Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM
RM1440E _59 Vehicle Exterior _056171 LIGHTING (EXT) _0274213 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Headlight Relay Circuit  


DESCRIPTION

The main body ECU receives headlight dimmer switch information signals, and illuminates the low beam headlight.

WIRING DIAGRAM

E199761E01
4.987,2.608 5.143,2.764 0.156,0.156 10 A 4.987,2.765 6.720,3.132 1.732,0.367 10 Main Body ECU (Multiplex Network Body ECU) 4.991,0.891 5.202,1.061 0.211,0.170 10 15 5.313,0.986 5.733,1.156 0.420,0.170 10 HRLY 2.826,1.582 3.417,1.752 0.591,0.170 10 H-LP LO 3.465,0.897 3.621,1.062 0.156,0.165 10 2 2.666,0.897 2.822,1.062 0.156,0.165 10 1 3.465,1.223 3.621,1.389 0.156,0.165 10 3 2.666,1.223 2.822,1.389 0.156,0.165 10 5 0.587,0.962 1.455,1.164 0.869,0.202 10 from Battery 0.307,1.976 1.889,2.160 1.582,0.184 10 to Low Beam Headlights

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (HEADLIGHT RELAY)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Headlight Relay Low beam headlight relay ON/OFF -

OK:

Headlight relay operates (low beam headlights illuminate).




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HEADLIGHT RELAY (H-LP LO)
2.INSPECT HEADLIGHT RELAY (H-LP LO)
a.
E108359E04
2.317,0.788 2.747,0.547 false 2.323,1.418 2.237,1.71 false 2.083,1.166 1.928,1.475 false 2.541,1.074 2.781,1.246 false 1.586,0.705 1.714,0.906 0.128,0.201 10 3 1.588,1.258 1.711,1.459 0.123,0.201 10 2 2.777,0.421 2.905,0.622 0.128,0.201 10 3 2.803,1.137 2.926,1.338 0.123,0.201 10 1 2.168,1.699 2.302,1.900 0.134,0.201 10 5 1.819,1.441 1.947,1.642 0.128,0.201 10 2 0.498,1.258 0.627,1.459 0.128,0.201 10 1 0.496,0.705 0.629,0.906 0.134,0.201 10 5

Remove the headlight relay from the engine room relay block, junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
Battery voltage applied between terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT RELAY [H-LP LO])

NG

REPLACE HEADLIGHT RELAY

3.CHECK HARNESS AND CONNECTOR (BATTERY - HEADLIGHT RELAY [H-LP LO])
a.
E199762E01
0.375,0.153 0.586,0.323 0.211,0.170 10 *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Headlight relay terminal 1 - Body ground Always 11 to 14 V
Headlight relay terminal 5 - Body ground


Text in Illustration
*a Front view of wire harness connector
(to Headlight Relay)



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT RELAY [H-LP LO] - MAIN BODY ECU)
a.

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Headlight relay terminal 2 - A-15 (HRLY) Always Below 1 Ω
A-15 (HRLY) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR