Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM › 2009.08–2016.12
RM1440E _59 Vehicle Exterior _056167 SLIDING ROOF / CONVERTIBLE _0274174 SLIDING ROOF SYSTEM J

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF SYSTEM  Sliding Roof Control Switch Circuit  


DESCRIPTION

The sliding roof drive gear sub-assembly receives sliding roof switch signals and drives its built-in motor.

WIRING DIAGRAM

B240414E04
3.597,2.173 4.059,2.355 0.462,0.182 10 OPN 1.94,2.209 2.297,2.390 0.357,0.182 10 OPN 3.596,2.509 4.121,2.691 0.525,0.182 10 CLS 1.972,2.517 2.314,2.699 0.342,0.182 10 CLS 3.603,2.812 4.066,2.993 0.462,0.182 10 UP 3.566,5.128 4.028,5.310 0.462,0.182 10 S8 0.857,3.512 1.319,3.694 0.462,0.182 10 U2 2.047,2.83 2.280,3.012 0.233,0.182 10 UP 3.596,3.134 4.107,3.316 0.511,0.182 10 DWN 1.804,3.133 2.315,3.314 0.511,0.182 10 DOWN 4.305,2.653 5.124,3.028 0.820,0.376 10 Sliding Roof ECU 5.34,1.522 6.567,1.731 1.227,0.209 10 Sliding Roof Motor 0.847,3.673 2.429,3.952 1.582,0.278 10 Map Light Assembly 0.957,3.925 2.469,4.203 1.512,0.278 10 - Sliding Roof Switch 3.561,5.288 6.066,5.469 2.505,0.181 10 Sliding Roof Drive Gear Sub-assembly 5.621,2.403 6.109,2.612 0.488,0.209 10 Hall IC 5.621,3.161 6.109,3.370 0.488,0.209 10 Hall IC 3.372,2.203 3.491,2.352 0.120,0.149 10 7 2.37,2.207 2.489,2.356 0.120,0.149 10 3 2.37,2.523 2.489,2.673 0.120,0.149 10 2 2.37,2.831 2.489,2.981 0.120,0.149 10 5 2.37,3.147 2.489,3.297 0.120,0.149 10 4 0.69,2.367 0.810,2.517 0.120,0.149 10 1 3.372,2.532 3.491,2.681 0.120,0.149 10 9 3.313,2.831 3.509,2.980 0.196,0.149 10 10 3.372,3.146 3.491,3.296 0.120,0.149 10 8 3.372,4.158 3.491,4.307 0.120,0.149 10 2 3.589,4.162 3.843,4.332 0.254,0.170 10 E 0.863,2.347 1.252,2.517 0.389,0.170 10 GND

CAUTION / NOTICE / HINT

NOTICE:

When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIDING ROOF)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the sliding roof slides open/closed and tilts up/down (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Test Part Control Range Diagnostic Note
Slide Roof Operate sliding roof Opn/Dwn: Sliding roof slide open or tilt down operation occurs
Clos/Up: Sliding roof slide close or tilt up operation occurs
OFF: Sliding roof not operating
-

OK:

The sliding roof operates normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF)

NG

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

2.READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>DATA LIST / ACTIVE TEST).

Sliding Roof
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Open Switch Slide open switch signal / ON or OFF ON: Slide open switch pressed
OFF: Slide open switch not pressed
-
Close Switch Slide close switch signal / ON or OFF ON: Slide close switch pressed
OFF: Slide close switch not pressed
-
Up Switch Tilt up switch signal / ON or OFF ON: Tilt up switch pressed
OFF: Tilt up switch not pressed
-
Down Switch Tilt down switch signal / ON or OFF ON: Tilt down switch pressed
OFF: Tilt down switch not pressed
-

OK:

When operating the switch, the intelligent tester displays as shown in the table.




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

3.INSPECT MAP LIGHT ASSEMBLY
3.INSPECT MAP LIGHT ASSEMBLY
E198779E08
2.115,1.167 2.333,0.552 true 1.948,1.167 1.698,0.542 true 1.719,1.167 1.177,0.677 true 2.552,0.813 2.229,1.177 true 1.51,1.75 1.844,1.24 true 0.125,0.073 0.375,0.25 0.25,0.177 10 false *a 2.552,0.615 2.917,0.792 0.365,0.177 10 false GND 1.5,0.344 1.938,0.521 0.438,0.177 10 false OPN 2.219,0.344 2.542,0.521 0.323,0.177 10 false CLS 1.198,1.76 1.688,1.938 0.49,0.177 10 false DOWN 0.969,0.542 1.208,0.719 0.24,0.177 10 false UP

a.

Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (UP) - 1 (GND) Tilt up switch pressed Below 1 Ω
5 (UP) - 1 (GND) Tilt up switch not pressed 10 kΩ or higher
4 (DOWN) - 1 (GND) Tilt down switch pressed Below 1 Ω
4 (DOWN) - 1 (GND) Tilt down switch not pressed 10 kΩ or higher
3 (OPN) - 1 (GND) Slide open switch pressed Below 1 Ω
3 (OPN) - 1 (GND) Slide open switch not pressed 10 kΩ or higher
2 (CLS) - 1 (GND) Slide close switch pressed Below 1 Ω
2 (CLS) - 1 (GND) Slide close switch not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Map Light Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)

NG

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)
a.

Disconnect the S8 ECU connector.


b.

Disconnect the U2 map light connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S8-10 (UP) - U2-5 (UP) Always Below 1 Ω
S8-8 (DWN) - U2-4 (DOWN) Always Below 1 Ω
S8-7 (OPN) - U2-3 (OPN) Always Below 1 Ω
S8-9 (CLS) - U2-2 (CLS) Always Below 1 Ω
U2-1 (GND) - Body ground Always Below 1 Ω
S8-2 (E) - Body ground Always Below 1 Ω
S8-10 (UP) or U2-5 (UP) - Body ground Always 10 kΩ or higher
S8-8 (DWN) or U2-4 (DOWN) - Body ground Always 10 kΩ or higher
S8-7 (OPN) or U2-3 (OPN) - Body ground Always 10 kΩ or higher
S8-9 (CLS) or U2-2 (CLS) - Body ground Always 10 kΩ or higher




OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR