Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY › 2009.08–2013.08
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274177 HOOD LOCK CONTROL CABLE ASSEMBLY A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 53630 1.INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY

a.
B184768E03
2.034,1.397 2.191,1.56 0.156,0.163 10 *1 2.568,1.482 2.218,1.482 false

Tie the string that was passed through the engine compartment to the end of the hood lock control cable assembly as shown in the illustration.

Text in Illustration
*1 String


b.

Pull the string until the hood lock control cable grommet contacts the dash panel, and then connect the clamps shown in the illustration to install the cable to the engine compartment.

U180712E02
0.781,0.5 0.99,0.5 false 1.177,0.5 1.115,0.5 1.115,0.5 1.052,0.781 true 2.063,0.896 2.063,0.76 2.063,0.76 2.177,0.667 false 2.688,0.458 2.646,0.458 2.646,0.458 2.552,0.656 false 1.354,2.146 1.51,2.146 1.51,2.146 1.573,2.365 true 5.844,0.708 6.042,0.708 6.042,0.708 6.083,0.948 false 5.625,1.188 5.917,1.188 false 6.094,2.135 6.302,2.135 6.302,2.135 6.354,2.323 false 6.104,2.708 6.271,2.708 false 1.948,1.365 1.948,1.219 1.948,1.219 1.604,1.104 false 1.927,1.219 2.271,1.073 false 2,0.917 2.167,1.083 0.167,0.167 10 false *2 1.854,1.396 2.021,1.563 0.167,0.167 10 false *4 2.74,0.375 2.906,0.542 0.167,0.167 10 false *1 1.24,0.417 1.406,0.583 0.167,0.167 10 false *2 0.625,0.417 0.792,0.583 0.167,0.167 10 false *1 1.198,2.073 1.365,2.24 0.167,0.167 10 false *1 1.729,0.26 1.958,0.469 0.229,0.208 10 false *a 5.938,2.063 6.104,2.229 0.167,0.167 10 false *1 5.677,0.625 5.844,0.792 0.167,0.167 10 false *1 5.458,1.115 5.625,1.281 0.167,0.167 10 false *3 5.938,2.625 6.104,2.792 0.167,0.167 10 false *3

Text in Illustration
*1 Hood Lock Control Cable *2 Stopper
*3 Wire Harness *4 Grommet
*a Engine Room Side - -


Hide 53601 2.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.

Connect the hood lock control cable assembly.


b.

Attach the 3 claws to install the hood lock control lever sub-assembly.


c.
B237118

Attach the clamp.


Hide 67920 4.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

Hide 53510 5.INSTALL HOOD LOCK ASSEMBLY

a.

Apply MP grease to the sliding areas of the lock.


b.

Connect the hood lock control cable assembly.


c.

w/ Engine Hood Courtesy Switch:

Connect the connector.


d.

w/o Engine Hood Courtesy Switch:

Connect the connector cap.


e.

Install the hood lock assembly with the 3 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 53629 6.INSTALL HOOD LOCK CONTROL CABLE COVER

a.
B237113

Pass the hood lock control cable assembly through the hood lock control cable cover.


b.

Attach the claw to install the hood lock control cable cover.


c.

Install the 2 screws.


Hide 86520 7.INSTALL LOW PITCHED HORN ASSEMBLY

Hide 86510 8.INSTALL HIGH PITCHED HORN ASSEMBLY