Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2009.08–2013.08
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274178 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 67001A 1.INSTALL FRONT DOOR PANEL CUSHION

a.

Attach the clip to install a new door panel cushion.


Hide 75756C 5.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 75712B 6.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 67862 7.INSTALL FRONT DOOR WEATHERSTRIP LH

a.

Attach the 21 clips to install a new front door weatherstrip.


Hide 68620 8.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding areas of the front door check assembly.


b.
B238556

Install the door check to the door panel with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the door check to the body panel with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 67924 9.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION

a.

Clean the installation surface.

i.

Using a heat light, heat the installation surface.

HINT:

When installing the front door No. 2 stiffener cushion, heat the vehicle body using a heat light.


Standard:
Item Temperature
Vehicle body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the door stiffener cushion and vehicle body excessively.



ii.

Remove the double-sided tape from the installation surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new door stiffener cushion.

i.

Using a heat light, heat a new front door No. 2 stiffener cushion and the installation surface.

HINT:

When installing the front door No. 2 stiffener cushion, heat the vehicle body and door stiffener cushion using a heat light.


Standard:
Item Temperature
Door stiffener cushion 20 to 30°C (68 to 86°F)
Vehicle body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the door stiffener cushion and vehicle body excessively.



ii.

Remove the peeling paper from the face of the door stiffener cushion.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Attach the 2 clamps and double-sided tape to install the front door No. 2 stiffener cushion.

HINT:

Press the front door No. 2 stiffener cushion firmly to install it.



iv.
B238555E03
2.365,1.135 2.125,1.135 2.125,1.135 1.74,0.708 true 2.396,1.063 2.604,1.26 0.208,0.198 10 false *1

Install the 2 bolts.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)

Text in Illustration
*1 Double-sided Tape



Hide 69312 10.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.
B241221E02
2.958,2.323 3.156,2.531 0.198,0.208 10 false (1) 2.167,1.927 2.365,2.135 0.198,0.208 10 true (2)

Install the front door lock open rod as indicated by the arrows in the order shown in the illustration.


Hide 69202A 11.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B240605

Attach the door handle nut and claw.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69242F 12.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD LH

a.

Attach the 2 claws to install the front door rear outside handle pad.


Hide 69241H 13.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

a.

Attach the 3 claws to install the front door front outside handle pad.


Hide 69220 14.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B240617

Insert the front end of the front door outside handle assembly into the front door outside handle frame.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame. Then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.
B240616

Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.


Hide 69760C 15.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the front door inside locking cable assembly.


b.

Attach the 3 claws.


Hide 69720B 16.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the front door lock remote control cable assembly.


Hide 69040A 17.INSTALL FRONT DOOR LOCK ASSEMBLY LH

Hide 69217E 18.INSTALL FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

a.
B240591

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Install the hole plug.


Hide 69217F 19.INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

a.
B241225

Attach the claw and install the front door outside handle cover to the front door lock cylinder.


Hide 20.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.

Install the front door outside handle cover with lock cylinder assembly.

HINT:

Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.



b.
B240589

Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Install the hole plug.


Hide 67404F 21.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B242327

Install the front door rear lower frame sub-assembly with the bolt as shown in the illustration.

Torque:
6.2 N*m (63 kgf*cm, 55 in.*lbf)


Hide 68151E 22.INSTALL FRONT DOOR GLASS RUN LH

a.

Install the front door glass run.


Hide 67664C 23.INSTALL DOOR FRAME GARNISH LH

a.
B240607

Attach the clip to install a new door frame garnish.


Hide 85720C 24.INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69802 25.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.

Install the temporary bolt to the front door window regulator assembly.


c.
B240585E03
1.917,1 2.031,1 2.031,1 2.135,1.24 true 2.667,2.021 2.948,2.24 0.281,0.219 10 true (1) 3.188,1.208 3.406,1.563 0.219,0.354 10 true (2) 3.104,1.979 3.365,2.229 0.26,0.25 10 true (3) 1.802,1.156 2.031,1.375 0.229,0.219 10 true (4) 1.75,0.917 2.063,1.385 0.313,0.469 10 true *1 1.458,2.406 1.667,2.677 0.208,0.271 10 true (5) 2.042,2.344 2.26,2.615 0.219,0.271 10 true (6)

Temporarily install the front door window regulator assembly.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the temporary bolt and 5 bolts to install the front door window regulator assembly.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 68102 26.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



d.
B240609E02
2.104,0.042 2.406,0.313 0.302,0.271 10 false (1) 0.396,0.323 0.625,0.594 0.229,0.271 10 true (2)

Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows in the order shown in the illustration.


e.
B240583E02
2.417,1.854 2.688,2.146 0.271,0.292 10 true (2) 1.646,1.896 2.042,2.167 0.396,0.271 10 true (1)

Install the front door glass sub-assembly with the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



Hide 87940 27.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 67832 28.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Apply butyl tape to the front door panel.


b.
B240610E02
0.208,0.208 0.417,0.427 0.208,0.219 10 false *1 3.083,0.219 3.292,0.438 0.208,0.219 10 false *1

Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.


c.

Install a new front door service hole cover according to the reference points on the front door panel.

Text in Illustration
*1 Reference Point

NOTICE:

Securely install the front door service hole cover preventing wrinkles and air bubbles.



d.
B240582

Attach the 2 clamps.


e.

Install the bolt to the front door wire.


Hide 84810 31.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84930 32.INSTALL DOOR CONTROL SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84040 33.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 68172A 34.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B240611

Install the front door inner glass weatherstrip.


Hide 81230 35.INSTALL FRONT DOOR COURTESY LIGHT ASSEMBLY LH

Hide 67602 36.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B240612

Connect the front door lock remote control cable assembly and front door inside locking cable assembly.


b.
B240574

Connect the connector.


c.
B240613

Attach the front door trim board sub-assembly to the 4 claws of the front door inner glass as shown in the illustration.


d.

Attach the 11 clips to install the front door trim board sub-assembly.


e.

Install the 3 screws.


f.

Attach the 4 claws to install the 2 door armrest caps.


Hide 69298A 37.INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH

a.

Attach the 3 claws to install the inside handle bezel.


Hide 67492A 38.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Attach the 2 clips to install the front door lower frame bracket garnish.


Hide 39.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 40.INITIALIZE POWER WINDOW CONTROL SYSTEM

a.

Initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).


Hide 41.CHECK SRS WARNING LIGHT