Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > Sliding Roof Control Switch Circuit

for Preparation Click here


DESCRIPTION

The sliding roof drive gear sub-assembly receives sliding roof switch signals and drives its built-in motor.

WIRING DIAGRAM


B240414E01


INSPECTION PROCEDURE

NOTICE:
When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (Click here).

1.PERFORM ACTIVE TEST USING TECHSTREAM (SLIDING ROOF)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that the sliding roof slides open/closed and tilts up/down (Click here).

    Sliding Roof 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Slide Roof
    Operate sliding roof
    Opn/Dwn: Sliding roof slide open or tilt down operation occurs
    Clos/Up: Sliding roof slide close or tilt up operation occurs
    OFF: Sliding roof not operating
    -

    OK:
    The sliding roof operates normally.



NG
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)
OK


2.READ VALUE USING TECHSTREAM (SLIDING ROOF)
  1. Using the Techstream, read the Data List (Click here).

    Sliding Roof 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Open Switch
    Slide open switch signal / ON or OFF
    ON: Slide open switch pressed
    OFF: Slide open switch not pressed
    -
    Close Switch
    Slide close switch signal / ON or OFF
    ON: Slide close switch pressed
    OFF: Slide close switch not pressed
    -
    Up Switch
    Tilt up switch signal / ON or OFF
    ON: Tilt up switch pressed
    OFF: Tilt up switch not pressed
    -
    Down Switch
    Tilt down switch signal / ON or OFF
    ON: Tilt down switch pressed
    OFF: Tilt down switch not pressed
    -

    OK:
    When operating the switch, the Techstream displays as shown in the table.



NG
Go to step 3
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)  

3.INSPECT MAP LIGHT ASSEMBLY
E198779E02
  1. Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (UP) - 1 (GND)
    Tilt up switch pressed
    Below 1 Ω
    5 (UP) - 1 (GND)
    Tilt up switch not pressed
    10 kΩ or higher
    4 (DOWN) - 1 (GND)
    Tilt down switch pressed
    Below 1 Ω
    4 (DOWN) - 1 (GND)
    Tilt down switch not pressed
    10 kΩ or higher
    3 (OPN) - 1 (GND)
    Slide open switch pressed
    Below 1 Ω
    3 (OPN) - 1 (GND)
    Slide open switch not pressed
    10 kΩ or higher
    2 (CLS) - 1 (GND)
    Slide close switch pressed
    Below 1 Ω
    2 (CLS) - 1 (GND)
    Slide close switch not pressed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Map Light Assembly)



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)
  1. Disconnect the S8 ECU connector.

  1. Disconnect the U2 map light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S8-10 (UP) - U2-5 (UP)
    Always
    Below 1 Ω
    S8-8 (DWN) - U2-4 (DOWN)
    Always
    Below 1 Ω
    S8-7 (OPN) - U2-3 (OPN)
    Always
    Below 1 Ω
    S8-9 (CLS) - U2-2 (CLS)
    Always
    Below 1 Ω
    U2-1 (GND) - Body ground
    Always
    Below 1 Ω
    S8-2 (E) - Body ground
    Always
    Below 1 Ω
    S8-10 (UP) or U2-5 (UP) - Body ground
    Always
    10 kΩ or higher
    S8-8 (DWN) or U2-4 (DOWN) - Body ground
    Always
    10 kΩ or higher
    S8-7 (OPN) or U2-3 (OPN) - Body ground
    Always
    10 kΩ or higher
    S8-9 (CLS) or U2-2 (CLS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)