Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM1440E _59 Vehicle Exterior _056171 LIGHTING (EXT) _0274213 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU. The main body ECU turns on or off the headlights and taillights according to the signal.

DTC Code DTC Detection Condition Trouble Area
B1244
·

Malfunction in automatic light control sensor.

·

Open or short in automatic light control sensor circuit.


·

Automatic light control sensor

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

E188439E02
0.236,2.731 0.473,2.904 0.237,0.173 10 G2 0.236,2.875 2.253,3.086 2.017,0.211 10 Automatic Light Control Sensor 5.339,2.711 5.668,2.884 0.329,0.173 10 F9 5.339,2.855 7.023,3.222 1.684,0.367 10 Main Body ECU (Multiplex Network Body ECU) 1.104,0.602 1.510,0.804 0.406,0.202 10 CLTB 1.104,1.387 1.510,1.589 0.406,0.202 10 CLTS 1.104,2.19 1.510,2.392 0.406,0.202 10 CLTE 5.727,0.602 6.133,0.804 0.406,0.202 10 CLTB 5.727,1.387 6.133,1.589 0.406,0.202 10 CLTS 5.727,2.19 6.133,2.392 0.406,0.202 10 CLTE 5.376,0.502 5.563,0.668 0.187,0.166 10 20 5.376,1.3 5.563,1.466 0.187,0.166 10 21 5.376,2.099 5.563,2.266 0.187,0.166 10 22 1.63,0.502 1.817,0.668 0.187,0.166 10 6 1.63,1.3 1.817,1.466 0.187,0.166 10 5 1.63,2.099 1.817,2.266 0.187,0.166 10 3

PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1244 output does not occur.




OK

NG

2.READ VALUE USING INTELLIGENT TESTER (AUTOMATIC LIGHT CONTROL SENSOR)
2.READ VALUE USING INTELLIGENT TESTER (AUTOMATIC LIGHT CONTROL SENSOR)
a.

Using the intelligent tester, read the Data List (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate information / 0 ms. to 99.99 ms. Value is output according to ambient light levels -

OK:

Normal condition listed above is displayed.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the F9 main body ECU connector.


b.

Disconnect the G2 automatic light control sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-22 (CLTE) - G2-3 (CLTE) Always Below 1 Ω
F9-21 (CLTS) - G2-5 (CLTS) Always Below 1 Ω
F9-20 (CLTB) - G2-6 (CLTB) Always Below 1 Ω
F9-22 (CLTE) - Body ground Always 10 kΩ or higher
F9-21 (CLTS) - Body ground Always 10 kΩ or higher
F9-20 (CLTB) - Body ground Always 10 kΩ or higher




OK

4.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
U150531E02
2.031,1.125 1.25,1.885 false 2.323,1.125 2.323,1.823 false 0.094,0.01 0.281,0.198 0.188,0.188 10 false *a 0.979,1.896 1.354,2.073 0.375,0.177 10 false CLTE 2.135,1.854 2.51,2.031 0.375,0.177 10 false CLTB 0.25,0.521 0.521,0.688 0.271,0.167 10 false F9

Reconnect the F9 main body ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F9-20 (CLTB) - F9-22 (CLTE) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V


Text in Illustration
*a Component with harness connected
(Main Body ECU)



OK

5.CHECK AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.CHECK AUTOMATIC LIGHT CONTROL SENSOR
a.
U150532E01
0.054,0.027 0.257,0.183 0.202,0.156 10 *a 2.561,1.784 2.951,1.928 0.390,0.144 10 CLTS 2.569,1.157 2.955,1.301 0.385,0.144 10 CLTE 2.532,1.228 1.835,1.228 false 1.842,1.367 2.527,1.859 false 0.331,0.47 0.542,0.651 0.211,0.181 10 G2

Reconnect the G2 automatic light control sensor connector.


b.

Connect an oscilloscope to the automatic light control sensor connector.


c.
B113714E01
2.948,1.063 3.292,1.219 0.344,0.156 10 GND 1.844,1.177 1.969,1.333 0.125,0.156 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Switch Condition Specified Condition
G2-3 (CLTE) - G2-5 (CLTS) 5 V/DIV., 5 ms./DIV. Ignition switch ON, headlight dimmer switch in AUTO position Correct waveform is as shown


Text in Illustration
*a Component with harness connected
(Automatic Light Control Sensor)

HINT:

If the ambient light becomes brighter, width A becomes narrower.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR