Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2013.08
RM1440E _59 Vehicle Exterior _056166 WINDOW / GLASS _0274169 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 53883F 3.REMOVE FRONT FENDER MAIN SEAL LH

Hide 53882H 4.REMOVE FRONT FENDER MAIN SEAL RH

Hide 53867H 5.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 6.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

Hide 85292B 7.REMOVE FRONT WIPER ARM HEAD CAP

Hide 8.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 9.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 55781E 10.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 67920 11.REMOVE DOOR SCUFF PLATE ASSEMBLY LH

Hide 67910 12.REMOVE DOOR SCUFF PLATE ASSEMBLY RH

Hide 62112 13.REMOVE COWL SIDE TRIM BOARD LH

Hide 62111C 14.REMOVE COWL SIDE TRIM BOARD RH

Hide 62312B 15.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 16.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62211 19.REMOVE FRONT PILLAR GARNISH RH

Hide 62212 20.REMOVE FRONT PILLAR GARNISH LH

Hide 74610A 21.REMOVE ASSIST GRIP SUB-ASSEMBLY

Hide 87810 28.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87834 29.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 87810 30.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 63310 31.REMOVE ROOF HEADLINING ASSEMBLY

a.

Partially remove the roof headlining assembly.

HINT:

It is not necessary to completely remove the roof headlining assembly. Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed in a later step.

Refer to the following procedures (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).



Hide 75533E 32.REMOVE WINDSHIELD OUTSIDE MOULDING

a.
B166392E03
1.656,0.594 1.656,0.656 true 1.063,0.354 1.531,0.885 false 0.781,1.625 1.167,1.333 false 2.406,0.188 2.24,0.188 2.24,0.188 2.24,0.948 false 1.656,0.698 1.656,0.771 true 1.656,0.833 1.656,0.906 true 1.656,0.958 1.656,1.021 true 1.656,1.094 1.656,1.188 true 1.677,1.24 1.677,1.323 true 1.677,1.365 1.677,1.427 true 1.552,0.333 1.74,0.49 0.188,0.156 10 false *a 2.469,0.094 2.667,0.292 0.198,0.198 10 false *1 0.594,1.667 0.781,1.823 0.188,0.156 10 false *3 0.844,0.25 1.073,0.406 0.229,0.156 10 false *2

Using a knife, cut off the windshield outside moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Remove the remaining windshield outside moulding.

Text in Illustration
*1 Windshield Glass
*2 Windshield Outside Upper Moulding
*3 Vehicle Body
*a Cut

HINT:

Make a partial cut in the windshield outside moulding. Then pull and remove it by hand.



Hide 75533G 33.REMOVE WINDSHIELD OUTSIDE UPPER MOULDING

a.
U149681E02
2.094,1.177 2.563,1.177 false 1,0.865 0.875,0.271 0.875,0.271 0.646,0.271 false 0.427,0.177 0.656,0.396 0.229,0.219 10 false *1 2.49,0.083 2.719,0.302 0.229,0.219 10 false *2 2.656,1.104 2.885,1.323 0.229,0.219 10 false *3 1.656,0.365 1.885,0.583 0.229,0.219 10 false *a

Using a knife, cut off the windshield outside upper moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.



b.

Pull the shaded area shown in the illustration by hand to remove the windshield outside upper moulding.

Text in Illustration
*1 Windshield Glass
*2 Windshield Outside Upper Moulding
*3 Vehicle Body
*a Cut

HINT:

Make a partial cut in the windshield outside upper moulding. Then pull and remove it by hand.



Hide 56111 34.REMOVE WINDSHIELD GLASS

NOTICE:
·

There are No. 1 and No. 2 windshield glass stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

·

To prevent the windshield glass from dropping when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle specifications, a 1-piece or 2- piece type stopper is used.


