Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2016.12
RM1440E _57 Power Source / Network _056154 NETWORKING _0274052 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B1273  Sliding Roof ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B1273 No communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Sliding roof ECU (sliding roof drive gear sub-assembly)

·

Driver side junction block assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

B467032E02
3.313,2.083 4.271,2.375 0.958,0.292 10 false from Battery 2.792,2.583 4.25,2.917 1.458,0.333 10 false from IG1 NO. 1 Relay 4.542,2.26 5.198,2.521 0.656,0.26 10 false S/ROOF 4.375,2.76 5.354,3.042 0.979,0.281 10 false ECU-IG NO. 2 5.406,2.104 5.667,2.365 0.26,0.26 10 false B 5.406,2.594 5.667,2.854 0.26,0.26 10 false IG 5.417,3.104 5.646,3.344 0.229,0.24 10 false E 4.917,3.604 5.323,3.865 0.406,0.26 10 false S10 4.917,3.792 6.844,4.417 1.927,0.625 10 false Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly) 5.417,0.75 5.927,1.01 0.51,0.26 10 false MPX1 0.552,2.333 2.208,2.917 1.656,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 0.573,2.146 0.833,2.406 0.26,0.26 10 false A 0.698,4.323 2.479,4.646 1.781,0.323 10 false : LIN Communication Line 1.458,0.729 1.885,0.969 0.427,0.24 10 false LIN2 1.844,0.583 2.115,0.823 0.271,0.24 10 false 16 5.125,0.583 5.396,0.823 0.271,0.24 10 false 11 5.208,1.979 5.479,2.219 0.271,0.24 10 false 8 5.208,2.469 5.479,2.708 0.271,0.24 10 false 1 5.167,2.979 5.438,3.219 0.271,0.24 10 false 12 2.021,1.188 2.344,1.427 0.323,0.24 10 false 2B 3.479,0.583 3.75,0.823 0.271,0.24 10 false 11 2.021,1.365 3.25,1.948 1.229,0.583 10 false Driver Side Junction Block Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1273 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Connect the 2B driver side junction block assembly connector.


c.

Disconnect the S10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - S10-11 (MPX1) Always Below 1 Ω
A-16 (LIN2) or S10-11 (MPX1) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - BATTERY AND BODY GROUND)

NG

8.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - BATTERY AND BODY GROUND)
a.
U155876E02
1.229,1.146 0.969,0.781 0.969,0.781 0.802,0.781 true 1.229,1.417 0.979,1.74 0.979,1.74 0.813,1.74 true 2.198,1.406 2.427,1.74 2.427,1.74 2.594,1.74 true 0.094,0.094 0.385,0.406 0.292,0.313 10 false *a 1.594,0.333 1.938,0.573 0.344,0.24 10 false S10 2.677,1.677 2.917,1.938 0.24,0.26 10 false E 0.656,1.656 0.917,1.906 0.26,0.25 10 false B 0.604,0.698 0.896,0.979 0.292,0.281 10 false IG

Disconnect the S10 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S10-12 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
S10-8 (B) - Body ground Always 11 to 14 V
S10-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))


OK

5.REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
a.

Temporarily replace the sliding roof ECU (sliding roof drive gear sub-assembly) with a new or normally functioning one (See page Vehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING>DISASSEMBLY).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1273 is not output.




OK

END (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

8.CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See pagePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - 2B-11 Always Below 1 Ω
A-16 (LIN2) or 2B-11 - Body ground Always 10 kΩ or higher




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY))

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY