Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0724    Brake Switch "B" Circuit High

for Preparation Click here


DESCRIPTION

The stop light switch assembly is part of a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly.
This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0724
Stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be stored.

MONITOR STRATEGY


Related DTCs
P0724: Stop light switch/Range check/Rationality
Required sensors/Components
Stop light switch, Vehicle speed sensor
Frequency of operation
Continuous
Duration
GO and STOP 5 times
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present
None
Battery voltage
8 V or higher
Starter
OFF
Ignition switch
ON
GO: Vehicle speed
30 km/h (18.65 mph) or more
STOP: Vehicle speed
Less than 3 km/h (1.86 mph)

TYPICAL MALFUNCTION THRESHOLDS


Stop light switch
Stuck on

CONFIRMATION DRIVING PATTERN


A199312E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Wait 5 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0724.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [E] again.

  12. Start the engine [C].
  13. Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less [D]. Repeat step [D] 5 times.

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Check the DTC judgment result [E].
  15. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0504 .

INSPECTION PROCEDURE

HINT:
Using the Techstream to read the Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream ON.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. Follow the instructions on the Techstream and read the Data List.

Item
Measurement Item/Range (Display)
Normal Condition
Diagnostic Note
Stop Light Switch
Stop light switch status/
ON or OFF
  1. Brake pedal depressed: ON
  2. Brake pedal released: OFF
-
1.READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Primary / Stop Light Switch.

  1. Read the value displayed on the Techstream.

    OK 
    Techstream Display
    Measurement Item/Range
    Normal Condition
    Stop Light Switch
    Stop light switch status/
    ON or OFF
    1. Brake pedal depressed: ON
    2. Brake pedal released: OFF



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
  1. Check the stop light switch assembly installation (Click here).

    OK:
    Stop light switch assembly is installed correctly.



NG
SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


3.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here ).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


4.CHECK TERMINAL VOLTAGE (STP VOLTAGE)


    A220581E36
  1. Disconnect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F50-18 (STP) - Body ground
    Brake pedal depressed
    7.5 to 14 V
    F50-18 (STP) - Body ground
    Brake pedal released
    Below 1.5 V

    Text in Illustration 
    *a
    Brake Pedal Depressed
    *b
    Brake Pedal Released
    *c
    Rear view of wire harness connector
    (to ECM)

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)