Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274161 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:

·

The ECU in the power window regulator motor determines that the power window regulator motor has not been initialized.

·

The power window regulator switch has a malfunction.

·

The Hall IC in the power window regulator motor has a malfunction.

·

There is an open or short in the wiring between the power window regulator switch and power window regulator motor.


WIRING DIAGRAM

B240839E11
0.156,3.531 0.5,3.531 false 0.49,3.448 0.156,3.448 false 0.156,3.49 0.49,3.49 false 4.979,2.427 5.333,2.594 0.354,0.167 10 false H2 1.875,2.333 2.125,2.521 0.25,0.188 10 false g1 0.542,3.406 2.188,3.563 1.646,0.156 10 false : LIN Communication Line 1.24,0.979 4.229,1.188 2.99,0.208 10 false Main Body ECU (Multiplex Network Body ECU) 2.958,1.938 3.396,2.094 0.438,0.156 10 false AUTO 5.385,1.938 5.823,2.094 0.438,0.156 10 false AUTO 3.5,1.823 3.615,1.979 0.115,0.156 10 false 8 5.146,1.823 5.26,1.979 0.115,0.156 10 false 4 1.875,1.823 1.99,1.979 0.115,0.156 10 false 1 2.052,1.938 2.406,2.094 0.354,0.156 10 false GND 1.896,2.51 3.5,2.927 1.604,0.417 10 false Power Window Regulator Switch Assembly 4.99,2.625 7.031,3.042 2.042,0.417 10 false Front Power Window Regulator Motor Assembly RH

CAUTION / NOTICE / HINT

HINT:

Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Result
Result Proceed to
DTC is not output A
DTC B2311 is output B
DTC B2312 is output C
DTC B2313 is output D



A

2.CHECK MANUAL UP/DOWN FUNCTION (POWER WINDOW REGULATOR SWITCH)

B

C

D

2.CHECK MANUAL UP/DOWN FUNCTION (POWER WINDOW REGULATOR SWITCH)
a.

Check that the manual up/down function using the front power window regulator switch can operate the front power window (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Front passenger side door power window moves.




OK

3.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR SWITCH)

NG

GO TO "Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch"

3.READ VALUE USING INTELLIGENT TESTER (POWER WINDOW REGULATOR SWITCH)
a.

Use the Data List to check if the front power window regulator is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger side power window auto up/down signal / ON or OFF ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window regulator switch not operated
-

OK:

On tester screen, item changes between ON and OFF according to above chart.




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B215963E18
2.692,0.363 3.077,0.560 0.385,0.198 10 GND 0.462,1.708 0.882,1.884 0.420,0.177 10 AUTO 2.12,0.964 2.494,0.453 2.494,0.453 2.666,0.453 false 1.386,1.304 1.149,1.806 1.149,1.806 0.977,1.806 false

Remove the power window regulator switch (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (AUTO) - 1 (GND) Auto up/down operation Below 1 Ω
8 (AUTO) - 1 (GND) Not operated 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR RH AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR RH AND BODY GROUND)
a.

Disconnect the g1 power window regulator switch connector.


b.

Disconnect the H2 power window regulator motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g1-8 (AUTO) - H2-4 (AUTO) Always Below 1 Ω
g1-1 (GND) - Body ground Always Below 1 Ω
g1-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR