Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0327    Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0328    Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

DTC    P0332    Knock Sensor 2 Circuit Low Input (Bank 2)

DTC    P0333    Knock Sensor 2 Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

Flat-type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 6 kHz and 15 kHz.
2 knock sensors are fitted onto the engine block to detect engine knocking.
Each knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.

DTC No.
DTC Detection Condition
Trouble Area
P0327
P0332
Output voltage of the knock sensor is below 0.5 V (1 trip detection logic).
  1. Short in knock sensor circuit
  2. Knock sensor
  3. ECM
P0328
P0333
Output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic).
  1. Open in knock sensor circuit
  2. Knock sensor
  3. ECM

HINT:
When DTC P0327, P0328, P0332 or P0333 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

Reference: Inspection using an oscilloscope
A085286E27
The correct waveform is as shown.
Item
Content
Terminal
KNK1 - EKNK
KNK2 - EKN2
Equipment Setting
1 V/DIV.
1 msec./DIV.
Condition
Engine speed at 4000 rpm with warm engine

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains low or high for more than 1 second, the ECM interprets this as a malfunction in the sensor circuit and stores a DTC.
The monitor for DTCs P0327, P0328, P0332 and P0333 begins to run 5 seconds after the engine is started.
If the malfunction is not repaired successfully, DTC P0327, P0328, P0332 or P0333 is stored 5 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0327: Knock sensor (bank 1) range check (Low voltage)
P0328: Knock sensor (bank 1) range check (High voltage)
P0332: Knock sensor (bank 2) range check (Low voltage)
P0333: Knock sensor (bank 2) range check (High voltage)
Required Sensors/Components (Main)
Knock sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
1 second
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None
Battery voltage
10.5 V or higher
Time after engine start
5 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


Knock Sensor Range Check (Low voltage) P0327 and P0332 
Knock sensor voltage
Below 0.5 V

Knock Sensor Range Check (High voltage) P0328 and P0333 
Knock sensor voltage
Higher than 4.5 V

CONFIRMATION DRIVING PATTERN


A199234E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and wait 10 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0327, P0328, P0332 or P0333.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again [C].

  12. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A227107E01


INSPECTION PROCEDURE

HINT:
  1. DTCs P0327 and P0328 are for the bank 1 knock sensor circuit.
  2. DTCs P0332 and P0333 are for the bank 2 knock sensor circuit.
  3. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK KNOCK SENSOR
C214336E14
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B37-11 (KNK1) - B37-12 (EKNK)
    20°C (68°F)
    120 to 280 kΩ
    B37-5 (KNK2) - B37-6 (EKN2)
    20°C (68°F)
    120 to 280 kΩ

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
Go to step 3
OK


2.CHECK TERMINAL VOLTAGE (ECM)
A225616E01
  1. Disconnect the Be1 connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B37-11 (KNK1) - B37-12 (EKNK)
    Ignition switch ON
    4.5 to 5.5 V
    B37-5 (KNK2) - B37-6 (EKN2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
REPLACE ECM (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
  1. Disconnect the knock sensor connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
e2-2 - B37-11 (KNK1)
Always
Below 1 Ω
e2-1 - B37-12 (EKNK)
Always
Below 1 Ω
e1-2 - B37-5 (KNK2)
Always
Below 1 Ω
e1-1 - B37-6 (EKN2)
Always
Below 1 Ω
e2-2 or B37-11 (KNK1) - Body ground
Always
10 kΩ or higher
e2-1 or B37-12 (EKNK) - Body ground
Always
10 kΩ or higher
e1-2 or B37-5 (KNK2) - Body ground
Always
10 kΩ or higher
e1-1 or B37-6 (EKN2) - Body ground
Always
10 kΩ or higher

  1. Reconnect the knock sensor connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE KNOCK SENSOR (Click here)