Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0136    Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2)

DTC    P0137    Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2)

DTC    P0138    Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2)

DTC    P0139    Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2)

DTC    P013A    Oxygen Sensor Slow Response - Rich to Lean Bank 1 Sensor 2

DTC    P013C    Oxygen Sensor Slow Response - Rich to Lean Bank 2 Sensor 2

DTC    P0156    Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2)

DTC    P0157    Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2)

DTC    P0158    Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2)

DTC    P0159    Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2)

for Preparation Click here


DESCRIPTION

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air-fuel ratio must be precisely controlled so that it is always close to the stoichiometric air-fuel level. For the purpose of helping the ECM to deliver accurate air-fuel ratio control, a heated oxygen sensor is used.
The heated oxygen sensor is located behind the three-way catalytic converter, and detects the oxygen concentration in the exhaust gas. Since the sensor is integrated with a heater that heats the sensing portion, it is possible to detect the oxygen concentration even when the intake air volume is low (the exhaust gas temperature is low).
When the air-fuel ratio becomes lean, the oxygen concentration in the exhaust gas is rich. The heated oxygen sensor informs the ECM that the post-TWC air-fuel ratio is lean (low voltage, i.e. below 0.45 V).
Conversely, when the air-fuel ratio is richer than the stoichiometric air-fuel level, the oxygen concentration in the exhaust gas becomes lean. The heated oxygen sensor informs the ECM that the post-three-way catalytic converter air-fuel ratio is rich (high voltage, i.e. higher than 0.45 V). The heated oxygen sensor has the property of changing its output voltage drastically when the air-fuel ratio is close to the stoichiometric level.
The ECM uses the supplementary information from the heated oxygen sensor to determine whether the air-fuel ratio after the three-way catalytic converter is rich or lean, and adjusts the fuel injection time accordingly. Thus, if the heated oxygen sensor is working improperly due to internal malfunctions, the ECM is unable to compensate for deviations in the primary air-fuel ratio control.

A115539E07


DTC No.
DTC Detection Condition
Trouble Area
P0136
P0156
  1. Abnormal voltage output:
    1. During active air fuel ratio control, heated oxygen sensor voltage does not increase to 0.66 V or higher for certain period of time (2 trip detection logic)
  2. Low impedance:
    1. Sensor impedance less than 5 Ω for more than 30 seconds when ECM presumes sensor is warmed up and operating normally (2 trip detection logic)
  1. Heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Air fuel ratio sensor (sensor 1)
  4. Gas leak from exhaust system
  5. Fuel pressure
  6. Fuel injector assembly
  7. PCV valve and hose
  8. Intake system
P0137
P0157
  1. Low voltage (open):
    1. During active air fuel ratio control, following conditions (a) and (b) met for certain period of time (2 trip detection logic)
    2. (a) Heated Oxygen (HO2) sensor voltage output less than 0.21 V
    3. (b) Target air fuel ratio rich
  1. High impedance:
    1. Sensor impedance 15 kΩ or more for more than 90 seconds when ECM presumes sensor to be warmed up and operating normally (2 trip detection logic)
  1. Heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Air fuel ratio sensor (sensor 1)
  4. Gas leak from exhaust system
P0138
P0158
  1. Extremely high voltage (short):
    1. HO2 sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
  1. Heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Air fuel ratio sensor (sensor 1)
  4. ECM
P0139
P0159
Heated oxygen sensor (sensor 2) voltage does not drop to below 0.2 V immediately after fuel cut starts (2 trip detection logic)
  1. Heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Gas leak from exhaust system
P013A
P013C
Heated oxygen sensor (sensor 2) voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection logic)
  1. Heated oxygen sensor (sensor 2) circuit
  2. Heated oxygen sensor (sensor 2)
  3. Gas leak from exhaust system

MONITOR DESCRIPTION


Active Air Fuel Ratio Control
The ECM usually performs air fuel ratio feedback control so that the Air Fuel Ratio (A/F) sensor output indicates a near stoichiometric air fuel level. This vehicle includes active air fuel ratio control in addition to regular air fuel ratio control. The ECM performs active air fuel ratio control to detect any deterioration in the Three-Way Catalytic Converter (TWC) and Heated Oxygen (HO2) sensor malfunctions (refer to the diagram below).
Active air fuel ratio control is performed for approximately 15 to 20 seconds while driving with a warm engine. During active air fuel ratio control, the air fuel ratio is forcibly regulated to become lean or rich by the ECM. If the ECM detects a malfunction, a DTC is stored.

Abnormal Voltage Output of Heated Oxygen (HO2) Sensor (DTC P0136 and P0156)
While the ECM is performing active air fuel ratio control, the air fuel ratio is forcibly regulated to become rich or lean. If the sensor is not functioning properly, the voltage output variation is small. For example, when the heated oxygen sensor voltage does not increase to 0.66 V or higher during active air fuel ratio control, the ECM determines that the sensor voltage output is abnormal and stores DTC P0136 or P0156.

A152942E56


Open in Heated Oxygen (HO2) Sensor Circuit (DTC P0137 and P0157)
During active air fuel ratio control, the ECM calculates the Oxygen Storage Capacity (OSC)* of the Three-Way Catalytic Converter (TWC) by forcibly regulating the air fuel ratio to become rich or lean.
If the HO2 sensor has an open, or the voltage output of the sensor noticeably decreases, the OSC indicates an extraordinarily high value. Even if the ECM attempts to continue regulating the air fuel ratio to become rich or lean, the HO2 sensor output does not change.
While performing active air fuel ratio control, when the target air fuel ratio is rich and the HO2 sensor voltage output is 0.21 V or less (lean), the ECM interprets this as an abnormally low sensor output voltage and stores DTC P0137 or P0157.

HINT:
*: The TWC has the capability to store oxygen. The OSC and the emission purification capacity of the TWC are mutually related. The ECM determines whether the catalyst has deteriorated, based on the calculated OSC value .


A234468E30


High or Low Impedance of Heated Oxygen (HO2) Sensor (DTCs P0136 and P0156 or P0137 and P0157)
During normal air fuel ratio feedback control, there are small variations in the exhaust gas oxygen concentration. In order to continuously monitor the slight variation of the HO2 sensor signal while the engine is running, the impedance* of the sensor is measured by the ECM. The ECM determines that there is a malfunction in the sensor when the measured impedance deviates from the standard range.
*: The effective resistance in an alternating current electrical circuit.
A076841E30

HINT:
  1. The impedance cannot be measured using an ohmmeter.
  2. DTC P0136 or P0156 indicates the deterioration of the HO2 sensor. The ECM stores the DTC by calculating the impedance of the sensor when the typical enabling conditions are satisfied (2 driving cycles).
  3. DTC P0137 or P0157 indicates an open or short circuit in the HO2 sensor (2 driving cycles). The ECM stores the DTC when the impedance of the sensor exceeds the threshold 15 kΩ.


Extremely High Output Voltage of Heated Oxygen (HO2) Sensor (DTC P0138 and P0158)
The ECM continuously monitors the HO2 sensor output voltage while the engine is running.
DTC P0138 is stored if the HO2 sensor voltage output is more than 1.2 V for 10 seconds or more.

Abnormal Voltage Output of Heated Oxygen (HO2) Sensor During Fuel-cut (DTC P0139 and P0159)
The sensor output voltage drops to below 0.2 V (extremely lean status) immediately when the vehicle decelerates and fuel cut is operating. If the voltage does not drop to below 0.2 V for 7 seconds or more, the ECM determines that the sensor response has deteriorated, illuminates the MIL and stores a DTC.

Abnormal Voltage Output of Heated Oxygen Sensor during Fuel Cut from Rich Condition (DTC P013A and P013C)
If the sensor output voltage does not drop from 0.35 to 0.2 V immediately when the vehicle decelerates and fuel cut is operating, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY


All 
Related DTCs
P0136: Heated oxygen sensor (bank 1) output voltage (Abnormal voltage output)
P0136: Heated oxygen sensor (bank 1) impedance (Low)
P0137: Heated oxygen sensor (bank 1) output voltage (Low voltage)
P0137: Heated oxygen sensor (bank 1) impedance (High)
P0138: Heated oxygen sensor (bank 1) output voltage (High voltage)
P0138: Heated oxygen sensor (bank 1) output voltage (Extremely high)
P0139: Heated oxygen sensor (bank 1) output voltage during fuel cut
P013A: Heated oxygen sensor (bank 1) output voltage during fuel cut from rich condition
P013C: Heated oxygen sensor (bank 2) output voltage during fuel cut from rich condition
P0156: Heated oxygen sensor (bank 2) output voltage (Abnormal voltage output)
P0156: Heated oxygen sensor (bank 2) impedance (Low)
P0157: Heated oxygen sensor (bank 2) output voltage (Low voltage)
P0157: Heated oxygen sensor (bank 2) impedance (High)
P0158: Heated oxygen sensor (bank 2) output voltage (High voltage)
P0158: Heated oxygen sensor (bank 2) output voltage (Extremely high)
P0159: Heated oxygen sensor (bank 2) output voltage during fuel cut
Required Sensors/Components (Main)
Heated oxygen sensor
Required Sensors/Components (Related)
Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter and throttle position sensor
Frequency of Operation
Once per driving cycle: Active air-fuel ratio control detection / Heated oxygen sensor output voltage during fuel cut
Continuous: Other
Duration
20 seconds: Active air-fuel ratio control detection
90 seconds: Heated oxygen sensor impedance (High)
30 seconds: Heated oxygen sensor impedance (Low)
10 seconds: Output voltage (Stuck high)
7 seconds: Heated oxygen sensor voltage during fuel cut
MIL Operation
2 driving cycles: P0136, P0137, P0138, P0139, P0156, P0157, P0158 and P0159
1 driving cycle: P013A and P013C
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0031, P0032, P0051, P0052 (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058, P101D, P103D (Rear Oxygen Sensor Heater)
P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air Fuel Ratio Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0128 (Thermostat)
P0171, P0172, P0174, P0175 (Fuel System)
P0301 - P0306 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
P0451, P0452, P0453 (EVAP System)
P0500, P0722 (Vehicle Speed Sensor)
P0412, P1613 (Secondary Air Injection System Control)
P219A, P219B (Air-Fuel Ratio Imbalance)

Heated Oxygen Sensor Output Voltage (Abnormal Voltage Output, High Voltage and Low Voltage) 
Catalyst monitor precondition
Executing
Catalyst monitor precondition defined as when all of following conditions met:
-
Battery voltage
11 V or higher
Intake air temperature
-10°C (14°F) or higher
Engine coolant temperature
75°C (167°F) or higher
Atmospheric pressure
76 kPa-a (570 mmHg-a) or higher
Idling
OFF
Engine speed
Less than 3200 rpm
Air fuel ratio sensor status
Activated
Fuel system status
Closed loop
Fuel cut
OFF
Engine load
10 to 70%

Heated Oxygen Sensor Impedance (Low) 
DTC P0607
Not set
Battery voltage
11 V or higher
Estimated rear heated oxygen sensor temperature
Below 700°C (1292°F)
ECM monitor
Completed

Heated Oxygen Sensor Impedance (High) 
DTC P0607
Not set
Battery voltage
11 V or higher
Estimated rear heated oxygen sensor temperature
450 to 750°C (842 to 1382°F) or higher
ECM monitor
Completed

Heated Oxygen Sensor Output Voltage (Extremely High) 
Battery voltage
11 V or higher
Time after engine start
2 seconds or more

Heated Oxygen Sensor Output Voltage During Fuel Cut 
Engine coolant temperature
75°C (167°F) or higher
Estimated catalyst temperature
400°C (752°F) or higher
Fuel cut
ON

Heated Oxygen Sensor Response Rate during Fuel Cut from Rich Condition 
Battery voltage
11 V or higher
Engine coolant temperature
75°C (167°F) or higher
Estimated catalyst temperature
400°C (752°F) or higher
Fuel cut
ON

TYPICAL MALFUNCTION THRESHOLDS


Heated Oxygen Sensor Output Voltage (Abnormal Voltage Output) 
Either of following conditions met:
1 or 2
1. Conditions (a), (b) and (c) met
-
(a) Commanded air-fuel ratio
14.3 or less
(b) Rear heated oxygen sensor voltage
0.21 to 0.66 V
(c) OSC (Oxygen Storage Capacity of Catalyst)
1.8 g or more
2. Conditions (d), (e) and (f) met
-
(d) Commanded air-fuel ratio
14.9 or more
(e) Rear heated oxygen sensor voltage
0.21 to 0.66 V
(f) OSC
1.8 g or more

Heated Oxygen Sensor Output Voltage (Low) 
Conditions (a), (b) and (c) met
-
(a) Commanded air-fuel ratio
14.3 or less
(b) Rear heated oxygen sensor voltage
Below 0.21 V
(c) OSC
1.8 g or more

Heated Oxygen Sensor Output Voltage (High) 
Conditions (a), (b) and (c) met
-
(a) Commanded air-fuel ratio
14.9 or more
(b) Rear heated oxygen sensor voltage
Higher than 0.66 V
(c) OSC
1.8 g or more

Heated Oxygen Sensor Impedance (Low) 
Duration following condition met
30 seconds or more
Heated oxygen sensor impedance
Below 5 Ω

Heated Oxygen Sensor Impedance (High) 
Duration following condition met
90 seconds or more
Heated oxygen sensor impedance
15 kΩ or higher

Heated Oxygen Sensor Output Voltage (Extremely High) 
Duration following condition met
10 seconds or more
Heated oxygen sensor voltage
1.2 V or higher

Heated Oxygen Sensor Output Voltage during Fuel Cut 
Duration until rear heated oxygen sensor voltage drops to 0.2 V after fuel cut
7 seconds or more

Heated Oxygen Sensor Response Rate during Fuel Cut from Rich Condition 
Duration that heated oxygen sensor voltage drops from 0.35 to 0.2 V during fuel cut (Normalized)
0.5 second or more

COMPONENT OPERATING RANGE


Duration following condition met
30 seconds or higher
Heated oxygen sensor voltage
Varies between 0.1 and 0.9 V

CONFIRMATION DRIVING PATTERN

  1. P0136, P0137, P0138, P0156, P0157 and P0158

A199376E74

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
  7. With the transmission in 4th gear or higher, drive the vehicle at 60 to 120 km/h (40 to 75 mph) for 10 minutes or more [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0136, P0137, P0138, P0156, P0157 and P0158.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.

  1. P0139, P013A, P013C and P0159

A284467E04

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
  8. Check that Catalyst Efficiency / Current is Incomplete.
  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with the shift lever in P [A].

    HINT:
    In order to keep the idling stable, turn off the A/C and all other electric loads and do not perform any shift operations.

  10. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  11. Drive the vehicle at 60 km/h (37 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2, RL F/C B2S2 [D].
  13. Check the Test Value for RL F/C B1S2, RL F/C B2S2.

    HINT:
    If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 sensor monitor is not finished.

  14. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  15. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  16. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  17. Input the DTC: P0139, P013A, P013C or P159.
  18. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows NORMAL, the system is normal.
    3. If the judgment result shows INCOMPLETE or N/A, drive the vehicle with the shift lever in S, and then perform step [C] again.

  19. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM


A293114E01


INSPECTION PROCEDURE

HINT:
Sensor 2 refers to the sensor mounted between the front and rear catalysts.

