides.

B240059


iv.

Disconnect the connector.


v.
B238823

Detach the 6 claws and 2 guides and pass the rear seatback lock control lever base through the deck trim side panel assembly RH to remove the deck trim side panel assembly RH.



b.

w/ Rear No. 2 Seat:

i.
B240057

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


ii.
B240055

Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.


iii.

Remove the 3 bolts and screw.


iv.

Detach the 7 clips, 5 claws and 2 guides.


v.

Disconnect the connector and remove the deck trim side panel assembly RH.

B240061



Hide 62580F 43.REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH

a.

w/o Rear No. 2 Seat:

i.
B240018

Detach the 6 clips and guide to remove the rear No. 2 window side garnish assembly LH.



b.

w/ Rear No. 2 Seat:

i.
B241940

Detach the 6 clips and guide.


ii.
B240019

Detach the 7 claws and guide and pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish assembly LH to remove the rear No. 2 window side garnish assembly LH.



Hide 62570D 44.REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62560C 45.REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY LH

a.
B240020

Detach the 7 clips and 4 guides.


b.
B240021

Detach the 4 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish assembly LH to remove the rear window side garnish assembly LH.


Hide 62550F 46.REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74610A 47.REMOVE ASSIST GRIP SUB-ASSEMBLY

a.
B203052E10
0.49,1.563 0.615,1.563 false 0.615,1.563 0.76,1.354 false 1.188,3.75 1.438,3.75 false 1.427,3.75 1.146,3.281 true 0.323,1.479 0.521,1.76 0.198,0.281 10 false *1 1.021,3.656 1.219,3.938 0.198,0.281 10 false *1

Using a clip remover, detach the 4 claws.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not forcibly pry the assist grip plugs to prevent them from being deformed.


HINT:
·

Gently pry the assist grip plugs as shown in the illustration to detach the claws.

·

Tape the clip remover tip before use.

·

Use the same procedure for the other assist grip sub-assembly.




b.

Pull off the 2 assist grip plugs by hand.


c.
B203053

Detach the 2 clips to remove the assist grip sub-assembly.


d.

Remove the 2 clips from the vehicle body.


Hide 74610U 48.REMOVE REAR ASSIST GRIP ASSEMBLY

a.
B203054E05
1.104,3.854 1.323,3.854 false 1.323,3.854 1.094,3.25 true 0.844,1.344 0.656,1.542 false 0.656,1.542 0.552,1.542 false 0.396,1.469 0.573,1.75 0.177,0.281 10 false *1 0.948,3.781 1.125,4.063 0.177,0.281 10 false *1

Using a clip remover, detach the 4 claws.

Text in Illustration
*1 Protective Tape

NOTICE:

Do not forcibly pry the assist grip plugs to prevent them from being deformed.


HINT:
·

Gently pry the rear assist grip plugs as shown in the illustration to detach the claws.

·

Tape the clip remover tip before use.

·

Use the same procedure for the other rear assist grip assembly.




b.

Pull off the 2 assist grip plugs by hand.


c.
B203055

Detach the 2 clips to remove the rear assist grip assembly.


d.

Remove the 2 clips from the vehicle body.


Hide 74631C 49.REMOVE COAT HOOK

a.
B240022E03
1.99,1.271 2.438,1.719 false 2.448,1.719 2.563,1.719 false 2.594,1.625 2.865,1.948 0.271,0.323 10 false *1

Using a screwdriver, detach the claw to open the cover.

Text in Illustration
*1 Protective Tape


b.
B240023

Remove the screw and coat hook.

HINT:

Use the same procedure for the other coat hook.



Hide 74318 50.REMOVE VISOR BRACKET COVER LH

a.
B181706

Detach the 4 claws to remove the visor bracket cover LH.


Hide 74317 51.REMOVE VISOR BRACKET COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 74320 52.REMOVE VISOR ASSEMBLY LH

a.
B181707

Remove the 2 screws and visor assembly LH.


Hide 74310 53.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74348 54.REMOVE VISOR HOLDER

a.
B151362E13
0.813,0.563 1.135,0.771 0.323,0.208 10 false 45°

Turn the visor holder approximately 45° to pull it out as shown in the illustration.


b.

Detach the 2 claws to remove the visor holder.

HINT:

Use the same procedure for the other visor holder.



