Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274161 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Rear Power Window RH does not Operate with Rear Power Window Switch RH  


DESCRIPTION

If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, rear power window regulator motor, harness or connector.


WIRING DIAGRAM

B242537E23
0.333,4.479 0.719,4.479 false 0.719,4.438 0.333,4.438 false 0.719,4.458 0.333,4.458 false 2.615,3.75 2.875,3.927 0.26,0.177 10 false i1 4.771,3.781 5.063,3.979 0.292,0.198 10 false J2 1.469,0.615 4.438,0.802 2.969,0.188 10 false Main Body ECU (Multiplex Network Body ECU) 0.271,1.125 1.094,1.313 0.823,0.188 10 false from Battery 1.854,1.292 2.573,1.469 0.719,0.177 10 false DOOR RR 5.406,1.146 5.531,1.323 0.125,0.177 10 false B 5.188,0.979 5.313,1.156 0.125,0.177 10 false 2 5.406,1.667 5.75,1.844 0.344,0.177 10 false GND 5.188,1.531 5.313,1.708 0.125,0.177 10 false 1 5.406,2.302 5.75,2.479 0.344,0.177 10 false UP 5.125,2.156 5.313,2.333 0.188,0.177 10 false 10 5.406,2.719 5.885,2.896 0.479,0.177 10 false DOWN 3.833,2.302 4.063,2.479 0.229,0.177 10 false UP 3.104,3.167 3.5,3.344 0.396,0.177 10 false GND 3.583,2.719 4.063,2.896 0.479,0.177 10 false DOWN 5.198,2.604 5.302,2.781 0.104,0.177 10 false 7 4.177,2.156 4.365,2.333 0.188,0.177 10 false 6 4.177,2.604 4.354,2.781 0.177,0.177 10 false 7 2.885,3.063 3,3.208 0.115,0.146 10 false 1 0.75,4.375 2.396,4.563 1.646,0.188 10 false : LIN Communication Line 2.615,3.938 4.583,4.542 1.969,0.604 10 false Rear Power Window Regulator Switch Assembly RH 4.781,3.958 6.771,4.448 1.99,0.49 10 false Rear Power Window Regulator Motor Assembly RH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC (B2312)
a.

Check if DTC B2312 is output (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>B2312).

OK:

DTC B2312 is not output.




OK

2.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (REAR POWER WINDOW REGULATOR SWITCH)
a.

Use the Data List to check if the rear power window regulator motor is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

RR-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door P/W Up SW Rear power window RH manual up signal / ON or OFF ON: Rear power window RH manual up switch operated
OFF: Rear power window RH switch not operated
-
RR Door P/W Down SW Rear power window RH manual down signal / ON or OFF ON: Rear power window RH manual down switch operated
OFF: Rear power window RH switch not operated
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW)

NG

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER WINDOW)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that power window regulator motor operates (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

RR-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Rear RH side power window OFF/UP/DOWN -

OK:

The power window regulator motor operates normally.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.
B215963E16
2.692,0.371 3.077,0.569 0.385,0.198 10 GND 2.309,1.729 2.549,1.899 0.239,0.170 10 UP 0.617,1.716 1.106,1.893 0.489,0.177 10 DOWN 2.12,0.973 2.494,0.462 2.494,0.462 2.666,0.462 false 1.854,1.312 2.09,1.815 2.09,1.815 2.262,1.815 false 1.592,1.312 1.356,1.815 1.356,1.815 1.184,1.815 false

Remove the rear power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (UP) - 1 (GND) Manual up operation Below 1 Ω
7 (DOWN) - 1 (GND) Manual down operation Below 1 Ω
6 (UP) - 1 (GND) Not operated 10 kΩ or higher
7 (DOWN) - 1 (GND) Not operated 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BODY GROUND)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BODY GROUND)
a.
B216018E08
0.588,0.983 0.772,1.187 0.184,0.205 10 i1 1.465,1.047 1.121,1.67 1.121,1.67 0.992,1.67 false 0.587,1.591 0.921,1.736 0.334,0.144 10 GND 0.197,0.176 0.376,0.355 0.179,0.179 10 *a

Disconnect the i1 rear power window regulator switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly RH)



OK

6.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the i1 rear power window regulator switch connector.


b.

Disconnect the J2 rear power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-6 (UP) - J2-10 (UP) Always Below 1 Ω
i1-7 (DOWN) - J2-7 (DOWN) Always Below 1 Ω
i1-6 (UP) - Body ground Always 10 kΩ or higher
i1-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND)
a.
B216019E09
0.526,0.949 0.783,1.118 0.257,0.170 10 J2 0.178,0.141 0.344,0.300 0.166,0.159 10 *a 1.579,0.79 1.222,0.476 1.222,0.476 1.115,0.476 false 1.871,0.79 2.228,0.476 2.228,0.476 2.335,0.476 false 0.706,0.399 1.053,0.548 0.347,0.149 10 GND 2.374,0.399 2.554,0.673 0.180,0.274 10 B

Disconnect the J2 rear power window regulator motor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J2-2 (B) - Body ground Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
J2-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Rear Power Window Regulator Motor Assembly RH)



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR