When the back door power window is fully closed and the rear window defogger switch is turned on, a rear window defogger activation request signal is sent via the LIN communication line to the air conditioning amplifier.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Since the window defogger system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.
Since the window defogger system does not operate if the back power window is not operating normally, confirm that the back power window of the power window system is operating normally before performing troubleshooting.
Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>WINDOW / GLASS>WINDOW DEFOGGER SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Defogger Relay (Rear) | DEF relay operation | OFF/ON | - |
The DEF relay operates normally.
OK
NG
Temporarily replace the heater control with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL).
Check the rear defogger function.
The window defogger function operates normally.
OK
NG
Remove the DEF relay from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage applied between terminals 1 and 2 | Below 1 Ω |
| 3 - 5 | Battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
OK
NG
Remove the DEF relay from the engine room relay block, junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| DEF relay terminal 2 - Body ground | Ignition switch off | Below 1 V |
| DEF relay terminal 2 - Body ground | Ignition switch ON | 11 to 14 V |
| DEF relay terminal 5 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to DEF Relay) |
OK
NG
Disconnect the F42 air conditioning amplifier connector.
Remove the DEF relay from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEF relay terminal 1 - F42-38 (RDEF) | Always | Below 1 Ω |
| F42-14 (GND) - Body ground | Always | Below 1 Ω |
| F42-38 (RDEF) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the F42 air conditioning amplifier connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F42-38 (RDEF) - F42-14 (GND) | Ignition switch ON, defogger switch on | 11 to 14 V |
| F42-38 (RDEF) - F42-14 (GND) | Ignition switch ON, defogger switch off | Below 1 V |
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
OK
NG
Disconnect the W1 and W2 back door glass (window defogger wire) connectors.
Remove the DEF relay from the engine room relay block, junction block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DEF relay terminal 3 - W1-1 | Always | Below 1 Ω |
| W2-1 - Body ground | Always | Below 1 Ω |
| W1-1 - Body ground | Always | 10 kΩ or higher |
OK
NG