Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1800/51    Short in Driver Side Squib Circuit

DTC    B1801/51    Open in Driver Side Squib Circuit

DTC    B1802/51    Short to GND in Driver Side Squib Circuit

DTC    B1803/51    Short to B+ in Driver Side Squib Circuit

for Preparation Click here


DESCRIPTION

  1. The driver side squib circuit consists of the center airbag sensor, spiral cable and steering pad.
  2. The circuit instructs the SRS to deploy when deployment conditions are met.
  3. These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1800/51
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the driver side squib circuit during the primary check.
  2. A driver side squib malfunction.
  3. A spiral cable malfunction.
  4. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1801/51
One of the following conditions is met:
  1. The center airbag sensor detects an open circuit signal in the driver side squib circuit for 2 seconds.
  2. A driver side squib malfunction.
  3. A spiral cable malfunction.
  4. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1802/51
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.
  2. A driver side squib malfunction.
  3. A spiral cable malfunction.
  4. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1803/51
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.
  2. A driver side squib malfunction.
  3. A spiral cable malfunction.
  4. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM


C180430E03


INSPECTION PROCEDURE

NOTICE:
  1. When installing the spiral cable and steering wheel, be sure to adjust the spiral cable as it may break if the steering wheel is turned before adjusting the spiral cable (Click here).
  2. When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the Techstream (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).

1.CHECK STEERING PAD (DRIVER SIDE SQUIB)


    C213939E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the steering pad.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

    CAUTION:
    Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800, B1801, B1802 or B1803 is not output.

    HINT:
    Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Driver Side Squib
    *2
    Spiral Cable
    *3
    Center Airbag Sensor
    *4
    Connector E
    *5
    SST
    *a
    Front view of wire harness connector
    (to Driver Side Squib)
    *b
    Color: Orange



NG
Go to step 2
OK

REPLACE STEERING PAD (Click here)  

2.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.



    C214772E01
  1. Check that the spiral cable connectors (on the steering pad side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.

    Text in Illustration 
    *1
    Driver Side Squib
    *2
    Spiral Cable
    *3
    Center Airbag Sensor



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


3.CHECK DRIVER SIDE SQUIB CIRCUIT


    C213940E01
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Z12-2 (D+) - Body ground
    Ignition switch ON
    Below 1 V
    Z12-1 (D-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z12-2 (D+) - Z12-1 (D-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Z12-2 (D+) - Z12-1 (D-)
    Always
    1 MΩ or higher
    Z12-2 (D+) - Body ground
    Always
    1 MΩ or higher
    Z12-1 (D-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Driver Side Squib
*2
Spiral Cable
*3
Center Airbag Sensor
*4
Connector E
*a
Front view of wire harness connector
(to Driver Side Squib)
*b
Color: Orange


NG
Go to step 5
OK


4.CHECK CENTER AIRBAG SENSOR


    C146246E04
  1. Connect the connectors to the steering pad and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800, B1801, B1802 or B1803 is not output.

    HINT:
    Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Driver Side Squib
    *2
    Spiral Cable
    *3
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)


    C213941E01
  1. Restore the released activation prevention mechanism of connector B to its original condition.

  1. Disconnect the instrument panel wire connector from the spiral cable.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F24-1 (D+) - Body ground
    Ignition switch ON
    Below 1 V
    F24-2 (D-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-1 (D+) - F24-2 (D-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-1 (D+) - F24-2 (D-)
    Always
    1 MΩ or higher
    F24-1 (D+) - Body ground
    Always
    1 MΩ or higher
    F24-2 (D-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Instrument Panel Wire
*2
Spiral Cable
*3
Center Airbag Sensor
*4
Connector C
*a
Rear view of wire harness connector
(to Spiral Cable)


NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)