HINT:
Techstream only:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the air fuel ratio sensor, heated oxygen sensor and other potential trouble areas are malfunctioning.

  1. The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the Techstream.
    1. Connect the Techstream to the DLC3.
    2. Start the engine and turn the Techstream on.
    3. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    5. Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
    6. Monitor the voltage outputs of the air fuel and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2, or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

HINT:
  1. Change the fuel injection volume within the range of -12.5% to 12.5%. The injection volume can be changed in fine gradations.
  2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Standard:

Tester Display
(Sensor)
Injection Volume
Status
Voltage
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
12.5%
Rich
Below 3.1 V
AFS Voltage B1S1 or AFS Voltage B2S1
(A/F)
-12.5%
Lean
Higher than 3.4 V
O2S B1S2 or O2S B2S2
(HO2)
12.5%
Rich
Higher than 0.55 V
O2S B1S2 or O2S B2S2
(HO2)
-12.5%
Lean
Below 0.4 V

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.


Case
Air Fuel Ratio Sensor (Sensor 1) Output Voltage
Heated Oxygen Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E11
A151324E08
A150787E11
A150788E06
-
2
A150787E11
A150790E01
A150787E11
A150788E06
  1. Air fuel ratio sensor
  2. Air fuel ratio sensor heater
  3. Air fuel ratio sensor circuit
3
A150787E11
A151324E08
A150787E11
A150790E01
  1. Heated oxygen sensor
  2. Heated oxygen sensor heater
  3. Heated oxygen sensor circuit
4
A150787E11
A150790E01
A150787E11
A150790E01
  1. Fuel injector assembly
  2. Fuel pressure
  3. Gas leak from exhaust system (air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the air fuel and heated oxygen sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor / AFS Voltage B1S1 or AFS Voltage B2S1, and O2S B1S2 or O2S B2S2. Then press the graph button on the Data List display.

HINT:
  1. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0138 will be stored.
  3. If the OX2B wire from the ECM connector is short-circuited to the +B wire, DTC P0158 will be stored.

1.READ DTC OUTPUT
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P0138 or P0158
    A
    P0137 or P0157
    B
    P0136 or P0156
    C
    P0139, P013A, P013C or P0159
    D
    P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output
    E



B
Go to step 9

C
Go to step 7

D
Go to step 18

E
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2 or O2S B2S2.

  1. Allow the engine to idle.

  1. Read the heated oxygen sensor output voltage while idling.

    Result 
    Tester Display
    Proceed to
    1 V or higher
    A
    Below 1 V
    B



B
Go to step 5
A


3.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)


    A224879E01
  1. Disconnect the heated oxygen sensor connector (bank 1 sensor 2) or oxygen sensor connector (bank 2 sensor 2).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Bank 1 Sensor 2):
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 3 (OX1B)
    Always
    10 kΩ or higher

    Standard Resistance (Bank 2 Sensor 2):
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 3 (OX2B)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (to Heated Oxygen Sensor Bank 1)
    *b
    Component without harness connected
    (to Heated Oxygen Sensor Bank 2)

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
  1. Turn the ignition switch off and wait for 5 minutes.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B39-12 (HT1B) - B36-2 (OX1B)
    Always
    10 kΩ or higher
    B39-13 (HT2B) - B36-4 (OX2B)
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

5.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the Techstream and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the Techstream.

HINT:
  1. Change the fuel injection volume within the range of -12.5% to 12.5%. The injection volume can be changed in 1% gradations within this range.
  2. The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the Techstream.
  3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Result 
Tester Display (Sensor)
Voltage Variation
Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
Alternates between higher than and below 3.3 V
OK
Remains at higher than 3.3 V
NG
Remains at below 3.3 V
NG

HINT:
A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either below or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E52



NG
Go to step 15
OK


6.INSPECT AIR FUEL RATIO SENSOR

HINT:
This air fuel ratio sensor test is to check the air fuel ratio sensor current during the fuel-cut. When the sensor is normal, the sensor current will be below 3 mA in this test.

