Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF HOUSING
RM1440E _59 Vehicle Exterior _056167 SLIDING ROOF / CONVERTIBLE _0274175 SLIDING ROOF HOUSING A

SLIDING ROOF / CONVERTIBLE  SLIDING ROOF HOUSING  INSTALLATION  


PROCEDURE

Hide 63203F 1.INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY

a.

Temporarily install the housing with the 8 bolts (vehicle body side) and 8 nuts.


b.

Tighten the 8 nuts in alphabetical order.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Tighten the 8 bolts in alphabetical order.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

B234371E02
2.406,1.531 2.542,1.729 0.135,0.198 10 false A 4.313,2.729 4.438,2.906 0.125,0.177 10 true B 0.719,1.188 0.854,1.385 0.135,0.198 10 false C 3.25,3.083 3.385,3.281 0.135,0.198 10 false D 1.01,2.188 1.146,2.385 0.135,0.198 10 false E 2.521,3.031 2.656,3.229 0.135,0.198 10 false F 1.406,2.438 1.542,2.635 0.135,0.198 10 false G 1.958,2.75 2.094,2.948 0.135,0.198 10 false H 3.823,1.229 3.969,1.438 0.146,0.208 10 false a 5.385,2.188 5.5,2.354 0.115,0.167 10 true b 3.094,1.635 3.24,1.844 0.146,0.208 10 false c 4.76,2.781 4.906,2.99 0.146,0.208 10 false d 2.896,1.75 3.042,1.958 0.146,0.208 10 false e 4.646,2.438 4.76,2.615 0.115,0.177 10 true f 2.177,1.656 2.323,1.865 0.146,0.208 10 false g 3.667,3.063 3.813,3.271 0.146,0.208 10 false h


d.

Connect the 4 sliding roof drain hoses.


Hide 63251H 2.INSTALL SLIDING ROOF WEATHERSTRIP

a.

Install the sliding roof weatherstrip as described below.

i.

Attach each corner of the weatherstrip so that each weatherstrip mark is aligned with the sliding roof glass center mark. After attaching the entire weatherstrip, check that all weatherstrip marks are within the sliding roof glass end marks.


ii.

Make sure the weatherstrip cutout is toward the rear side of the vehicle and centered.


iii.

Make sure the weatherstrip is securely installed as shown in the illustration.

B234384E02
1.427,1.427 1.531,0.979 1.531,0.979 1.667,0.979 false 1.698,0.906 2.313,1.156 0.615,0.25 10 false *a 1.115,1.531 1.396,1.792 0.281,0.26 10 false *b 3.833,0.24 4.135,0.479 0.302,0.24 10 false *c 3.844,1.323 4.135,1.542 0.292,0.219 10 false *d

Text in Illustration
*a Cutout *b Rear Side
*c CORRECT *d INCORRECT



Hide 63201G 3.INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY

a.
B178614

Using a T25 "TORX" driver, temporarily install the glass with the 4 screws.


b.

Perform a level check.

i.

Check the difference in the level between the roof panel and upper surface of the weatherstrip labeled "a" when the sliding roof glass is fully closed.

Standard:
Area Specified Condition
A - A 0 +/-1.5 mm (0 +/-0.0591 in.)
B - B
C - C
D - D


HINT:

"+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.



ii.

Perform a gap check.

Check the gap between the roof panel and roof glass.

NOTICE:

The gap must be even all around.


B234385E03
5.354,0.823 5.688,1 0.333,0.177 10 false Even 4.646,1.229 4.802,1.406 0.156,0.177 10 false a 1.885,1.885 2.042,2.063 0.156,0.177 10 false A 2.167,1.885 2.323,2.063 0.156,0.177 10 false A 2.438,1.896 2.594,2.073 0.156,0.177 10 false B 2.698,1.885 2.854,2.063 0.156,0.177 10 false B 2.302,2.354 2.417,2.51 0.115,0.156 10 true D 2.469,2.521 2.583,2.729 0.115,0.208 10 true D 2.052,1.083 2.208,1.26 0.156,0.177 10 true C 2.083,1.354 2.198,1.552 0.115,0.198 10 true C



c.
B178614

Tighten the 4 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 4.CHECK FOR WATER LEAK

a.

After adjusting the sliding roof glass sub-assembly, check for water leakage into the vehicle interior.

If there are any leaks, readjust the sliding roof glass sub-assembly.


Hide 63218G 5.INSTALL SLIDING ROOF SIDE GARNISH LH

B178613

a.

Attach the 5 claws to install the sliding roof side garnish.


Hide 63217K 6.INSTALL SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedures described for the LH side.


Hide 62180A 7.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

a.

Hide 62170A 8.INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 63310 9.INSTALL ROOF HEADLINING ASSEMBLY

a.

Install the roof headlining assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION).


Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 11.CHECK SRS WARNING LIGHT