Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0102    Mass or Volume Air Flow Circuit Low Input

DTC    P0103    Mass or Volume Air Flow Circuit High Input

for Preparation Click here


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.
The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.
Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.
By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.
The circuit is constructed so that the platinum hot wire and temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:
When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM according to the engine speed and throttle valve position. The ECM continues operating in fail-safe mode until a pass condition is detected.


A202104E01


DTC No.
DTC Detection Condition
Trouble Area
P0102
Mass air flow meter voltage is below 0.2 V for 3 seconds
(1 trip detection logic: Engine speed is less than 4000 rpm)
(2 trip detection logic: Engine speed is 4000 rpm or more).
  1. Open or short in mass air flow meter circuit
  2. Mass air flow meter
  3. ECM
P0103
Mass air flow meter voltage is higher than 4.9 V for 3 seconds
(1 trip detection logic: Engine speed is less than 4000 rpm)
(2 trip detection logic: Engine speed is 4000 rpm or more).
  1. Open or short in mass air flow meter circuit
  2. Mass air flow meter
  3. ECM

HINT:
When any of these DTCs are stored, check the air-flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Air Flow Rate (g/sec.)
Malfunction
Approximately 0.0
  1. Open in mass air flow meter power source circuit
  2. Open or short in VG circuit
271.0 or more
  1. Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.
Example:
When the sensor output voltage remains below 0.2 V, or higher than 4.9 V, for more than 3 seconds, the ECM stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0102: Mass air flow meter range check (Low voltage)
P0103: Mass air flow meter range check (High voltage)
Required Sensors/Components (Main)
Mass air flow meter
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
3 seconds
MIL Operation
Immediate: Engine speed less than 4000 rpm
2 driving cycles: Engine speed 4000 rpm or more
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not present
None

TYPICAL MALFUNCTION THRESHOLDS


P0102 
Mass air flow meter voltage
Below 0.2 V

P0103 
Mass air flow meter voltage
Higher than 4.9 V

COMPONENT OPERATING RANGE


Mass air flow meter voltage
0.2 V to 4.9 V

CONFIRMATION DRIVING PATTERN


A228075E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. Idle the engine for 5 seconds [B].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Run the engine at an engine speed of 4000 rpm or more for 5 seconds [D].
  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].
  12. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  14. Input the DTC: P0102 or P0103.
  15. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  16. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A227124E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (MASS AIR FLOW RATE)
  1. Connect the Techstream to the DLC3.

  1. Start the engine.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

  1. Read the values displayed on the Techstream.

    Result 
    Mass Air Flow Rate (g/sec.)
    Proceed to
    0.0
    A
    271.0 or more
    B
    Between 1.0 and 270.0*1
    C

    HINT:
    *1: The value must change when the throttle valve is open or closed with the engine running.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
A162182E03
  1. Disconnect the mass air flow meter connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B35-3 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Mass Air Flow Meter)

  1. Reconnect the mass air flow meter connector.



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-5 (VG) - B37-14 (VG)
    Always
    Below 1 Ω
    B35-4 (E2G) - B37-13 (E2G)
    Always
    Below 1 Ω
    B35-5 (VG) or B37-14 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY (EFI MAIN))
  1. Disconnect the mass air flow meter connector.

  1. Remove the No. 1 integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-3 (+B) - 1D-4
    Always
    Below 1 Ω
    B35-3 (+B) or 1D-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)  

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
  1. Disconnect the mass air flow meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-4 (E2G) - Body ground
    Always
    Below 1 Ω



NG
Go to step 7
OK

REPLACE MASS AIR FLOW METER 

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-5 (VG) - B37-14 (VG)
    Always
    Below 1 Ω
    B35-4 (E2G) - B37-13 (E2G)
    Always
    Below 1 Ω
    B35-5 (VG) or B37-14 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)