  1. Clear DTCs (Click here).



  1. Drive the vehicle according to the drive pattern listed below.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    1. Warm up the engine.

    2. Drive the vehicle at 60 km/h (40 mph) or more for 10 minutes or more.

    3. Stop the vehicle.



    4. Accelerate the vehicle to 60 km/h (40 mph) or more and decelerate for 5 seconds or more. Perform this 3 times.


      A166560E06

  1. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / Details.

  1. Confirm that RANGE B1S1 and RANGE B2S1 are either PASS or FAIL. If the Techstream shows incomplete, recheck RANGE B1S1 and RANGE B2S1 after performing the drive pattern again.

    HINT:
    If the Techstream shows incomplete again, increase the vehicle speed and use second gear to decelerate the vehicle.

  1. Select RANGE B1S1 and press ENTER.

  1. Read the test value.

    Standard current:
    Below 3.0 mA

    NOTICE:
    Do not turn the ignition switch off during this step because the test results will be lost.



OK
Go to step 12

NG
Go to step 15

7.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / O2S B1S2 or O2S B2S2.

  1. Change the fuel injection volume using the Techstream, monitoring the voltage output of the heated oxygen sensors displayed on the Techstream.

    HINT:
    1. Change the fuel injection volume within the range of -12.5% to 12.5%. The injection volume can be changed in 1% gradations within this range.
    2. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

    Standard voltage:
    Fluctuates between 0.4 V or less and 0.5 V or higher.



NG
Go to step 9
OK


8.PERFORM ACTIVE TEST USING TECHSTREAM (INJECTION VOLUME)
  1. Connect the Techstream to the DLC3.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

  1. Change the fuel injection volume using the Techstream and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the Techstream.

HINT:
  1. Change the fuel injection volume within the range of -12.5% to 12.5%. The injection volume can be changed in 1% gradations within this range.
  2. The air fuel ratio sensor is displayed as AFS Voltage B1S1 or AFS Voltage B2S1, and the heated oxygen sensor is displayed as O2S B1S2 or O2S B2S2 on the Techstream.
  3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.


Result 
Tester Display (Sensor)
Voltage Variation
Proceed to
AFS Voltage B1S1
AFS Voltage B2S1
Alternates between higher than and below 3.3 V
OK
Remains at higher than 3.3 V
NG
Remains at below 3.3 V
NG

HINT:
A normal heated oxygen sensor voltage (O2S B1S2 or O2S B2S2) reacts in accordance with increases and decreases in fuel injection volumes. When the air fuel ratio sensor voltage remains at either below or higher than 3.3 V despite the heated oxygen sensor indicating a normal reaction, the air fuel ratio sensor is malfunctioning.


A121606E52



NG
Go to step 15
OK

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO AND REPAIR CAUSE (FUEL INJECTOR, FUEL PRESSURE, EXHAUST GAS LEAKAGE, ETC.) 

9.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leakage from the exhaust manifold and pipe.

    OK:
    No exhaust gas leakage.



NG
REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT
OK


10.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor .



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor connector (bank 1 sensor 2) or heated oxygen sensor connector (bank 2 sensor 2).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    B29-1 (HT1B) - B39-12 (HT1B)
    Always
    Below 1 Ω
    B29-3 (OX1B) - B36-2 (OX1B)
    Always
    Below 1 Ω
    B29-4 (E2) - B36-1 (EX1B)
    Always
    Below 1 Ω
    B30-1 (HT2B) - B39-13 (HT2B)
    Always
    Below 1 Ω
    B30-3 (OX2B) - B36-4 (OX2B)
    Always
    Below 1 Ω
    B30-4 (E2) - B36-3 (EX2B)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    B29-1 (HT1B) or B39-12 (HT1B) - Body ground
    Always
    10 kΩ or higher
    B29-3 (OX1B) or B36-2 (OX1B) - Body ground
    Always
    10 kΩ or higher
    B29-4 (E2) or B36-1 (EX1B) - Body ground
    Always
    10 kΩ or higher
    B30-1 (HT2B) or B39-13 (HT2B) - Body ground
    Always
    10 kΩ or higher
    B30-3 (OX2B) or B36-4 (OX2B) - Body ground
    Always
    10 kΩ or higher
    B30-4 (E2) or B36-3 (EX2B) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the heated oxygen sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).


NEXT


13.PERFORM CONFIRMATION DRIVING PATTERN
  1. Perform Confirmation Driving Pattern (P0136, P0137, P0138, P0156, P0157 and P0158).


NEXT


14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158 IS OUTPUT AGAIN)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0136, P0137, P0138, P0156, P0157 and P0158.
    Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern, increasing the vehicle speed and using second gear to decelerate the vehicle.
    Result 
    Display (DTC Output)
    Proceed to
    ABNORMAL
    (P0136, P0137, P0138, P0156, P0157 or P0158 detected)
    A
    NORMAL
    (No DTC output)
    B



B
END
A

REPLACE AIR FUEL RATIO SENSOR (Click here)  

15.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


16.PERFORM CONFIRMATION DRIVING PATTERN
  1. Perform Confirmation Driving Pattern (P0136, P0137, P0138, P0156, P0157 and P0158).


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158 IS OUTPUT AGAIN)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0136, P0137, P0138, P0156, P0157 and P0158.
    Check that DTC MONITOR is NORMAL. If DTC MONITOR is INCOMPLETE, perform the drive pattern, increasing the vehicle speed and using second gear to decelerate the vehicle.
    Result 
    Display (DTC Output)
    Proceed to
    ABNORMAL
    (P0136, P0137, P0138, P0156, P0157 or P0158 detected)
    A
    NORMAL
    (No DTC output)
    B



B
END
A

REPLACE HEATED OXYGEN SENSOR (Click here)  

18.READ VALUE USING TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / O2S B1S2 or O2S B2S2.

  1. After warming up the engine, run the engine at an engine speed of 2500 rpm for 3 minutes.

  1. Idle the engine.

  1. Depress the accelerator pedal quickly until the engine speed reaches 2500 rpm 3 times.
    Result 
    Result
    Proceed to
    Oxygen sensor output voltage higher than 1.0 V
    A
    Oxygen sensor output voltage below 1.0 V
    B



B
Go to step 21
A


19.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT)


    A224879E01
  1. Disconnect the heated oxygen sensor connector (bank 1 sensor 2) or heated oxygen sensor connector (bank 2 sensor 2).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Bank 1 Sensor 2):
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 3 (OX1B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E2)
    Always
    10 kΩ or higher

    Standard Resistance (Bank 2 Sensor 2):
    Tester Connection
    Condition
    Specified Condition
    2 (+B) - 3 (OX2B)
    Always
    10 kΩ or higher
    2 (+B) - 4 (E2)
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (to Heated Oxygen Sensor Bank 1)
    *b
    Component without harness connected
    (to Heated Oxygen Sensor Bank 2)

  1. Reconnect the heated oxygen sensor connector.



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


20.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
  1. Turn the ignition switch off and wait for 5 minutes.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B39-12 (HT1B) - B36-2 (OX1B)
    Always
    10 kΩ or higher
    B39-13 (HT2B) - B36-4 (OX2B)
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

21.PERFORM CONFIRMATION DRIVING PATTERN
  1. Perform Confirmation Driving Pattern (P0139 and P0159).


NEXT


22.CHECK WHETHER DTC OUTPUT RECURS (DTC P0139, P013A, P013C OR P0159 IS OUTPUT AGAIN)
  1. Read the DTCs (Click here).
    Result 
    Result
    Proceed to
    P0139, P013A, P013C or P0159 is output
    A
    No DTC is output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE HEATED OXYGEN SENSOR (Click here)