Hide 87834 56.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 81240 57.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 63310 58.REMOVE ROOF HEADLINING ASSEMBLY

HINT:
B240031

Before removing the roof headlining assembly, move the front seats and rear No. 1 seat to the positions shown in the illustration.


a.
B354490

w/ EC Mirror:

Disconnect the inner rear view mirror assembly connector.


b.
B240024

w/ Sliding Roof:

Disconnect the sliding roof drive gear connector.


c.
B360654

Disconnect each connector and detach the 4 clamps from the front pillar LH.


d.
B240026

Disconnect the connector and detach the 2 clamps from the front pillar RH.


e.
B240027

Disconnect the connector and detach the clamp from the rear pillar RH.


f.
B354450

w/o Sliding Roof:

i.

Remove the 5 clips.



g.
B354451E03
1.354,1.271 1.948,1.646 1.948,1.646 1.354,1.99 true 1.354,1.51 1.948,1.646 1.948,1.646 1.354,1.75 true 0.813,2.208 1.302,2.875 1.302,2.875 1.24,2.219 true 0.813,1.031 1.313,0.427 1.313,0.427 1.24,1.021 true 0.479,1.26 0.479,0.281 0.479,0.281 0.667,0.281 false 0.49,2 0.49,3.031 0.49,3.031 0.625,3.031 false 1.99,1.563 2.156,1.729 0.167,0.167 10 false *2 1.25,2.906 1.417,3.073 0.167,0.167 10 false *2 1.26,0.229 1.427,0.396 0.167,0.167 10 false *2 0.708,0.198 0.875,0.365 0.167,0.167 10 false *1 0.677,2.938 0.844,3.104 0.167,0.167 10 false *1

w/ Sliding Roof:

i.

Remove the 5 clips.


ii.

Detach the 2 guides and 8 fasteners.

Text in Illustration
*1 Guide
*2 Fastener



h.
B240030

Remove the roof headlining assembly from the back door as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining assembly when removing it.



Hide 73024 59.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

a.
B240077

Detach the 4 claws of the front shoulder belt anchor plate sub-assembly LH to slide the front shoulder belt anchor plate sub-assembly LH to remove it.


Hide 73023 60.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62440 61.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH

a.
B240066

Detach the 3 clips to remove the roof side rail garnish assembly LH.


Hide 62430 62.REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 66426B 63.REMOVE REAR NO. 3 SIDE RAIL SPACER LH

a.
B240068

Detach the 2 claws to remove the rear No. 3 side rail spacer LH.


Hide 66416 64.REMOVE REAR NO. 3 SIDE RAIL SPACER RH

HINT:

Use the same procedure as for the LH side.


Hide 62627B 65.REMOVE QUARTER TRIM COVER

a.
B240071

Detach the 2 claws to remove the quarter trim cover.

HINT:

Use the same procedure for the other quarter trim cover.



Hide 64766 66.REMOVE QUARTER TRIM JACK COVER SUB-ASSEMBLY

a.
B240073

Detach the 3 claws and 2 guides to remove the quarter trim jack cover sub-assembly.


Hide 64746 67.REMOVE REAR COMBINATION LIGHT SERVICE COVER LH

a.
B240072

Detach the 2 claws and 2 guides to remove the rear combination light service cover LH.


Hide 64745 68.REMOVE REAR COMBINATION LIGHT SERVICE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 62597A 69.REMOVE SIDE TRIM BOX LH (w/o Rear No. 2 Seat)

a.
B240070

Remove the 2 screws.


b.

Detach the 8 claws to remove the side trim box LH.


Hide 62597A 70.REMOVE SIDE TRIM BOX RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 64754B 71.REMOVE REAR FLOOR FINISH SIDE PLATE LH (w/o Rear No. 2 Seat)

a.
B240074

Remove the 2 screws.


b.

Detach the claw and 2 guides to remove the rear floor finish side plate LH.


Hide 64753B 72.REMOVE REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 73372 73.REMOVE REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 2 Seat)

a.
B238782

Detach the claw and guide to remove the rear seat shoulder belt hanger LH.


Hide 73371 74.REMOVE REAR SEAT SHOULDER BELT HANGER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.


Hide 62605Q 75.REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH (w/ Rear No. 2 Seat)

a.
B240075

Detach the 4 claws and 2 guides to remove the quarter trim lid sub-assembly RH.


Hide 64746F 76.REMOVE DECK SIDE TRIM CUP HOLDER LH (w/ Rear No. 2 Seat)

a.
B240076

Remove the 4 screws.


b.

Detach the 2 claws to remove the deck side trim cup holder LH.


Hide 64745H 77.REMOVE DECK SIDE TRIM CUP HOLDER RH (w/ Rear No. 2 Seat)

HINT:

Use the same procedure as for the LH side.