B238992E02
1.635,0.927 1.417,0.865 false 5.146,0.781 4.958,0.781 false 5.458,0.708 5.625,0.958 5.625,0.958 5.729,0.958 false 1.781,0.25 2,0.5 0.219,0.25 10 false *A 5.479,0.24 5.698,0.49 0.219,0.25 10 false *B 1.26,0.771 1.49,0.99 0.229,0.219 10 false *1 4.833,0.708 5.063,0.927 0.229,0.219 10 false *1 5.76,0.854 5.99,1.073 0.229,0.219 10 false *2

Text in Illustration
*A for 1-piece Type *B for 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper

a.
B238993E01
0.451,0.208 0.671,0.419 0.221,0.211 10 *1 1.274,0.543 0.686,0.288 false

Apply protective tape around the windshield glass on the vehicle body.

Text in Illustration
*1 Protective Tape

HINT:

Apply protective tape to the installation surface to prevent it from being scratched.



b.
B183897E05
1.25,0.302 1.552,0.302 1.552,0.302 1.552,0.979 false 2.177,1.729 2.177,2.104 false 1.104,2.75 1.323,3.156 1.323,3.156 1.604,3.156 false 2.344,2.74 2.146,3.146 2.146,3.146 1.875,3.146 false 1.698,3.573 1.698,4.083 false 1.042,0.219 1.26,0.406 0.219,0.188 10 false *1 2.094,2.115 2.313,2.26 0.219,0.146 10 false *2 1.656,3.094 1.844,3.281 0.188,0.188 10 false *3 1.615,4.094 1.833,4.26 0.219,0.167 10 false *4

From the interior, insert a piano wire between the vehicle body and windshield glass as shown in the illustration.


c.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

Text in Illustration
*1 Plastic Sheet
*2 Protective Tape
*3 Windshield Glass Stopper
*4 Piano Wire

NOTICE:
·

When separating the windshield glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and instrument panel.




d.
B166394E03
0.885,1.156 1.063,1.156 false 1.083,1.073 1.26,1.271 0.177,0.198 10 false *a

Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.

Text in Illustration
*a Matchmark

NOTICE:

Matchmarks do not need to be placed if not reusing the windshield glass.



e.

w/ Windshield Deicer System:

Disconnect the windshield deicer connector.


f.

Cut through the adhesive by pulling the piano wire around the windshield glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when removing the windshield glass.



g.

Disconnect the stoppers.


h.
B166840

Using suction cups, remove the windshield glass.


Hide 56117D 35.REMOVE WINDSHIELD GLASS ADHESIVE DAM

a.

Using a scraper, remove the windshield glass adhesive dam.


Hide 56115A 36.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

Using a scraper, remove the 2 No. 1 windshield glass stoppers.


Hide 56116C 37.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:

Be sure to replace the No. 2 windshield glass stoppers with new ones.



Hide 56115A 38.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B238995

Remove the 2 No. 1 windshield glass stoppers.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 56111 39.CLEAN WINDSHIELD GLASS

a.
B106929

Using a scraper, remove the damaged windshield glass stoppers, windshield glass adhesive dam and adhesive sticking to the windshield glass.


b.

Clean the outer circumference of the windshield glass with non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Be careful not to damage the windshield glass.

·

Even if using new windshield glass, clean the windshield glass with non-residue solvent.




Hide 40.CLEAN VEHICLE BODY

a.
B106081E23
0.49,1.313 0.771,0.719 0.771,0.719 0.948,0.719 true 2.271,1.438 2.552,0.74 2.552,0.74 2.719,0.74 true 2.427,1.615 2.427,1.792 false 0.813,1.563 0.813,1.75 false 1.01,0.646 1.25,0.844 0.24,0.198 10 false *1 2.771,0.677 3.01,0.875 0.24,0.198 10 false *1 0.719,1.76 0.958,1.958 0.24,0.198 10 false *2 2.344,1.802 2.583,2 0.24,0.198 10 false *2

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

Text in Illustration
*1 Adhesive
*2 Vehicle Body

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.