Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM
RM1440E _59 Vehicle Exterior _056170 WIPER / WASHER _0274189 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rear Washer does not Operate  


DESCRIPTION

The windshield wiper switch controls the rear washer motor and pump.

WIRING DIAGRAM

B241661E03
5.521,2.979 7.063,3.688 1.542,0.708 10 false Main Body ECU (Multiplex Network Body ECU) 5.615,0.677 6.417,1.063 0.802,0.385 10 false RWSW 4.24,0.479 4.552,0.729 0.313,0.25 10 false 5 4.167,0.677 4.573,1.01 0.406,0.333 10 false F21 2.813,0.677 3.344,1.063 0.531,0.385 10 false F20 2.885,0.479 3.177,0.75 0.292,0.271 10 false 2 3.156,0.677 3.49,0.906 0.333,0.229 10 false EW 3.813,0.677 4.271,1.031 0.458,0.354 10 false WR 2.51,1.094 4.823,1.281 2.313,0.188 10 false Windshield Wiper Switch Assembly 5.25,0.677 5.74,1.104 0.49,0.427 10 false F10 5.292,2.302 5.698,2.667 0.406,0.365 10 false F8 5.625,2.302 6.125,2.698 0.5,0.396 10 false BW 5.333,0.479 5.667,0.771 0.333,0.292 10 false 8 5.313,2.094 5.552,2.396 0.24,0.302 10 false 2 2.646,4.969 4.781,5.719 2.135,0.75 10 false Rear Washer Motor and Pump Assembly 3.979,3.531 5.208,3.896 1.229,0.365 10 false WASHER RR 2.646,2.406 3.75,2.75 1.104,0.344 10 false ECU-IG NO. 2 2.781,3.198 3.833,3.667 1.052,0.469 10 false WASHER 0.208,2.292 1.177,2.729 0.969,0.438 10 false from Battery 4.813,2.177 5.052,2.448 0.24,0.271 10 false 1 3.927,2.198 4.198,2.479 0.271,0.281 10 false 2 3.938,2.927 4.302,3.198 0.365,0.271 10 false 5 4.823,2.917 5.104,3.219 0.281,0.302 10 false 3 3.823,4.219 4.271,4.563 0.448,0.344 10 false 1 3.281,4.219 3.552,4.469 0.271,0.25 10 false 2 4.427,4.219 4.917,4.573 0.49,0.354 10 false 5 2.677,4.219 3.042,4.49 0.365,0.271 10 false 4 2.646,4.771 3.104,4.969 0.458,0.198 10 false A27

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (WINDSHIELD WIPER SWITCH)
a.

Use the Data List to check if the rear washer is functioning properly (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Rear Washer SW Signal Rear washer switch / ON or OFF ON: Rear washer switch on
OFF: Rear washer switch off
-

OK:

On the intelligent tester screen, item changes between ON and OFF according to the above chart.



OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WASHER RR RELAY)

NG

9.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WASHER RR RELAY)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Rear Wiper Washer Motor Relay WASHER RR relay operation ON/OFF -

OK:

The rear washer motor operates normally.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT WASHER RR RELAY
3.INSPECT WASHER RR RELAY
a.
B242124E01
1.292,0.74 1.584,0.185 1.584,0.185 1.773,0.185 false 0.708,0.74 1,0.185 1,0.185 1.189,0.185 false 1.789,0.082 1.924,0.258 0.135,0.177 10 2 1.651,1.353 1.763,1.500 0.112,0.147 10 5 1.222,0.082 1.357,0.258 0.135,0.177 10 1 0.98,1.159 1.533,1.457 1.533,1.457 1.621,1.457 false 1.651,1.835 1.763,1.981 0.112,0.147 10 3 0.98,1.64 1.533,1.938 1.533,1.938 1.621,1.938 false

Remove the WASHER RR relay from the engine room relay block, junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - WASHER RR RELAY)

NG

REPLACE WASHER RR RELAY

4.CHECK HARNESS AND CONNECTOR (BATTERY - WASHER RR RELAY)
a.
B242123E01
0.349,0.148 0.526,0.311 0.177,0.163 10 *a

Remove the WASHER RR relay from the engine room relay block, junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
RR WASHER relay terminal 2 - Body ground Ignition switch ON 11 to 14 V
RR WASHER relay terminal 2 - Body ground Ignition switch off Below 1 V
RR WASHER relay terminal 5 - Body ground Ignition switch ON 11 to 14 V
RR WASHER relay terminal 5 - Body ground Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to WASHER RR Relay)



OK

5.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - MAIN BODY ECU)
a.

Remove the WASHER RR relay from the engine room relay block, junction block.


b.

Disconnect the F8 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F8-2 (BW) - WASHER RR relay terminal 1 Always Below 1 Ω
F8-2 (BW) - Body ground Always 10 kΩ or higher




OK

6.INSPECT REAR WASHER MOTOR AND PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR WASHER MOTOR AND PUMP ASSEMBLY
a.
E140350

Remove the rear washer motor and pump (See page Vehicle Exterior>WIPER / WASHER>WASHER MOTOR(for Rear Side)>REMOVAL).


b.

Apply battery voltage to the rear wiper motor and check the operation of the rear wiper motor.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1
Battery negative (-) → 2
Rear washer motor operation is normal




OK

7.CHECK WIRE HARNESS (REAR WASHER MOTOR AND PUMP ASSEMBLY)

NG

REPLACE REAR WASHER MOTOR AND PUMP ASSEMBLY

7.CHECK WIRE HARNESS (REAR WASHER MOTOR AND PUMP ASSEMBLY)
a.

Disconnect the A27 level warning switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-5 - 1 Always Below 1 Ω
A27-4 - 2 Always Below 1 Ω
A27-5 - Body ground Always 10 kΩ or higher
A27-4 - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (REAR WASHER MOTOR AND PUMP ASSEMBLY - WASHER RR RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (REAR WASHER MOTOR AND PUMP ASSEMBLY - WASHER RR RELAY AND BODY GROUND)
a.

Disconnect the A27 rear washer motor connector.


b.

Remove the WASHER RR relay from the engine room relay block, junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-5 - WASHER RR relay terminal 3 Always Below 1 Ω
A27-4 - Body ground Always Below 1 Ω
A27-5 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
a.
U149791E02
2.26,1.052 2.781,1.792 2.781,1.792 2.958,1.792 false 1.615,1.271 1.802,1.771 1.802,1.771 1.979,1.771 false 1.271,0.333 1.385,0.479 0.115,0.146 10 false B 2.25,0.323 2.365,0.469 0.115,0.146 10 false A 2.99,1.719 3.24,1.865 0.25,0.146 10 false EW 2.01,1.708 2.26,1.854 0.25,0.146 10 false WR

Remove the windshield wiper switch (See page Vehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
B-5 (WR) - A-2 (EW) Rear washer switch on Below 1 Ω
B-5 (WR) - A-2 (EW) Rear washer switch off 10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the F20 and F21 windshield wiper switch connectors.


b.

Disconnect the F10 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-5 (WR) - F10-8 (RWSW) Always Below 1 Ω
F20-2 (EW) - Body ground Always Below 1 Ω
F21-5 (WR) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR