Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0340    Camshaft Position Sensor Circuit Malfunction

DTC    P0342    Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)

DTC    P0343    Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)

DTC    P0345    Camshaft Position Sensor "A" Circuit (Bank 2)

DTC    P0347    Camshaft Position Sensor "A" Circuit Low Input (Bank 2)

DTC    P0348    Camshaft Position Sensor "A" Circuit High Input (Bank 2)

for Preparation Click here


DESCRIPTION

The intake camshaft's Variable Valve Timing (VVT) sensor (VV1, VV2 signal) consists of a magnet and MRE (Magnetoresistive Element).
The camshaft timing gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends the camshaft angle data to the ECM.
The crankshaft position sensor plate has 34 teeth. The pickup coil generates 34 signals for each crankshaft revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No.
DTC Detection Condition
Trouble Area
P0340
Either condition is met:
  1. No VVT sensor signal is sent to the ECM while cranking (2 trip detection logic).
  2. There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing gear for intake camshaft
  4. Timing chain for intake camshaft has jumped tooth
  5. ECM
P0345
There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing gear for intake camshaft
  4. Timing chain for intake camshaft has jumped tooth
  5. ECM
P0342
P0347
Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing gear for intake camshaft
  4. Timing chain for intake camshaft has jumped tooth
  5. ECM
P0343
P0348
Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor circuit for intake camshaft
  2. VVT sensor for intake camshaft
  3. Camshaft timing gear for intake camshaft
  4. Timing chain for intake camshaft has jumped tooth
  5. ECM

  1. A199235E01
    Reference: Inspection using an oscilloscope

    HINT:
    1. The correct waveforms are as shown.
    2. VV1+ and VV2+ are the VVT sensor signals, and NE+ is the crankshaft position sensor signal.

    Item
    Content
    Terminal
    NE+ - NE-
    VV1+ - VV1-
    VV2+ - VV2-
    Equipment Setting
    5 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the VVT sensor.

MONITOR STRATEGY


Related DTCs
P0340: VVT sensor (bank 1) verify pulse input (cranking)
P0340: VVT position/Crankshaft position misalignment (bank 1)
P0342: VVT sensor (bank 1) range check (low voltage)
P0343: VVT sensor (bank 1) range check (high voltage)
P0345: VVT position/Crankshaft position misalignment (bank 2)
P0347: VVT sensor (bank 2) range check (low voltage)
P0348: VVT sensor (bank 2) range check (high voltage)
Required Sensors/Components (Main)
VVT sensor (bank 1 and 2)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
5 seconds
MIL Operation
2 driving cycles: P0340 (cranking)
Immediate: Others
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0340 (Cranking) 
Starter
ON
Minimum battery voltage
Below 11 V

P0340 (Engine Running) 
Monitor runs whenever following DTCs are not present
P0342, P0343 (VVT Sensor)
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
Engine speed
600 rpm or more
Starter
OFF
VVT sensor voltage
0.3 to 4.7 V

P0345 (Engine Running) 
Monitor runs whenever following DTCs are not present
P0342, P0343, P0347, P0348 (VVT Sensor)
Engine speed
600 rpm or more
Battery voltage
8 V or higher
Starter
OFF
Ignition switch
ON
VVT sensor voltage
0.3 to 4.7 V

P0342, P0343 (Low Voltage, High Voltage) 
Monitor runs whenever following DTCs are not present
P0340 (VVT Sensor)
Starter
OFF
Ignition switch
ON
Time after ignition switch off to ON
2 seconds or more
Battery voltage
8 V or higher

P0347, P0348 (Low Voltage, High Voltage) 
Monitor runs whenever following DTCs are not present
P0340, P0345 (VVT Sensor)
Starter
OFF
Ignition switch
ON
Time after ignition switch off to ON
2 seconds or more
Battery voltage
8 V or higher

TYPICAL MALFUNCTION THRESHOLDS


P0340 (Cranking) 
VVT sensor signal
No signal

P0340 (Engine Running) 
Camshaft position and crankshaft position phase
Misaligned
VVT sensor signal
No signal

P0345 (Engine Running) 
VVT sensor signal
No signal

P0342 (Low Voltage) 
VVT sensor voltage
Below 0.3 V

P0343 (High Voltage) 
VVT sensor voltage
Higher than 4.7 V

P0347 (Low Voltage) 
VVT sensor voltage
Below 0.3 V

P0348 (High Voltage) 
VVT sensor voltage
Higher than 4.7 V

COMPONENT OPERATING RANGE


VVT sensor voltage
0.3 to 4.7 V

CONFIRMATION DRIVING PATTERN


A198821E06

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. Idle the engine for 10 seconds or more [B].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0335 .

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK TERMINAL VOLTAGE (SENSOR POWER SOURCE)


    A208648E09
  1. Disconnect the VVT sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    B21-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V
    B22-3 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.0 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to VVT Sensor)

  1. Reconnect the VVT sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM)
  1. Disconnect the VVT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B21-1 (VVR+) - B36-9 (VV1+)
    Always
    Below 1 Ω
    B21-2 (VVR-) - B36-10 (VV1-)
    Always
    Below 1 Ω
    B22-1 (VVL+) - B36-12 (VV2+)
    Always
    Below 1 Ω
    B22-2 (VVL-) - B36-11 (VV2-)
    Always
    Below 1 Ω
    B21-1 (VVR+) or B36-9 (VV1+) - Body ground
    Always
    10 kΩ or higher
    B21-2 (VVR-) or B36-10 (VV1-) - Body ground
    Always
    10 kΩ or higher
    B22-1 (VVL+) or B36-12 (VV2+) - Body ground
    Always
    10 kΩ or higher
    B22-2 (VVL-) or B36-11 (VV2-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the VVT sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT)


    BR03795E17
  1. Check the VVT sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
  1. Check the teeth of the signal plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (Click here)
OK


5.REPLACE VVT SENSOR
  1. Replace the VVT sensor (Click here).


NEXT


6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code / Pending.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    No output
    A
    P0340, P0342, P0343, P0345, P0347 or P0348
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END